This is similar to b1cb59cf2efe(net: sysctl_net_core: check SNDBUF
and RCVBUF for min length). I don't think too small values can cause
crashes in the case of udp and tcp, but I've seen this set to too
small values which triggered awful performance. It also makes the
setting consistent across all the wmem/rmem sysctls.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathieu Olivari says:
====================
Add support for QCA IPQ806x Ethernet GMAC controller
This patch set adds support for the integrated Ethernet GMAC controller
on QCA IPQ806x SoC. This controller is based on a Gigabit Synopsys
DesignWare IP, already supported in the stmmac driver located in
drivers/net/ethernet/stmicro/stmmac.
This change is done as a follow-up to the following thread:
*http://www.spinics.net/lists/netdev/msg311265.html
While previous attempt was creating a new driver to drive this controller,
this new post leverages the existing stmmac driver by implementing the
SoC specific glue to it.
Aside from the pure stmmac glue layer, we have a couple of related
patches:
*IPQ806x NSS clock addition is cherry-picked and refreshed from the
following thread: https://lkml.org/lkml/2014/8/6/390
*phy-handle and fixed-link support are also added in this change set so the
driver can be fully functional on platforms using device-trees as well as
ethernet switches.
V2:
*Fix MODULE_LICENSE to "Dual BSD/GPL" as the dwmac-ipq806x.c is using
ISC license.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet controller available in IPQ806x is a Synopsys DesignWare
Gigabit MAC IP core, already supported by the stmmac driver.
This glue layer implements some platform specific settings required to
get the controller working on an IPQ806x based platform.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case DT is used, this change adds the ability to the stmmac driver to
detect a fixed-link PHY, instanciate it, and use it during
phy_connect().
Fixed link PHYs DT usage is described in:
Documentation/devicetree/bindings/net/fixed-link.txt
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.
This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-05-28
1) Remove xfrm_queue_purge as this is the same as skb_queue_purge.
2) Optimize policy and state walk.
3) Use a sane return code if afinfo registration fails.
4) Only check fori a acquire state if the state is not valid.
5) Remove a unnecessary NULL check before xfrm_pol_hold
as it checks the input for NULL.
6) Return directly if the xfrm hold queue is empty, avoid
to take a lock as it is nothing to do in this case.
7) Optimize the inexact policy search and allow for matching
of policies with priority ~0U.
All from Li RongQing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace confusing QL_STATUS_INVALID_PARAM == -1 == -EPERM with -EINVAL
and QLC_STATUS_UNSUPPORTED_CMD == -2 == -ENOENT with -EOPNOTSUPP, the
latter error code is arguable, but it is already used in the driver,
so let it be here as well.
Also remove always false (!buf) check on read(), the driver should
not care if userspace gets its EFAULT or not.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these files were only building on non-x86 because of
the indirect of inclusion of vmalloc.h by, of all things,
"net/inet_hashtables.h"
None of this got caught during build testing, because on x86
there is an implicit vmalloc.h include via on of the arch asm/
headers.
This fixes all of these
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07f4c90062 ("tcp/dccp: try to not exhaust
ip_local_port_range in connect()") it is advised to have an even number
of ports described in /proc/sys/net/ipv4/ip_local_port_range
This means start/end values should have a different parity.
Let's warn sysadmins of this, so that they can update their settings
if they want to.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__inet_hash_connect() does not use its third argument (port_offset)
if socket was already bound to a source port.
No need to perform useless but expensive md5 computations.
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
cxgb4/cxgb4vf: Adds FL starvation support and cleanup
This patch series adds the following.
Adds debugfs entry to inject freelist starvation and some function and
argument cleanup
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2:
Skipping patch "cxgb4: Add support for loopback between VI of same port".
This needs some major code change, since module param is not recommended.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes variable name 'fn' to 'pf' of structure adapter.
A 'fn' usually stands for PCI function which could be a PF or a VF.
However, the use of this particular variable is explicitly limited to PF
only. So, be specific about it in the variable name.
Also corrects arguments passed for fn t4_ofld_eq_free, t4_ctrl_eq_free,
t4_eth_eq_free, t4_iq_free, t4_alloc_vi, t4_fw_hello, t4_wr_mbox and
t4_cfg_pfvf function.
Also renames cxgb4_t4_bar2_sge_qregs to t4_bar2_sge_qregs and renames
the latter function name in cxgb4vf driver to t4vf_bar2_sge_qregs to
avoid conflicts. Also fixes alignment for these function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry to inject Freelist starvation, used only for debugging
purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc.h used to be included from include/net/inet_hashtables.h
but it is no longer the case.
Fixes: 095dc8e0c3 ("tcp: fix/cleanup inet_ehash_locks_alloc()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumzet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksey Makarov says:
====================
Adding support for Cavium ThunderX network controller
This patchset adds support for the Cavium ThunderX network controller.
changes in v6:
* unused preprocessor symbols were removed
* reduce no of atomic operations in SQ maintenance
* support for TCP segmentation at driver level
* reset RBDR if fifo state is FAIL
* fixed an issue with link state mailbox message
changes in v5:
* __packed were removed. now we rely on C language ABI
* nic_dbg() -> netdev_dbg()
* fixes for a typo, constant spelling and using BIT_ULL
* use print_hex_dump()
* unnecessary conditions in a long if() chain were removed
changes in v4:
* the patch "pci: Add Cavium PCI vendor id" was attributed correctly
* a note that Cavium id is used in many drivers was added
* the license comments now match MODULE_LICENSE
* a comment explaining usage of writeq_relaxed()/readq_relaxed() was added
changes in v3:
* code cleanup
* issues discovered by reviewers were addressed
changes in v2:
* non-generic module parameters removed
* ethtool support added (nicvf_set_rxnfc())
v5: https://lkml.kernel.org/g/<1432344498-17131-1-git-send-email-aleksey.makarov@caviumnetworks.com>
v4: https://lkml.kernel.org/g/<1432000757-28700-1-git-send-email-aleksey.makarov@auriga.com>
v3: https://lkml.kernel.org/g/<1431747401-20847-1-git-send-email-aleksey.makarov@auriga.com>
v2: https://lkml.kernel.org/g/<1415596445-10061-1-git-send-email-rric@kernel.org>
v1: https://lkml.kernel.org/g/<20141030165434.GW20170@rric.localhost>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Cavium ThunderX network controller.
The driver is on the pci bus and thus requires the Thunder PCIe host
controller driver to be enabled.
Signed-off-by: Maciej Czekaj <mjc@semihalf.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Kamil Rytarowski <kamil@semihalf.com>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sruthi Vangala <svangala@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This vendor id will be used by network (vNIC), USB (xHCI),
SATA (AHCI), GPIO, I2C, MMC and maybe other drivers
for ThunderX SoC.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While 3b52960266 ("test_bpf: add more eBPF jump torture cases")
added the int3 bug test case only for eBPF, which needs exactly 11
passes to converge, here's a version for classic BPF with 11 passes,
and one that would need 70 passes on x86_64 to actually converge for
being successfully JITed. Effectively, all jumps are being optimized
out resulting in a JIT image of just 89 bytes (from originally max
BPF insns), only returning K.
Might be useful as a receipe for folks wanting to craft a test case
when backporting the fix in commit 3f7352bf21 ("x86: bpf_jit: fix
compilation of large bpf programs") while not having eBPF. The 2nd
one is delegated to the interpreter as the last pass still results
in shrinking, in other words, this one won't be JITed on x86_64.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: add MCDI tracing
This patchset adds support for logging MCDI (Management-Controller-to-
Driver Interface) interactions between the sfc driver and a bound device,
to aid in debugging.
Solarflare has a tool to decode the resulting traces and will look to
open-source this if there is any external interest, but the protocol is
already detailed in drivers/net/ethernet/sfc/mcdi_pcol.h.
The logging buffer we allocate per MCDI context is a work area for
constructing each individual message before logging it with netif_info.
The reason the buffer is long-lived is simply to avoid the overhead of
allocating and freeing it every MCDI call, since MCDIs are already known
to be serialised for other reasons.
--
v4: remove patch #4, which has already been applied via sshah
v3: add some explanations to cover letter and patch #4
v2: avoid long lines in cover letter; fix multiline comment style
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As many issues are encountered at probe time, where MCDI logging can't be
enabled through the sysfs node, this change adds a module parameter
'mcdi_logging_default', which defaults to false. When set to true, newly-
probed functions will have MCDI logging enabled. The setting can
subsequently be changed as normal through the sysfs node.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is enabled per-function with a sysfs file
/sys/class/net/<NET_DEV>/device/mcdi_logging
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is conditional on CONFIG_SFC_MCDI_LOGGING, which is enabled
by default.
Each MCDI command will produce a console line like
sfc dom🚌dev:fn ifname: MCDI RPC REQ: xxxxxxxx [yyyyyyyy...]
where xxxxxxxx etc. are the raw MCDI payload in 32-bit hex chunks.
The response will then produce a similar line with "RESP" instead of "REQ",
and containing the MCDI response payload (if any).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're seeing some softlockups from this function when there
are a lot fdb entries on a vxlan device. Taking the lock for
each bucket instead of the whole table is enough to fix that.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem on busy servers is the tiny available TCP port
range (/proc/sys/net/ipv4/ip_local_port_range) and the default
sequential allocation of source ports in connect() system call.
If a host is having a lot of active TCP sessions, chances are
very high that all ports are in use by at least one flow,
and subsequent bind(0) attempts fail, or have to scan a big portion of
space to find a slot.
In this patch, I changed the starting point in __inet_hash_connect()
so that we try to favor even [1] ports, leaving odd ports for bind()
users.
We still perform a sequential search, so there is no guarantee, but
if connect() targets are very different, end result is we leave
more ports available to bind(), and we spread them all over the range,
lowering time for both connect() and bind() to find a slot.
This strategy only works well if /proc/sys/net/ipv4/ip_local_port_range
is even, ie if start/end values have different parity.
Therefore, default /proc/sys/net/ipv4/ip_local_port_range was changed to
32768 - 60999 (instead of 32768 - 61000)
There is no change on security aspects here, only some poor hashing
schemes could be eventually impacted by this change.
[1] : The odd/even property depends on ip_local_port_range values parity
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: force refragmentation for DF reassembed skbs
output path tests:
if (skb->len > mtu) ip_fragment()
This breaks connectivity in one corner case:
If the skb was reassembled, but has the DF bit set and ..
.. its reassembled size is <= outdev mtu ..
.. we will forward a DF packet larger than what the sender
transmitted on wire.
If a router later in the path can't forward this packet, it will send an
icmp error in response to an mtu that the original sender never exceeded.
This changes ipv4 defrag/output path to
a) force refragmentation for DF reassembled skbs and
b) set DF bit on all fragments when refragmenting if it was set on original
frags.
tested via:
from scapy.all import *
dip="10.23.42.2"
payload="A"*1400
packet=IP(dst=dip,id=12345,flags='DF')/UDP(sport=42,dport=42)/payload
frags=fragment(packet,fragsize=1200)
for fragment in frags:
send(fragment)
Without this patch, we generate fragments without df bit set based
on the outgoing device mtu when fragmenting after forwarding, ie.
IP (ttl 64, id 12345, offset 0, flags [+, DF], proto UDP (17), length 1204)
192.168.7.1.42 > 10.23.42.2.42: UDP, length 1400
IP (ttl 64, id 12345, offset 1184, flags [DF], proto UDP (17), length 244)
192.168.7.1 > 10.23.42.2: ip-proto-17
on ingress will either turn into
IP (ttl 63, id 12345, offset 0, flags [+], proto UDP (17), length 1396)
192.168.7.1.42 > 10.23.42.2.42: UDP, length 1400
IP (ttl 63, id 12345, offset 1376, flags [none], proto UDP (17), length 52)
(mtu 1400: We strip df and send larger fragment), or
IP (ttl 63, id 12345, offset 0, flags [DF], proto UDP (17), length 1428)
192.168.7.1.42 > 10.23.42.2.42: [udp sum ok] UDP, length 1400
if mtu is 1500. And in this case things break; router with a smaller mtu
will send icmp error, but original sender only sent packets <= 1204 byte.
With patch, we keep intent of such fragments and will emit DF-fragments
that won't exceed 1204 byte in size.
Joint work with Hannes Frederic Sowa.
Changes since v2:
- split unrelated patches from series
- rework changelog of patch #2 to better illustrate breakage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently always send fragments without DF bit set.
Thus, given following setup:
mtu1500 - mtu1500:1400 - mtu1400:1280 - mtu1280
A R1 R2 B
Where R1 and R2 run linux with netfilter defragmentation/conntrack
enabled, then if Host A sent a fragmented packet _with_ DF set to B, R1
will respond with icmp too big error if one of these fragments exceeded
1400 bytes.
However, if R1 receives fragment sizes 1200 and 100, it would
forward the reassembled packet without refragmenting, i.e.
R2 will send an icmp error in response to a packet that was never sent,
citing mtu that the original sender never exceeded.
The other minor issue is that a refragmentation on R1 will conceal the
MTU of R2-B since refragmentation does not set DF bit on the fragments.
This modifies ip_fragment so that we track largest fragment size seen
both for DF and non-DF packets, and set frag_max_size to the largest
value.
If the DF fragment size is larger or equal to the non-df one, we will
consider the packet a path mtu probe:
We set DF bit on the reassembled skb and also tag it with a new IPCB flag
to force refragmentation even if skb fits outdev mtu.
We will also set DF bit on each fragment in this case.
Joint work with Hannes Frederic Sowa.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_skb_dst_mtu is small inline helper, but its called in several places.
before: 17061 44 0 17105 42d1 net/ipv4/ip_output.o
after: 16805 44 0 16849 41d1 net/ipv4/ip_output.o
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: phy_interface_is_rgmii helper
As you suggested, here is the helper function to avoid missing some RGMII
interface checks. Had to wait for net to be merged in net-next to avoid
submitting the same patch/commit.
Dan, you might want to rebase your dp83867 submission to use that helper
when you this patchset gets merged into net-next, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII interfaces come in 4 different flavors that the PHY library needs
to care about: regular RGMII (no delays), RGMII with either RX or TX
delay, and both. In order to avoid errors of checking only for one type
of RGMII interface and miss the 3 others, introduce a convenience
function which tests for all values.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to get this indirectly I supposed, but no longer do.
Either way, an explicit include should have been done in the
first place.
net/ipv4/fib_trie.c: In function '__node_free_rcu':
>> net/ipv4/fib_trie.c:293:3: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(n);
^
net/ipv4/fib_trie.c: In function 'tnode_alloc':
>> net/ipv4/fib_trie.c:312:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
return vzalloc(size);
^
>> net/ipv4/fib_trie.c:312:3: warning: return makes pointer from integer without a cast
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
We can then revert 843925f33f
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tcp ehash table is constrained to a very small number of buckets
(eg boot parameter thash_entries=128), then we can crash if spinlock
array has more entries.
While we are at it, un-inline inet_ehash_locks_alloc() and make
following changes :
- Budget 2 cache lines per cpu worth of 'spinlocks'
- Try to kmalloc() the array to avoid extra TLB pressure.
(Most servers at Google allocate 8192 bytes for this hash table)
- Get rid of various #ifdef
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit dd3f9e70f5
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.
However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.
This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF=-D__CHECK_ENDIAN__ net/core/utils.o
...
net/core/utils.c:307:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:307:72: expected restricted __wsum [usertype] addend
net/core/utils.c:307:72: got restricted __be32 [usertype] from
net/core/utils.c:308:34: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:308:34: expected restricted __wsum [usertype] addend
net/core/utils.c:308:34: got restricted __be32 [usertype] to
net/core/utils.c:310:70: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:70: expected restricted __wsum [usertype] addend
net/core/utils.c:310:70: got restricted __be32 [usertype] from
net/core/utils.c:310:77: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:77: expected restricted __wsum [usertype] addend
net/core/utils.c:310:77: got restricted __be32 [usertype] to
net/core/utils.c:312:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:312:72: expected restricted __wsum [usertype] addend
net/core/utils.c:312:72: got restricted __be32 [usertype] from
net/core/utils.c:313:35: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:313:35: expected restricted __wsum [usertype] addend
net/core/utils.c:313:35: got restricted __be32 [usertype] to
Note we can use csum_replace4() helper
Fixes: 58e3cac561 ("net: optimise inet_proto_csum_replace4()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF=-D__CHECK_ENDIAN__ net/core/secure_seq.o
net/core/secure_seq.c:157:50: warning: restricted __be32 degrades to
integer
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check in fdb_add_entry() if the source port should learn, similar
check is used in br_fdb_update.
Note that new fdb entries which are added manually or
as local ones are still permitted.
This patch has been tested by running traffic via a bridge port and
switching the port's state, also by manually adding/removing entries
from the bridge's fdb.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/pktgen.c:2672:43: warning: incorrect type in assignment (different base types)
net/core/pktgen.c:2672:43: expected unsigned short [unsigned] [short] [usertype] <noident>
net/core/pktgen.c:2672:43: got restricted __be16 [usertype] protocol
Let's use proper struct ethhdr instead of hard coding everything.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_select_ident() returns a 32bit value in network order.
Fixes: 286c2349f6 ("ipv6: Clean up ipv6_select_ident() and ip6_fragment()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran says:
====================
cpsw cleanups
While working on an out-of-tree customization, I noticed a few minor
problems in the cpsw code. This series cleans up the issues I found.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There
is no need to disable the dma interrupts twice. This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There
is no need to enable the dma interrupts twice. This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The funtions, cpsw_ale_flush and cpsw_ale_set_ageout, have never been used
since they were first introduced. This patch removes the dead code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the breaks too far to the left makes parsing the dense switch/case
block unnecessarily harder.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
rocker: unused parameter and const cleanups
This series provides some minor though verbose cleanup of rocker.
The second patch depends on the first though it could be rebased.
I had previously asked for v2 to be put on hold while some bugs I had found
in the rocker driver were shaken out. That has now happened and the bugs
turned out to be unrelated. Accordingly I am reposting the series.
* Changes v2 -> v3
- Rebase and update for new variables and parameters that may be const
* Changes v1 -> v2
- Found quite a few more variables and parameters to make const
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark parameters and local variables as const where possible.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./net/irda/timer.c:63:35-37: use of msecs_to_jiffies probably perferable
Converting milliseconds to jiffies by "val * HZ / 1000" technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases. Further the () around the arithmetic expression
was dropped.
Patch was compile tested for x86_64_defconfig + CONFIG_IRDA=m
Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>