This patch adds basic support for the new 405EX and the AMCC eval board
Kilauea to arch/powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All ppc32 systems except PReP and 8xx are capable of handling 3G of user
address space. Old legacy had set this to 2GB and no one has bothered to
fix it.
8xx could be bumped up to 3GB if its SW TLB miss handlers were fixed up
to properly determine kernel/user addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using PAGE_OFFSET instead of TASK_SIZE or KERNELBASE value on
6xx/40x/44x/fsl-booke to determine if the faulting address is a kernel or
user space address. This mimics how the macro is_kernel_addr() works.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
asm-powerpc/mpc85xx.h was really a hold over from arch/ppc. Now that
more decoupling has occurred we can remove <asm/mpc85xx.h> and some of
its legacy.
As part of this we moved the definition of CPM_MAP_ADDR into cpm2.h
for 85xx platforms. This is a stop gap until drivers stop using
CPM_MAP_ADDR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use any CPM devices on these boards, but the muram node on these
chips is different from the 8560, so it's helpful to people working with
custom boards based on these chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In testing the new clocksource and clockevent code on a PPC601
processor, I discovered that the clockevent multiplier value for the
decrementer clockevent was overflowing. Because the RTCL register in
the 601 effectively counts at 1GHz (it doesn't actually, but it
increases by 128 every 128ns), and the shift value was 32, that meant
the multiplier value had to be 2^32, which won't fit in an unsigned
long on 32-bit. The same problem would arise on any platform where
the timebase frequency was 1GHz or more (not that we actually have any
such machines today).
This fixes it by reducing the shift value to 16. Doing the
calculations with a resolution of 2^-16 nanoseconds (15 femtoseconds)
should be quite adequate. :)
Signed-off-by: Paul Mackerras <paulus@samba.org>
On old powermacs, we sometimes set the decrementer to 1 in order to
trigger a decrementer interrupt, which we use to handle an interrupt
that was pending at the time when it was re-enabled. This was causing
the decrementer clock event device to call the event function for the
next event early, which was causing problems when high-res timers were
not enabled.
This fixes the problem by recording the timebase value at which the
next event should occur, and checking the current timebase against the
recorded value in timer_interrupt. If it isn't time for the next
event, it just reprograms the decrementer and returns.
This also subtracts 1 from the value stored into the decrementer,
which is appropriate because the decrementer interrupts on the
transition from 0 to -1, not when the decrementer reaches 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some IBM machines supply a "logical" PVR (processor version register)
value in the device tree in the cpu nodes rather than the real PVR.
This is used for instance to indicate that the processors in a POWER6
partition have been configured by the hypervisor to run in POWER5+
mode rather than POWER6 mode. To cope with this, we call identify_cpu
a second time with the logical PVR value (the first call is with the
real PVR value in the very early setup code).
However, POWER5+ machines can also supply a logical PVR value, and use
the same value (the value that indicates a v2.04 architecture
compliant processor). This causes problems for code that uses the
performance monitor (such as oprofile), because the PMU registers are
different in POWER6 (even in POWER5+ mode) from the real POWER5+.
This change works around this problem by taking out the PMU
information from the cputable entries for the logical PVR values, and
changing identify_cpu so that the second call to it won't overwrite
the PMU information that was established by the first call (the one
with the real PVR), but does update the other fields. Specifically,
if the cputable entry for the logical PVR value has num_pmcs == 0,
none of the PMU-related fields get used.
So that we can create a mixed cputable entry, we now make cur_cpu_spec
point to a single static struct cpu_spec, and copy stuff from
cpu_specs[i] into it. This has the side-effect that we can now make
cpu_specs[] be initdata.
Ultimately it would be good to move the PMU-related fields out to a
separate structure, pointed to by the cputable entries, and change
identify_cpu so that it saves the PMU info pointer, copies the whole
structure, and restores the PMU info pointer, rather than identify_cpu
having to list all the fields that are *not* PMU-related.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't allow cpu hotplug on systems lacking XICS interrupt controller
(i.e. with an MPIC interrupt controller), since the current pSeries
platform code is hardcoded for XICS.
This works around the bug reported by Paul Mackerras where the
disable_nonboot_cpus() call recently added to the shutdown path will
cause an oops on older pSeries machines.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer initialise the name and owner fields of the
of_platform_driver, but use the fields of the embedded device_driver's
name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This way we only have entries in the device tree for disks that actually
exist. A slight complication is that disks may be attached to LPARs
at runtime.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now we will only have entries in the device tree for the actual existing
devices (including their OS/400 properties). This way viotape.c gets
all the information about the devices from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now we will only have entries in the device tree for the actual existing
devices (including their OS/400 properties). This way viocd.c gets all
the information about the devices from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It was only being used to carry around dma_iommu_ops and vio_iommu_table
which we can use directly instead. This also means that vio_bus_device
doesn't need to refer to them either.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to keep a lump of dma coherent memory around for the life
of the module.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove vio_dma_ops declaration (since it no longer exists) and some
unused fields from struct vio_driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no good reason for board platform code to mess with the
ROOT_DEV. Remove it from all in-tree platforms except powermac.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows platforms which don't have anything to do at setup_arch time
(like a bunch of the 4xx platforms) to eliminate an empty setup_arch hook.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our _GLOBAL macro does a ".align 2" so the alignment is fine for 32
bit, but on 64 bit it is possible for it to end up only 4 byte aligned.
I don't know if it matters, but it can't hurt to 8 byte align it.
It also means that when we build with --emit_relocs, none of our 64 bit
relocations are to misaligned places.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Lite5200 u-boot image doesn't entirely configure the processor
correctly and so Linux needs to fixup the cpu setup in setup_arch. Fixing
the CPU setup is good, but making it into common code is not a good idea.
New board ports should be encouraged not to take the lead of the lite5200
and instead get their firmware to setup the CPU the right way.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>
Drop unnecessary includes for MPC5200 based boards
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>
This hook doesn't really add any new information.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tnt.com>
dcr.c is an arch/powerpc only thing. Compiling ppc405 arch/ppc kernels
throws warnings without this change.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adds the of_platform bus binding to the xilinxfb driver. Needed to
use framebuffer devices described in the OF device tree (used by
arch/powerpc).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Change the platform bus binding to make use of the established
platform_bus API.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Split the device setup code away from the platform bus binding. This is
in preparation for adding the of_platform bus binding to this driver and
most of the setup code is common between the two busses.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Labels and gotos are used in xilinxfb_assign to unwind allocations
on device registration failures. Rename the labels to reflect the
error which occured. This change is being made to make it easier
to add new failout paths (which occurs in a subsuquent patch) and
to make reviewing the failout path easier.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
The dev_dbg, dev_err, etc functions provide more context that plain
vanilla printk which is useful for debugging. Where appropriate,
change printk calls to the appropriate dev_*() call.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Debug support: when DEBUG is defined, output relevant details to the
log about the framebuffer registration.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
There is no BOOTIMG Kconfig variable, not to mention that there is no
include/linux/bootimg.h header file.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for a simple tagged database in the PS3 flash rom
os-area. The database allows the flash rom os-area to be shared
between a bootloader and installed operating systems. The
application ps3-flash-util or the library libps3-utils from the
ps3-utils package can be used for userspace database operations.
The latest ps3-utils package is available here:
git://git.kernel.org/pub/scm/linux/kernel/git/geoff/ps3-utils.git
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the PS3 os-area startup params to the device tree. This allows
a second stage kernel loaded with kexec to use these values.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updates for PS3 os-area rtc_diff set/get routines
o Add a new routine ps3_os_area_set_rtc_diff().
o Rename ps3_os_area_rtc_diff() to ps3_os_area_get_rtc_diff().
o Remove static variable rtc_shift with calls to ps3_os_area_get_rtc_diff().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
