When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is defined in include/linux/ieee80211.h. As per IEEE spec.
bit6 to bit15 in block ack parameter represents buffer size.
So the bitmask should be 0xFFC0.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to release_firmware() in order not to leak memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case of alloc_netdev_mq failure and kmalloc failure,
current implementation returns ERR_PTR(0).
As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR
macro. Fix it by setting proper error code for ret variable in the failure
cases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758
Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org # 2.6.34+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334
The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.
The patch applies to 2.6.37.
Signed-off-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some Broadcom based wireless devices contain dangling ethernet cores.
This triggers the ssb probing mechanism and tries to load the b44 driver
on this core.
Ignore the dangling core in the ssb core scanning code to avoid
access to the core and failure of b44 probing.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just create a section to collect the LED trigger
functions and add a very short description as to
what drivers should do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some mesh attribute/command docs are missing or
have errors in the name so they don't match, fix
all of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I made the patch to add mesh join/leave I
didn't pay attention to docs because it was a
proof of concept, and then when we actually did
merge it I forgot -- add docs now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag is IEEE80211_TX_CTL_TX_OFFCHAN and I had
added that in a previous patch but forgotten docs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation for the new callbacks that I
forgot in the patch adding the callbacks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.
Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.
Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.
The previous version of this patch included a printk that was left over from
me fixing the filter setup. This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a compressed input type for atr signature hash
computation. It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.
With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation. The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.
TCP_RR before:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23059.27
16384 87380
TCP_RR after:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23239.98
16384 87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.
The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.
Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants. Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed. We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet. Since we have already computed
this, we can directly use the result instead of figuring it out
again.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches skb_need_linearize() to use the features that have
been centrally computed. In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet. On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time. Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches dev_gso_segment() to use the device features computed
by the centralized routine. In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload. This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features. However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware. This generalizes the function
to return features about all of the various forms of offloading. Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement. This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time. By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware. NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present. The primary advantage of this is multiply tagged vlans can use
hardware checksumming.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It workarounds the 60s firmware load failure timeout for the
non-modular case.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new kernel-doc notation warning in net/core/filter.c:
Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new kernel-doc notation warning in sock.h by annotating skc_dontcopy_*
as private fields.
Warning(include/net/sock.h:163): No description found for parameter 'skc_dontcopy_end[0]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.
Substitute the condition to test for _all_ bits being set.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth driver uses the legacy PCI power management, so it has
to do PCI-specific things in its ->suspend() and ->resume() callbacks
and some of them are not done correctly.
Convert forcedeth to the new PCI power management framework and make
it let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested with nVidia Corporation MCP55 Ethernet (rev a2).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts sky2 to new VLAN offload flags control via ethtool.
It also allows for transmit offload of vlan tagged frames which
was not possible before.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver would always try all possible supported speeds even
if the user only asked for a limited set of speed/duplex combinations.
Reported-by: Mohsen Hariri <m.hariri@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the race on bp->stats_pending between the timer and a LINK_UP event
handler.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X
won't be cleared.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes in registers dump:
- Properly calculate dump length for 57712.
- Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
- Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise
Rx hash key won't be available.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call release_firmware() will result in memory leak in
drivers/atm/ambassador.c::ucode_init().
This patch makes sure we always call release_firmware() when needed,
thus removing the leak(s).
Yes, I know checkpatch complains about this patch, but it was either that
or completely mess up the existing style, so I opted to use the existing
style and live with the checkpatch related flak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs()
causes memory leak.
This patch should fix it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
