The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The zero-length packet is the sendor tells the receiver that there
is no more data, so it is only needed at the TX side.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system configuration API should be called before the controller
run, otherwise, undefined results may occur. So, we override hcd
reset API, and add system configuration API after controller reset.
Cc: Li Jun <peter.chen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
The struct ci_hdrc is the drvdata for hcd device, so we don't
need to introduce extra ci_hdrc structure for ehci.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
We can support USB OTG 1.3 USB_DEVICE_A_HNP_SUPPORT request when
the driver supports OTG FSM mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Just small ALPS and Elan touchpads, and other driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add special check for fw_version 0x470f01 touchpad
Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
Input: axp20x-pek - add module alias
Input: turbografx - fix potential out of bound access
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2. No area does particularly stand
out but we have a two unpleasant ones:
- Kernel ptes are marked with a global bit which allows the kernel to
share kernel TLB entries between all processes. For this to work
both entries of an adjacent even/odd pte pair need to have the
global bit set. There has been a subtle race in setting the other
entry's global bit since ~ 2000 but it take particularly
pathological workloads that essentially do mostly vmalloc/vfree to
trigger this.
This pull request fixes the 64-bit case but leaves the case of 32
bit CPUs with 64 bit ptes unsolved for now. The unfixed cases
affect hardware that is not available in the field yet.
- Instruction emulation requires loading instructions from user space
but the current fast but simplistic approach will fail on pages
that are PROT_EXEC but !PROT_READ. For this reason we temporarily
do not permit this permission and will map pages with PROT_EXEC |
PROT_READ.
The remainder of this pull request is more or less across the field
and the short log explains them well"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make set_pte() SMP safe.
MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
MIPS: Flush RPS on kernel entry with EVA
Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
MIPS: BMIPS: Delete unused Kconfig symbol
MIPS: Export get_c0_perfcount_int()
MIPS: show_stack: Fix stack trace with EVA
MIPS: do_mcheck: Fix kernel code dump with EVA
MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
MIPS: Partially disable RIXI support.
MIPS: Handle page faults of executable but unreadable pages correctly.
MIPS: Malta: Don't reinitialise RTC
MIPS: unaligned: Fix build error on big endian R6 kernels
MIPS: Fix sched_getaffinity with MT FPAFF enabled
MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
CPUFREQ: Loongson2: Fix broken build due to incorrect include.
Pull btrfs fix from Chris Mason:
"We have a btrfs quota regression fix.
I merged this one on Thursday and have run it through tests against
current master.
Normally I wouldn't have sent this while you were finalizing rc6, but
I'm feeding mosquitoes in the adirondacks next week, so I wanted to
get this one out before leaving. I'll leave longer tests running and
check on things during the week, but I don't expect any problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: Fix a regression in qgroup reserved space.
Pull thermal management fixes from Zhang Rui:
"Specifics:
- fix an error that "weight_attr" sysfs attribute is not removed
while unbinding. From: Viresh Kumar.
- fix power allocator governor tracing to return the real request.
From Javi Merino.
- remove redundant owner assignment of hisi platform thermal driver.
From Krzysztof Kozlowski.
- a couple of small fixes of Exynos thermal driver. From Krzysztof
Kozlowski and Chanwoo Choi"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Drop owner assignment from platform_driver
thermal: exynos: Remove unused code related to platform_data on probe()
thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF
thermal: exynos: Disable the regulator on probe failure
thermal: power_allocator: trace the real requested power
thermal: remove dangling 'weight_attr' device file
>From the usb 3.1 spec available at http://www.usb.org/developers/docs/
table 10-7 (Hub Class Requests) specifies the values for SetHubDepth and
GetPortErrorCount as:
Request bmRequestType bRequest wValue wIndex wLength Data
SetHubDepth 00100000B SET_HUB_DEPTH Hub Depth Zero Zero None
GetPortErrorCount 10100011B GET_PORT_ERR_COUNT Zero Port Two Number of Link Errors on this port
Fix these two values to match the spec.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed some checkpatch.pl warnings saying there was an unwanted space between
function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two occurrences of the checkpatch.pl error:
ERROR: space prohibited before that ',' (ctx:WxW)
Fix one occurrence of the checkpatch error:
ERROR: space required before the open parenthesis '('
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables xhci driver to support SPC by handling
Stopped - Short Packet event in transfer event path.
If SPC = '1' and the stop endpoint command is executed, after a Short
Packet condition has been detected, but before the end of the TD has been
reached, (i.e. the TD is in progress for pipe), then a Transfer Event TRB
with its Completion Code set to Stopped - Short Packet and its TRB
Transfer Length set to value of the EDTLA shall be forced for the
interrupted TRB, irrespective of whether its IOC or ISP flags are set.
This Transfer Event TRB will precede the Command Completion Event TRB for
the command, and is referred to as a Stopped Transfer Event.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Contiguous Frame ID Capability is supported (CFC = 1),
then the xHC shall match the Frame ID in every Isoch TD with
SIA = 0 against the Frame Index of the MFINDEX register. This
rule ensures resynchronization of Isoch TDs even if some are
dropped due to Missed Service Errors or Stopping the endpoint.
This patch enables xHCI driver to support CFC by calculating
and setting the Frame ID field of an Isoch TRB.
[made some dbg messages checkpatch friendly -Mathias]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now xhci-plat-hcd can be built when using one of platform specific
drivers only (mvebu/rcar). There shouldn't be such limitation as some
platforms may not require any quirks and may want to just use a generic
driver ("generic-xhci" / "xhci-hcd").
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding software workaround for LLOCK/SCOND livelock
Fallout of a recent pt_regs update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gFBX
-----END PGP SIGNATURE-----
Merge tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Here's a late pull request for accumulated ARC fixes which came out of
extended testing of the new ARCv2 port with LTP etc. llock/scond
livelock workaround has been reviewed by PeterZ. The changes look a
lot but I've crafted them into finer grained patches for better
tracking later.
I have some more fixes (ARC Futex backend) ready to go but those will
have to wait for tglx to return from vacation.
Summary:
- Enable a reduced config of HS38 (w/o div-rem, ll64...)
- Add software workaround for LLOCK/SCOND livelock
- Fallout of a recent pt_regs update"
* tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: spinlock/rwlock/atomics: reduce 1 instruction in exponential backoff
ARC: Make pt_regs regs unsigned
ARCv2: spinlock/rwlock: Reset retry delay when starting a new spin-wait cycle
ARCv2: spinlock/rwlock/atomics: Delayed retry of failed SCOND with exponential backoff
ARC: LLOCK/SCOND based rwlock
ARC: LLOCK/SCOND based spin_lock
ARC: refactor atomic inline asm operands with symbolic names
Revert "ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock"
ARCv2: [axs103_smp] Reduce clk for Quad FPGA configs
ARCv2: Fix the peripheral address space detection
ARCv2: allow selection of page size for MMUv4
ARCv2: lib: memset: Don't assume 64-bit load/stores
ARCv2: lib: memcpy: Missing PREFETCHW
ARCv2: add knob for DIV_REV in Kconfig
ARC/time: Migrate to new 'set-state' interface
A last minute fix for the new virtio input driver. It seems pretty obvious, and
the problem it's fixing would be quite hard to debug.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVxEFEAAoJECgfDbjSjVRpRLUH/3pwKkwvK8Hf7b9dhJX7HNQf
8Kb+D95Ga/4fNOtmi03GDm6TrfS+sCocKEeTQ7KTm9KraoI61wOn9qsdIH+6HVRL
Ear2fWp4gEZ7bS9n5XwY8AXUHzkbf+Xisg5pQxMex2qtFzEvNof2fD9ra883iLGQ
T4IyAvxclcsiHEy5fxtYHskjKi1t+qxch8cstydaIHddW64TSJPwsbU3k1PQulM/
pxueJRLwc5PvSCeIWiiNbiKNZ7oUtZO9LFwIGCrXESBEZ+YEhmNxK/J1CV6s8bNd
fkuG+szgspl7lNv30NoYqa1RokMh1j8tx90POUwFYyyptK1u5mHOr06+BFr7C6g=
=hz0N
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fix from Michael Tsirkin:
"A last minute fix for the new virtio input driver. It seems pretty
obvious, and the problem it's fixing would be quite hard to debug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-input: reset device and detach unused during remove
- Fix for a 4.2 DM thinp discard regression due to inability to properly
delete a range of blocks in a data mapping btree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVxNokAAoJEMUj8QotnQNaclUIALSoAHN1B47juyNgEjkDQI8x
LodGbto3gLIigsYTrVMH13ohwVaekErsYbe65L8wQT5vyNcXbHTs6YRyCfVAdEhb
4/hmGkVaRtitnHwxrzUv+ycCb1Gj/rtSGdt264AiSMAL2cD/ucL1aLYhkiEdGp9k
hv5qKxjFyzSK0NVAuKn5B8tNtNGVMQv4faTiWKs5JVA4a8RERD2B4+nDROJY3SwM
zgHUPMsPAUb4uphwa0q+qhhrGZWAspS43fCjVBbjXi9lSeUV0TpeYoG4tV7A8T+o
jP9xq4kCLbZ7PzYjMWp6s30+H741Wi1AkBx0NkS7Aoz9kt+SBMlTMFXojPP5Pks=
=AkR0
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- stable fix for a dm_merge_bvec() regression on 32 bit Fedora systems.
- fix for a 4.2 DM thinp discard regression due to inability to
properly delete a range of blocks in a data mapping btree.
* tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree remove: fix bug in remove_one()
dm: fix dm_merge_bvec regression on 32 bit systems
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=geMs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only bulk changes in this request is ABI updates for ASoC topology
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio"
* tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: topology: Add private data type and bump ABI version to 3
ASoC: topology: Add ops support to byte controls UAPI
ASoC: topology: Update TLV support so we can support more TLV types
ASoC: topology: add private data to manifest
ASoC: topology: Add subsequence in topology
ALSA: hda - one Dell machine needs the headphone white noise fixup
ALSA: fireworks/firewire-lib: add support for recent firmware quirk
Revert "ALSA: fireworks: add support for AudioFire2 quirk"
ASoC: topology: fix typo in soc_tplg_kcontrol_bind_io()
ALSA: HDA: Dont check return for snd_hdac_chip_readl
ALSA: HDA: Fix stream assignment for host in decoupled mode
ASoC: rt5645: Fix lost pin setting for DMIC1
ALSA: oxygen: Fix logical-not-parentheses warning
ASoC: Intel: sst_byt: fix initialize 'NULL device *' issue
ASoC: Intel: haswell: fix initialize 'NULL device *' issue
ASoC: cs4265: Fix setting dai format for Left/Right Justified
Blacklist Dell Studio XPS 8100 in dell-smm to fix fan control problems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VZ6x
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Export module alias information in g762 and nct7904 to support
auto-loading.
- Blacklist Dell Studio XPS 8100 in dell-smm to fix fan control
problems.
* tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (g762) Export OF module alias information
hwmon: (nct7904) Export I2C module alias information
hwmon: (dell-smm) Blacklist Dell Studio XPS 8100
Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
issues.
All of these have been in the linux-next tree for a while, full details
on the patches are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXFMe4ACgkQMUfUDdst+ykcxgCfbv91Efs37AUe7LDiIpaperpJ
wIMAn3xwaOsw8qrpcg3YGOaSggMhuuMC
=vwz8
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
issues.
All of these have been in the linux-next tree for a while, full
details on the patches are in the shortlog below"
* tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
ARM: dts: dra7: Add syscon-pllreset syscon to SATA PHY
drivers/usb: Delete XHCI command timer if necessary
xhci: fix off by one error in TRB DMA address boundary check
usb: udc: core: add device_del() call to error pathway
phy: ti-pipe3: i783 workaround for SATA lockup after dpll unlock/relock
phy-sun4i-usb: Add missing EXPORT_SYMBOL_GPL for sun4i_usb_phy_set_squelch_detect
USB: sierra: add 1199:68AB device ID
usb: gadget: f_printer: actually limit the number of instances
usb: gadget: f_hid: actually limit the number of instances
usb: gadget: f_uac2: fix calculation of uac2->p_interval
usb: gadget: bdc: fix a driver crash on disconnect
usb: chipidea: ehci_init_driver is intended to call one time
USB: qcserial: Add support for Dell Wireless 5809e 4G Modem
USB: qcserial/option: make AT URCs work for Sierra Wireless MC7305/MC7355
Here are 3 bugfixes for some staging driver issues that have been
reported. All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXFMPgACgkQMUfUDdst+ynyMQCgvh9otlknntPMSTzWQg5grZJ9
0ncAoJy+MiCvhfk4WBwUJkIQv894VgXG
=mpUf
-----END PGP SIGNATURE-----
Merge tag 'staging-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three bugfixes for some staging driver issues that have been
reported. All have been in the linux-next tree for a while"
* tag 'staging-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: Include unaligned.h instead of access_ok.h
staging: vt6655: vnt_bss_info_changed check conf->beacon_rate is not NULL
staging: comedi: das1800: add missing break in switch
Here are some extcon fixes for 4.2-rc6 that resolve some reported
problems.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXFMm4ACgkQMUfUDdst+yn8wQCgmekm9QrM6f9ta+HRCtoR4njo
IuUAn1cK2bZnWqzn8tR5duuJE427Uldq
=561n
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some extcon fixes for 4.2-rc6 that resolve some reported
problems.
All have been in linux-next for a while"
* tag 'char-misc-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
extcon: Fix extcon_cable_get_state() from getting old state after notification
extcon: Fix hang and extcon_get/set_cable_state().
extcon: palmas: Fix NULL pointer error
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
It is no need to check the packet[0] for sanity check when doing
elantech_packet_check_v4() function for fw_version = 0x470f01 touchpad.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
remove_one() was not incrementing the key for the beginning of the
range, so not all entries were being removed. This resulted in
discards that were not unmapping all blocks.
Fixes: 4ec331c3ea ("dm btree: add dm_btree_remove_leaves()")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In
commit 99264a61dfcda41d86d0960cf2d4c0fc2758a773
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 15 19:34:43 2015 +0200
drm/vblank: Fixup and document timestamp update/read barriers
I've switched vblank->count from atomic_t to unsigned long and
accidentally created an integer comparison bug in
drm_vblank_count_and_time since vblanke->count might overflow the u32
local copy and hence the retry loop never succeed.
Fix this by consistently using u32.
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVxJsBAAoJECTWi3JdVIfQHUIH/2NeQyG7bL3TSIm0qK9RdmaT
UrWyGm6AwhOrg9j9jnZkXag1v4Fsmo4nnslaDbmCKaWJPs7ol94NuWJK7z3He3nr
47yxl2m8OhxsS7aBDACa4gJFQce+JSjKs1ADnKR7QzY9c1/nTAWLO/LE/I5Ca18u
tZg77hviip2ftfLYdNXDZvz3HzuCcRnIouc4izTs16DXwU3aYpqcctFrcqU3nNmp
/+5zPwIoLA7KDwPqdYhSPNRuCnFtjVbI8hTzq+aWFlxFBZYlKmSCTSwpCN2aQDgF
1oCOP4dlv7s9Xavd2TOMJ8g3Fuyb/gjX2DhIEm7QCYxwBxdkpwm0na6gMrRJqsg=
=NEOq
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.2
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
The increment of delay counter was 2 instructions:
Arithmatic Shfit Left (ASL) + set to 1 on overflow
This can be done in 1 using ROtate Left (ROL)
Suggested-by: Nigel Topham <ntopham@synopsys.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Merge fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
writeback: fix initial dirty limit
mm/memory-failure: set PageHWPoison before migrate_pages()
mm: check __PG_HWPOISON separately from PAGE_FLAGS_CHECK_AT_*
mm/memory-failure: give up error handling for non-tail-refcounted thp
mm/memory-failure: fix race in counting num_poisoned_pages
mm/memory-failure: unlock_page before put_page
ipc: use private shmem or hugetlbfs inodes for shm segments.
mm: initialize hotplugged pages as reserved
ocfs2: fix shift left overflow
kthread: export kthread functions
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
lib/iommu-common.c: do not use 0xffffffffffffffffl for computing align_mask
mm/slub: allow merging when SLAB_DEBUG_FREE is set
signalfd: fix information leak in signalfd_copyinfo
signal: fix information leak in copy_siginfo_to_user
signal: fix information leak in copy_siginfo_from_user32
ocfs2: fix BUG in ocfs2_downconvert_thread_do_work()
fs, file table: reinit files_stat.max_files after deferred memory initialisation
mm, meminit: replace rwsem with completion
mm, meminit: allow early_pfn_to_nid to be used during runtime
...
If we have a series of events from userpsace, with %fprs=FPRS_FEF,
like follows:
ETRAP
ETRAP
VIS_ENTRY(fprs=0x4)
VIS_EXIT
RTRAP (kernel FPU restore with fpu_saved=0x4)
RTRAP
We will not restore the user registers that were clobbered by the FPU
using kernel code in the inner-most trap.
Traps allocate FPU save slots in the thread struct, and FPU using
sequences save the "dirty" FPU registers only.
This works at the initial trap level because all of the registers
get recorded into the top-level FPU save area, and we'll return
to userspace with the FPU disabled so that any FPU use by the user
will take an FPU disabled trap wherein we'll load the registers
back up properly.
But this is not how trap returns from kernel to kernel operate.
The simplest fix for this bug is to always save all FPU register state
for anything other than the top-most FPU save area.
Getting rid of the optimized inner-slot FPU saving code ends up
making VISEntryHalf degenerate into plain VISEntry.
Longer term we need to do something smarter to reinstate the partial
save optimizations. Perhaps the fundament error is having trap entry
and exit allocate FPU save slots and restore register state. Instead,
the VISEntry et al. calls should be doing that work.
This bug is about two decades old.
Reported-by: James Y Knight <jyknight@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull amdgpu fixes from Alex Deucher:
"Just a few amdgpu fixes to make sure we report the proper firmware
information and number of render buffers to userspace and a typo in a
debugging function"
[ Pulling directly from Alex since Dave Airlie is on vacation - Linus ]
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: set fw_version and feature_version for smu fw loading
drm/amdgpu: add feature version for SDMA ucode
drm/amdgpu: add feature version for RLC and MEC v2
drm/amdgpu: increment queue when iterating on this variable.
drm/amdgpu: fix rb setting for CZ
Pull TDA998x i2c driver fixes from Russell King:
"This fixes the double-checksumming of the AVI infoframe which was
resulting in the checksum always being zero. It went unnoticed as
none of my HDMI devices had a problem with this"
[ Pulling directly from rmk since Dave Airlie is on vacation - Linus ]
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix bad checksum of the HDMI AVI infoframe
The initial value of global_wb_domain.dirty_limit set by
writeback_set_ratelimit() is zeroed out by the memset in
wb_domain_init().
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now page freeing code doesn't consider PageHWPoison as a bad page, so by
setting it before completing the page containment, we can prevent the
error page from being reused just after successful page migration.
I added TTU_IGNORE_HWPOISON for try_to_unmap() to make sure that the
page table entry is transformed into migration entry, not to hwpoison
entry.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The race condition addressed in commit add05cecef80 ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit
add05cecef80 about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"non anonymous thp" case is still racy with freeing thp, which causes
panic due to put_page() for refcount-0 page. It seems that closing up
this race might be hard (and/or not worth doing,) so let's give up the
error handling for this case.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
