Fix kernel crash when stifb driver is used with a A1439A CRX (Rattler)
graphics card. (Reference:
http://thread.gmane.org/gmane.linux.ports.hppa/1834)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong pointer type passed into the dev_dbg() function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory size multiplier during detection.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove locking registers after they are unlocked during switch to/from MMIO
mode. This fixes regression on the Blade3D (Trident 9880) caused by the
previous patch (probe fixes).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hitfb presently has probe using __init whilst remove uses __devexit.
As this device can't possibly be hotplugged, switch to __exit and
__exit_p() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Building with CONFIG_DEBUG_SECTION_MISMATCH=y reports:
CC drivers/video/pvr2fb.o
LD drivers/video/built-in.o
WARNING: drivers/video/built-in.o(.text+0xb9b0): Section mismatch in reference from the function pvr2fb_check_var() to the variable .devinit.data:pvr2_fix
The function pvr2fb_check_var() references
the variable __devinitdata pvr2_fix.
This is often because pvr2fb_check_var lacks a __devinitdata
annotation or the annotation of pvr2_fix is wrong.
This is obviously crap as no such reference exists, but it's a bit
closer to reality from older versions which blamed the PCI table. The
real problem was a reference to pvr2_var.vmode from pvr2fb_check_var(),
as pvr2_var is flagged as __devinitdata (pvr2_fix is also, so at least
that part is right).
pvr2_var.vmode is just a fancy way of saying FB_VMODE_NONINTERLACED, so
we just reference that explicitly instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Vertical sync height register can only hold 6 bits. Fix the hsync start test
to use > instead of >=. Also add a few clarifying comments.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though it may not be strictly necessary transp.offset should probably be
0 when alpha channel is not available.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RGB offsets were reversed in 16bpp modes. Simply trying to reverse the
offsets when endianness differs is clearly the wrong thing to do but that is
an issue for another patch.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sm501fb palette code clearly does not handle direct color so change the
driver to use true color visual for 16bpp.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct error paths in probe function.
The probe function enables mmio mode so it important to disable the mmio
mode before exiting the probe function. Otherwise, the console is left in
unusable state (garbled fonts at least, lock up at worst).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/video/built-in.o(.text+0x7c64a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c65d): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c679): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c699): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c69f): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3676): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3689): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36a5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36c5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36cb): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a079a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ad): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07c9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07e9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ef): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
Remove __devinitdata annotation from the variable ypan.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4835/1: Fix stale comment in struct machine_desc description
[ARM] 4829/1: add .get method to pxa-cpufreq to silence a warning
[ARM] 4828/1: fix 3 warnings in drivers/video/pxafb.c
[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c
[ARM] 4826/1: Orion: Register the RTC interrupt on the TS-209
[ARM] pxa: fix clock lookup to find specific device clocks
* Silence a debug output.
* Silence three sparse warnings, one still left.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparently these drivers now need uaccess.h
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the OMAP1 PWL-based LCD backlight driver. It's been in the OMAP
tree for some time. Note that OMAP2 can do similar things with the generic
timers which have PWM outputs. Such timers are more generic than the PWL
found on OMAP1 chips, but have a different EMI profile because they aren't
driven by a pseudorandom number generator.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Avoid driver callbacks when the brightness hasn't changed since
they're not necessary.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Warning is reproducible with selected FB_CFB_REV_PIXELS_IN_BYTE.
CC drivers/video/sysfillrect.o
In file included from drivers/video/sysfillrect.c:18:
drivers/video/fb_draw.h: In function `fb_rev_pixels_in_long':
drivers/video/fb_draw.h:94: warning: no return statement in function returning non-void
CC drivers/video/syscopyarea.o
In file included from drivers/video/syscopyarea.c:22:
drivers/video/fb_draw.h: In function `fb_rev_pixels_in_long':
drivers/video/fb_draw.h:94: warning: no return statement in function returning non-void
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current attr_fgcol_ec / attr_bgcol_ec macros do a simple shift of bits
to get the color from vc_video_erase_char. For a monochrome display
however the attribute does not contain any color, only attribute bits.
Furthermore the reverse bit is lost because it is shifted out, the
resulting color is always 0.
This can bee seen on a monochrome console either directly or by setting it
to inverse mode via "setterm -inversescreen on" . Text is written with
correct color, fb_fillrects from a bit_clear / bit_clear_margins will get
wrong colors.
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure that the default display parameter passed in via the
device's platform data is valid. It turns out when mach-bast.c
was updated, the default_display was set outside of the display
array bounds, causing a panic on startup.
If the default_display is bigger than num_displays, then generate
an error and refuse to initialise the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the initial pattern in the s3c2410 framebuffer driver
to black.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the debugging in the s3c2410 framebuffer driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the S3C2412 to the S3C2410 frame buffer driver
by ensuring that any moved registers can be dealt with.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the console suspend to before we save the state of
the framebuffer to ensure that it does not try and change
the fb state again once we have copied it out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix garbled letters on big endian machines with acceleration enabled.
This makes pm2fb works fine with full acceleration on sparc machine (card
known as Sun PGX-32 or TechSource Raptor GFX-8P).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cleanup sweep:
- Kill ps3fb_priv.xdr_ea and ps3fb_priv.xdr_size, use info->screen_base and
info->fix.smem_len instead.
- Kill superfluous assignments to info->fix.smem_start, info->fix.smem_len,
and info->screen_base in ps3fb_set_par(). Their values never change.
- Add sparse annotations to casts to kill address space warnings
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Round up arbitrary video modes until they fit (if possible)
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorganize modedb handling:
- Reorder the video modes in ps3fb_modedb, for easier indexing using
PS3AV_MODE_* numbers,
- Introduce ps3fb_native_vmode(), to convert from native (PS3AV_MODE_*) mode
numbers to struct fb_videomode *,
- Rename and move ps3fb_default_mode() to ps3fb_vmode().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow all video modes where the visible resolution plus the black borders
matches a native resolution
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frame buffer offsets don't have to be `unsigned long', `unsigned int' is
sufficient
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kill ps3fb_res[], as all information it contains can be obtained in some other
way.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Open-code the X_OFF(), Y_OFF(), WIDTH(), HEIGHT(), and VP_OFF() macros, as
they're used in one place only
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use symbolic names for video modes
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid displaying garbage on unused framebuffers. For most users a single
framebuffer is used together with fbcon. sm501fb supports two framebuffers
where one often is assigned to fbcon and the other one is left unused during
the boot.
The problem here is that framebuffers not in use by fbcon happen to display
garbage. This can easily be solved by making sure that framebuffer memory and
palette ram are cleared.
The problem can be observed by using looking at the panel output (fb1) after
booting the kernel with fbcon on crt (fb0). This is the default
configuration. It's also possible to watch the garbage on the crt framebuffer
by passing "fbcon=map:1" on the kernel cmdline. This will assign fbcon to the
panel (fb1) and leave the crt (fb0) unused.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes it possible to control panel pins usage with flags passed
from the platform data. Without this patch the sm501fb driver always controls
the VBIASEN and FPEN pins. The polarity and use of these pins are very
platform specific, so this patch introduces the flags
SM501FB_FLAG_PANEL_USE_VBIASEN and SM501FB_FLAG_PANEL_USE_FPEN which enable
the use of these pins.
This patch is needed to support the a Sharp LQ104V1DG21 lcd panel on SuperH
platforms such as R2D-1 and R2D-PLUS boards. Letting the sm501fb driver
control the FPEN and VBIASEN pins like today just results in lcd panel
flicker.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pci_get_device does a pci_dev_get, so pci_dev_put needs to be called in an
error case
The problem was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@exists@
type T1,T2;
identifier E;
statement S,S1;
expression x1,x2,x3;
expression test;
int ret != 0;
@@
struct pci_dev *E;
...
(
E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...);
if (E == NULL) S
|
if ((E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...)) == NULL) S
)
... when != pci_dev_put(...,(T1)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
(
if (E == NULL) S1
|
if (test)
+ {
(
+ pci_dev_put(E);
return;
|
+ pci_dev_put(E);
return ret;
)
+ }
|
if (test) {
... when != pci_dev_put(...,(T2)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
+ pci_dev_put(E);
return;
|
+ pci_dev_put(E);
return ret;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some cleanups in uvesafb:
- The custom module_param() get/set functions don't need to be inlined
since it is referred to via a pointer in a struct.
- don't end a #define with a ';'
- remove one of the single quote marks in "''ypan'"
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tdfxfb_setup() can be __init. This fixes the modpost section mismatch
warnings:
WARNING: vmlinux.o(.text+0x4cff9b): Section mismatch: reference to .init.data:mode_option (between 'tdfxfb_setup' and 'getclkMHz')
WARNING: vmlinux.o(.text+0x4cffa8): Section mismatch: reference to .init.data: (between 'tdfxfb_setup' and 'getclkMHz')
[krzysztof.h1@poczta.fm: use __init, not __devinit]
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current nvidiafb_check_var() simply bails out if the selected mode is
out of range of the panel dimensions. A good question would be why the
bogus mode is being selected in the first place -- the panel dimensions
that are read back are certainly bogus, but alas, I have no idea where to
even begin looking at the i2c/EDID/DDC mess:
nvidiafb: Device ID: 10de0165
nvidiafb: CRTC0 analog not found
nvidiafb: CRTC1 analog not found
nvidiafb: EDID found from BUS1
nvidiafb: CRTC 0 is currently programmed for DFP
nvidiafb: Using DFP on CRTC 0
nvidiafb: Panel size is 1280 x 1024
nvidiafb: Panel is TMDS
nvidiafb: unable to setup MTRR
nvidiafb: Flat panel dithering disabled
nvidiafb: PCI nVidia NV16 framebuffer (64MB @ 0xC0000000)
In my .config I presently have:
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_NVIDIA_I2C=y
I've not tried fiddling with these options, as I haven't the vaguest idea
what I should be looking at.
As a workaround, simply groveling for a new mode based on the probed
dimensions seems to work ok. While it would be nice to debug this further
and sort out why the panel information is bogus, I think it's still worth
retrying the mode based on the panel information at hand as a last-ditch
effort, rather than simply bailing out completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__ALIGN_MASK() is an internal implementation detail of ALIGN(). Let's not
needlessly fatten the interface in this driver.
[fujita.tomonori@lab.ntt.co.jp: fix it]
Cc: Alan Hourihane <alanh@fairlite.demon.co.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug identified by Marcio Buss in
http://bugzilla.kernel.org/show_bug.cgi?id=9565 - neofb can overwrite a field
in the fb_info struct.
This fix will result in truncated device identification strings - perhaps
fb_innfo.fix.id can be made larger?
Cc: Marcio Buss <marciobuss@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Christian Trefzer <ctrefzer@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert fb defio from nopage to fault.
Switch from OOM to SIGBUS if the resource is not available.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a sparse warning about symbol 'i' shadowing an earlier one.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pci_get_class implicitly does a pci_dev_put on its second argument, so
pci_dev_put is only needed if there is a break out of the loop.
The semantic match detecting this problem is as follows:
// <smpl>
@@
expression dev;
expression E;
@@
* pci_dev_put(dev)
... when != dev = E
(
* pci_get_device(...,dev)
|
* pci_get_device_reverse(...,dev)
|
* pci_get_subsys(...,dev)
|
* pci_get_class(...,dev)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.text+0xb851a): Section mismatch: reference to .init.text:hpfb_init_one (between 'hpfb_dio_probe' and 'read_null')
hpfb_init_one() must be __devinit since it's called by the __devinit
hpfb_dio_probe().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
geode_modedb[] can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the APUS removal, some code can be removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various instances of
if (!expr & mask)
which should probably have been
if (!(expr & mask))
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compile errors in the xilinxfb, xsysace and uartlite drivers used
by the Xilinx Virtex platform
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
The set_memory_* and set_pages_* family of API's currently requires the
callers to do a global tlb flush after the function call; forgetting this is
a very nasty deathtrap. This patch moves the global tlb flush into
each of the callers
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch converts various users of change_page_attr() to the new,
more intent driven set_page_*/set_memory_* API set.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (54 commits)
MAINTIANERS: just use Mike gmail e-mail for contact and pawn the serial driver off onto Sonic
[Blackfin] arch: remove old I2C BF54x porting.
[Blackfin] arch: Add the semtimedop syscall. Upstream uClibc doesn't compile without it.
[Blackfin] arch: fix bug kernel boot message: memory information is not reasonable
[Blackfin] arch: use common flash driver to setup partitions rather than the bf5xx-flash driver
[Blackfin] arch: Fix bug - kernel build with Debug option enabled fails to boot up
[Blackfin] arch: Fix bug Only RTC interrupt can wake up deeper sleep core.
[Blackfin] arch: Add proper SW System Reset delay sequence
[Blackfin] arch: Update copyright date
[Blackfin] arch: GPIO API cleanup and anomaly update
[Blackfin] arch: Fix BUG gpio_direction_output API is not compatitable with GENERIC_GPIO API interface
[Blackfin] arch: Initial checkin of the memory protection support.
[Blackfin] arch: set_bfin_dma_config shouldnt set SYNC or RESTART by default - add argument or option
[Blackfin] arch: Add some comments - fix semicolons
[Blackfin] arch: move all code related to CPLB handling into a new subdirectory under kernel/
[Blackfin] arch: print out list of modules if kernel is crashing and tell people if the kernel is tainted
[Blackfin] arch: enable generic GPIO based I2C driver in STAMP-BF533, EZKIT-BF533 and EZKIT-BF561 boards
[Blackfin] arch: Don't oops_in_progress if single step is comming from the kernel
[Blackfin] arch: Fix BUG - kernel sometimes would stuck with KEYBOARD_GPIO on
[Blackfin] arch: update to latest anomaly sheets
...
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch disables the VGA text console for AVR32 architecture since
it does not provide the vga.h include file.
AVR32 users should use framebuffer console instead if they need a
console on an attached display.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix line length calculation. var->width is the size of the display in mm. We
like to use the pixel size.
Without this fix, dynamic (fbset) based resolution and depths changes with
s3c2410_fb don't work at all.
Spotted by john cass <johnpcass@yahoo.com>
Signed-off-by: Stefan Schmidt <stefan@openmoko.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9762
Framebuffer is ok only with default parameters only (it is 1280x800-8@60). If
parameters are video=radeonfb:1280x800-32@60 then xres, yres and xres_virtual
are ok but yres_virtual is 1024. It can be corrected by fbset utility so I
think it can be corrected in the driver code also.
Steps to reproduce: video=radeonfb:1280x800-32@60 or
video=radeonfb:1280x800-16@60
Add 1280x800 mode into modedb
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark uvesafb_init_mtrr() as __devinit since its caller is __devinit
and since it accesses __devinitdata.
WARNING: vmlinux.o(.text+0x4df80e): Section mismatch: reference to .init.data: (between 'uvesafb_init_mtrr' and 'uvesafb_show_vbe_ver')
Variable 'blank' cannot be __devinitdata since it is referenced in an
fb_ops method that could be called at any time.
WARNING: vmlinux.o(.text+0x4dfc1e): Section mismatch: reference to .init.data:blank (between 'param_set_scroll' and 'vesa_setpalette')
WARNING: vmlinux.o(.text+0x4dfc24): Section mismatch: reference to .init.data:blank (between 'param_set_scroll' and 'vesa_setpalette')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong pointer type passed into the s3c2410fb_init_registers()
function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the introduction of the acquire_console_sem calls in
0333d83509, kexecing can cause the
kernel to deadlock:
ps3fb_shutdown()
-> unregister_framebuffer()
-> fb_notifier_call_chain(FB_EVENT_FB_UNBIND)
-> fbcon_fb_unbind()
-> unbind_con_driver()
-> bind_con_driver()
[ acquires console_sem ]
-> fbcon_deinit()
-> fbops->fb_release(newinfo, 0)
-> ps3fb_release()
-> ps3fb_sync()
[ acquires console_sem ]
This change avoids the deadlock by moving the acquire_console_sem()
out of ps3fb_sync(), and puts it into the two other callsites, leaving
ps3fb_release() to call ps3fb_sync() without the console semaphore.
[Geert]
- Corrected call sequence above
- ps3fb_release() may be called with and without console_sem held. This is an
inconsistency that should be fixed at the fb level, but for now, try to
acquire console_sem in ps3fb_release().
I think it's safer to let ps3fb_release() try to acquire console_sem and
not refresh the screen if it fails, than to call ps3fb_sync() without
holding console_sem, as ps3fb_par may be modified at the same time, causing
crashes or lockups.
Besides, ps3fb_release() only calls ps3fb_sync() to refresh the screen
when display flipping is disabled, which is an uncommon case (except during
shutdown/kexec).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ps3fb_shutdown, freeing the framebuffer will cause fb_info (in
dev->core.driver_data) to be free()ed, which we potentially access
from the ps3fbd kthread.
This change frees the framebuffer after stopping the ps3fbd kthread.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dev_id arg passed to free_irq() must match that passed to
request_irq().
Fixes this PS3 error message:
Trying to free already-free IRQ 44
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Update for firmware 2.10
As of PS3 firmware version 2.10, the GPU command buffer size must be at least 2
MiB large. Since we use only a small part of the GPU command buffer and don't
want to waste precious XDR memory, move the GPU command buffer back to the
start of the XDR memory reserved for ps3fb and let the unused part overlap with
the actual frame buffer.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds Graphics Output Protocol support to the kernel. UEFI2.0 spec
deprecates Universal Graphics Adapter (UGA) protocol and only Graphics Output
Protocol (GOP) is produced. Therefore, the boot loader needs to query the
UEFI firmware with appropriate Output Protocol and pass the video information
to the kernel. As a result of GOP protocol, an EFI framebuffer driver is
needed for displaying console messages. The patch adds a EFI framebuffer
driver. The EFI frame buffer driver in this patch is based on the Intel Mac
framebuffer driver.
The ELILO bootloader takes care of passing the video information as
appropriate for EFI firmware.
The framebuffer driver has been tested in i386 kernel and x86_64 kernel on EFI
platform.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.
Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.
This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.
Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in fb_ddc_read() is said to be based on the implementation of the
radeon driver:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fc5891c8a3ba284f13994d7bc1f1bfa8283982de
However, comparing the old radeon driver code with the new fb_ddc code
reveals some differences. Most notably, the I2C bus lines are held at the
end of the function, while the original code was releasing them (as the
comment above correctly says.)
There are a few other differences, which appear to be responsible for read
failures on my system. While tracing low-level I2C code in i2c-algo-bit, I
noticed that the initial attempt to read the EDID always failed. It takes
one retry for the read to succeed. As we are about to remove this
automatic retry property from i2c-algo-bit, reading the EDID would really
fail.
As a summary, the I2C lines quirk which is supposedly needed to read EDID
on some older monitors is currently breaking the (first) read on all other
monitors (and might not even work with older ones - did anyone try since
October 2006?)
After applying the patch below, which makes the code in fb_ddc_read()
really similar to what the radeon driver used to have, the first EDID read
succeeds again.
On top of that, as it appears that this code has been broken for one year
now and nobody seems to have complained, I'm curious if it makes sense to
keep this quirk in place. It makes the code more complex and slower just
for the sake of monitors which I guess nobody uses anymore. Can't we just
get rid of it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Roger Leigh <rleigh@whinlatter.ukfsn.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Limit video memory size to avoid crossing a 256 MiB boundary in IOIF space.
- Pass the actual amount of video memory used to lv1_gpu_memory_allocate().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (56 commits)
Blackfin arch: fix bug when enable uart1 with uart0 disabled => no initial console
Blackfin arch: split apart dump_bfin_regs and merge/remove show_regs from process.c, which was largely duplicated
Blackfin arch: use common __INIT/__FINIT defines rather than setting the .section ourselves to .init.text
Blackfin arch: fix bug when sending signals with the wrong PC, cause gdb get confused
Blackfin arch: Ensure we printk out strings with the proper loglevel
Blackfin arch: Need to specify ax with the .init.text section,
Blackfin arch: Update Kconfig to latest Blackfin silicon datasheets
Blackfin arch: update defconfig files
Blackfin arch: Fix typo, and add ENDPROC - no functional changes
Blackfin arch: convert READY to DMA_READY as it causes build errors in common sound code otherwise
Blackfin arch: add defines for the on-chip L1 ROM of BF54x
Blackfin arch: cplb and map header file cleanup
Blackfin arch: cleanup the cplb declares
Blackfin arch: fix broken on BF52x, remove silly checks on processors for L1_SCRATCH defines
Blackfin arch: add support for working around anomaly 05000312
Blackfin arch: cleanup BF54x header file and add BF547 definition
Blackfin arch: fix building for BF542 processors which only have 1 TWI
Blackfin arch: rename _return_from_exception to _bfin_return_from_exception and export it
Blackfin arch: move EXPORT_SYMBOL() to C files where the symbol is actually defined
Blackfin arch: fix bug NOR Flash MTD mount fail
...
... which I've found on a Sapphire X550 (Silent).
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make 'default_mode' and 'default_var' be __initdata.
Fixes these section warnings:
WARNING: vmlinux.o(.data+0x128e0): Section mismatch: reference to .init.data:default_mode_CRT (between 'default_mode' and 'default_var')
WARNING: vmlinux.o(.data+0x128e4): Section mismatch: reference to .init.data:default_var_CRT (between 'default_var' and 'dev_attr_size')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the possible usage of a negative value as an array
index spotted by the Coverity checker.
sisfb_validate_mode() could return a negative error code and we must check for
that prior to using its return value as an array index.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A relatively recent version of the Geode LX datasheet listed the wrong
address for one of the MSRs that controls TFT panels, resulting in
breakage. This patch corrects the MSR address.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attached patch fixes two compilation problems of s1d13xxxfb.c:
- Fixes outdated dbg() message to fix compilation error with debugging enabled.
- Do not read kernel command line options when compiled as module.
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Variables that are only used in #ifdef CONFIG_X86 should also only be
declared there.
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
chipsfb uses PCI interfaces and should depend on PCI.
CC drivers/video/chipsfb.o
drivers/video/chipsfb.c: In function 'chipsfb_pci_init':
drivers/video/chipsfb.c:378: error: implicit declaration of function 'pci_request_region'
drivers/video/chipsfb.c:435: error: implicit declaration of function 'pci_release_region'
make[2]: *** [drivers/video/chipsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
!CONFIG_PCI causes the build to fail.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size passed to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyberpro: when user requests 16bpp, use it and not 24bpp.
There was a missing break causing requests for 16bpp mode
to end up in 24bpp mode.
Signed-off-by: Jan Rinze Peterzon <janrinze@home.nl>
Acked-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove warning from powerpc ppc64_defconfig builds:
drivers/video/aty/radeon_pm.c:30: warning: 'radeon_reinitialize_M10' declared 'static' but never defined
It's used only under CONFIG_PM, and only with CONFIG_X86 before it is
defined, so the forward declaration can be moved under the ifdef.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix FB_OMAP dependencies so that the OMAP FB driver options are presented
correctly.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(pointer > 0) is deeply weird; (pointer >= 0) is even dumber...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* ssh://master.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-x86: (33 commits)
x86: convert cpuinfo_x86 array to a per_cpu array
x86: introduce frame_pointer() and stack_pointer()
x86 & generic: change to __builtin_prefetch()
i386: do not BUG_ON() when MSR is unknown
x86: acpi use cpu_physical_id
x86: convert cpu_llc_id to be a per cpu variable
x86: convert cpu_to_apicid to be a per cpu variable
i386: introduce "used_vectors" bitmap which can be used to reserve vectors.
x86: use raw locks during oopses
x86: honor _PAGE_PSE bit on page walks
i386: do cpuid_device_create() in CPU_UP_PREPARE instead of CPU_ONLINE.
x86: implement missing x86_64 function smp_call_function_mask()
x86: use descriptor's functions instead of inline assembly
i386: consolidate show_regs and show_registers for i386
i386: make callgraph use dump_trace() on i386/x86_64
x86: enable iommu_merge by default
i386: i386 add AMD64 Barcelona PMU MSR definitions to msr.h
x86: Unify i386 and x86-64 early quirks
x86: enable HPET on ICH3 and ICH4
x86: force enable HPET on VT8235/8237 chipsets
...
Manually fix trivial conflict with task pid container helper changes in
arch/x86/kernel/process_32.c
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes errors and warnings pointed out by the checkpatch.pl
script.
Antonino Daplas replaced BIT with ENCODE_BIT.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cyber2000fb, rename BIT macro
BIT will be global macro for (1 << x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpu_data is currently an array defined using NR_CPUS. This means that
we overallocate since we will rarely really use maximum configured cpus.
When NR_CPU count is raised to 4096 the size of cpu_data becomes
3,145,728 bytes.
These changes were adopted from the sparc64 (and ia64) code. An
additional field was added to cpuinfo_x86 to be a non-ambiguous cpu
index. This corresponds to the index into a cpumask_t as well as the
per_cpu index. It's used in various places like show_cpuinfo().
cpu_data is defined to be the boot_cpu_data structure for the NON-SMP
case.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has not been any serious user of this ill conceived thing since the
original invention in like '95 so I recently deleted this from everywhere
except the last instance in logo.c. This patch removes the last two
instances in logo.c. They conditions were not useful anyway as when
compiled in they would always evaluate as true.
Last not least this is necessary to get the SGI IP22 and DECstation kernels
to compile again.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build broken by accaa24c49:
CC drivers/video/console/newport_con.o
drivers/video/console/newport_con.c: In function 'newport_show_logo':
drivers/video/console/newport_con.c:111: error: assignment of read-only location
drivers/video/console/newport_con.c:111: warning: assignment makes integer from pointer without a cast
drivers/video/console/newport_con.c:112: error: assignment of read-only location
drivers/video/console/newport_con.c:112: warning: assignment makes integer from pointer without a cast
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove rogue default m in drivers/video/Kconfig
default m is near always wrong, like here. For some reason ACPI
likes to reintroduce these and I like to immediately squash them again
before they pollute too many .configs.
Cc: len.brown@intel.com
Cc: luming.yu@gmail.com
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
Remove magic macros for screen_info structure members
[x86] remove uses of magic macros for boot_params access
Other/Some pr_*() macros are already defined in kernel.h, but pr_err() was
defined multiple times in several other places
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a test in tgafb_mono_imageblit() for a colour image with a fall-back
to cfb_imageblit(). The test is not necessary as the only caller, which is
tgafb_imageblit(), checks it too and only invokes this function for monochrome
images. It looks like a left-over from before some changes to
tgafb_imageblit().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pixel mask calculation in tgafb_mono_imageblit() uses a variable
left-shift on a 32-bit data type by up to 32. Shifting by the width of a data
type or more produces an unpredictable result according to the C standard.
Rather than widening the data type this fix makes sure the count is between 0
and 31. The reason is not to penalise 32-bit platforms with operation on a
"long long" type for a marginal case that is meant not to happen (blitting an
image of a zero width).
The reason it has escaped for so long is the Alpha, being purely 64-bit, :-)
does not mask the shift out to 32 bits. This is a valid implementation --
producing the correct result certainly falls within "unpredictable behaviour".
It does trigger on MIPS though and it is the recent merge of the TC support
which only enabled the driver for use on anything other than the Alpha. For
MIPS when the width is 32 the mask ends up being 0 rather than 0xffffffff as
it should be and the frame buffer is not updated.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported in Bugzilla Bug 9093, upon switching to X, a small rectangular
cursor can still be seen blinking in the upper left part of the screen. It is
fbcon's text cursor. This is caused by a strange ioctl(..., KDSETMODE,
KD_TEXT) call done by something in userspace, perhaps by X itself, while the
tty is still in graphics mode. And when the tty is in KD_TEXT mode, the
cursor timer is restarted.
Although this is a userspace problem, we can work around it by delaying the
restart of the cursor timer until an fbcon_switch() is called. In other
words, the cursor timer will not be restarted even if a KD_TEXT mode switch is
requested.
Regression potential: Present but low
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This correct case, when source and destination X coordinates difference is n
multiple of pixels in byte. This is probably rare case, but this case should
supported for completeness.
Reorganization of FB_READL and FB_WRITEL calls results in code size decrease
for normal build without swapping support and size with support enabled is
reasonable too.
[adaplas]
Add missing fb_rev_pixels_in_long() prototype.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds check if selected pixclock is valid (is in the PLL range).
Previously, if the pixclock could not be set, the new mode resolution was set
but pixclock was not set which led to incorrect timings sent to monitor.
[adaplas]
Fixed a few misplaced curly braces.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection matching algorithm. It allows to choose
mode with matching depth even when requested color lengths are greater than
color lengths of every mode with requested color depth.
It also fixes bug in s3fb - wrong error value returned when format is not
supported by chip.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the extern declaration for global_mode_option to <linux/fb.h> and rename
the variable to fb_mode_option.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Enhance horizontal panning on firmware 1.90 and up:
- On firmware 1.90 and up, L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT supports copying
rectangles from XDR to DDR memory with different source and destination
line lengths. Hence larger horizontal virtual resolutions can be supported
(up to 16368 pixels).
- As the actual frame buffer memory layout no longer matches the entries in
ps3fb_res[], create fake struct ps3fb_ioctl_res data for the
PS3FB_IOCTL_SCREENINFO ioctl, so user space applications that depend on it
keep on working.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Add virtual screen and panning support:
- The vertical virtual screen size is limited by the amount of memory
reserved for ps3fb,
- The horizontal virtual screen size is limited to the fullscreen width,
- Advertise that we support panning, so fbcon will use it if the virtual
screen is enabled.
Enabling a virtual screen (using `fbset -vyres nnn') can speed up text
console scrolling by a factor of 10-15, depending on the video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't keep the borders for non-fullscreen modes in XDR memory:
- Extract ps3fb_sync_image()
- Work around the alignment restrictions of L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT
by using an offset with L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP
- Only copy the visible part of the screen on every vblank
- Always put the real frame buffer at the start of video memory
- Clear fullscreen DDR memory on mode change
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Use fb_info.par properly:
o Move mode-specific fields into struct ps3fb_par
o Allocate struct ps3fb_par using framebuffer_alloc()
o Protect access to ps3fb_par in ps3fb_sync() using the console semaphore
(this semaphore is already held when ps3fb_set_par() is called)
o Avoid calling ps3av_set_video_mode() if the actual video mode hasn't
changed
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: In the case of non-fullscreen video modes, there was a partial overlap
of the GPU command buffer and the frame buffer. Fix and cleanup various issues
with overlap and alignment:
- Move the GPU command buffer from the beginning to the end of video memory
- Exclude the GPU command buffer from the actual frame buffer memory
- Align the start of the virtual frame buffer to PAGE_SIZE instead of to 64
KiB, and don't waste memory if it's already aligned (for fullscreen modes)
- Take into account the alignment when checking memory requirements and
maximum number of frames
- Make sure fb_fix_screeninfo.smem_start always points to the virtual frame
buffer start, so we don't have to compensate for that in ps3fb_mmap()
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make ps3fb_wait_for_vsync() and ps3fb_flip_ctl() static, as they're no
(longer) used outside ps3fb.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up includes
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not print warnings on invalid frame numbers, as this can be triggered from
user space.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX frame-buffer read operation should be faster for all configurations
then drawing each individual character again in response to scroll events.
The nonstandard fields allows to configure frame-buffer special options flags
for different display configurations by board specific initialization code.
One of such specific options is reversed order of pixels in each individual
byte. i.MX frame-buffer seems to be designed for big-endian use first. The
byte order is correctly configured for little-endian ordering, but if 1, 2 or
4 bits per pixel are used, pixels ordering is incompatible to Linux generic
frame-buffer drawing functions.
The patch "Allow generic BitBLT functions to work with swapped pixel order in
bytes" introduces required functionality into FBDEV core. The pixels ordering
selection has to be enabled at compile time CONFIG_FB_CFB_REV_PIXELS_IN_BYTE
and for each display configuration which requires it by flag
FB_NONSTD_REV_PIX_IN_B in "nonstd" field of info structure.
This patch provides way for board specific code to select this option.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
don't distinguish between `boot' and `non-boot' autodetection now the
autodetection code has been improved
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move AGP and DRM menus into the video graphics support menu.
They use 'menuconfig' so that they can all be disabled with
one selection.
Make the console menu use 'menuconfig' so that it can all be
disabled with one selection.
Make the frame buffer menu use 'menuconfig' so that it can all be
disabled with one selection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add logo.nologo kernel boot option to disable the logo in order to provide
more screen space for kernel messages; especially useful when debugging and
screen space is more critical.
newport_con driver changes are untested.
[akpm@linux-foundation.org: cleanups, coding-style fixes]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add error messages to the probe call.
[adaplas]
On failure, return actual error value instead of -ENXIO.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the i2c ports are to be reversed, I2C_CLASS_HWMON assignment must also be
reversed.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various console drivers are able to resize the screen via the con_resize()
hook. This hook is also visible in userspace via the TIOCWINSZ, VT_RESIZE and
VT_RESIZEX ioctl's. One particular utility, SVGATextMode, expects that
con_resize() of the VGA console will always return success even if the
resulting screen is not compatible with the hardware. However, this
particular behavior of the VGA console, as reported in Kernel Bugzilla Bug
7513, can cause undefined behavior if the user starts with a console size
larger than 80x25.
To work around this problem, add an extra parameter to con_resize(). This
parameter is ignored by drivers except for vgacon. If this parameter is
non-zero, then the resize request came from a VT_RESIZE or VT_RESIZEX ioctl
and vgacon will always return success. If this parameter is zero, vgacon will
return -EINVAL if the requested size is not compatible with the hardware. The
latter is the more correct behavior.
With this change, SVGATextMode should still work correctly while in-kernel and
stty resize calls can expect correct behavior from vgacon.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move video graphics driver configs to fix menus:
Fix FB_PMAGB_B to depend on FB so that the FB menus remain
listed in order and indented correctly.
Fix FB_IBM_GXT4500 to depend on FB so that the FB menus remain
listed in order and indented correctly.
The OMAP FB drivers still muck up the FB menu a bit, so I put
OMAP drivers at the end of the FB menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel FB: allow odd- and even-field-first in interlaced modes, and
proper sync to vertical retrace
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel FB: the chip adds two halflines automatically in interlaced mode,
force even line count for the right timings.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add error messages to the probe call.
While they may rarely trigger, they may be useful when something weird is
going on. Also this is good style.
[akpm@linux-foundation.org: remove unneeded initialisation]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make radeonfb work ith the 200m Xpress RC410. In my tests it was terribly
unstable and would freeze until I set a refresh rate in the kernel argument
to 75.
e.g video=radeonfb:1280x800@75
Now it is rock solid.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a missing FB dependency to FB_PMAGB_B.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors pointed by the checkpatch.pl script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with the cpu_relax() call. This makes
scrolling faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with the cpu_relax() call. This makes
scrolling faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces busy waiting with cpu_relax() call. This makes scrolling
faster.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Add a `mode' parameter to ps3fb_get_res_table(), as in some cases it
should check the full-screen flag of the _new_ video mode instead of the
current video mode.
This bug caused spurious mode change failures when switching between
fullscreen and non-fullscreen modes using fbset, while ps3-video-mode worked
fine.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow generic frame-buffer code to correctly write texts and blit images for
1, 2 and 4 bit per pixel frame-buffer organizations when pixels in bytes are
organized to in opposite order than bytes in long type.
Overhead should be reasonable. If option is not selected, than compiler
should eliminate completely all overhead.
The feature is disabled at compile time if CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is
not set.
[adaplas]
Convert helper functions to macros if feature is not enabled.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few nvidia hardware where the i2c port assignments are reversed,
i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c
port to the primary display. In most cases, if only 1 display is attached, or
if only 1 flatpanel and 1 analog display is attached, the port reversal is of
no consequence. However if 2 flatpanels are attached, it can cause display
problems.
There is no sane way of determining if the hardware reversed the i2c port
assignment, so the simplest fix is to add a boot/module option, "reverse_i2c
to explicitly reverse the i2c port.
This also restores i2c ordering back to the pre-2.6.22 state.
Signed-off-by: Antonino Daplas <adaplas@gail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, if the refresh rate is not specified, fb_find_mode() returns the
first known video mode with the requested resolution, which provides no
guarantees wrt the refresh rate. Change this so that the mode with the
highest refresh rate is returned when the driver provides a custom video mode
database and the monitor limits, and a mode with the safe 60 Hz refresh rate
otherwise.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel framebuffer now supports interlaced video modes.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed things:
1. vmalloc()/vfree() replaced with rvmalloc()/rvfree() (taken from
drivers/media/video/se401.c)
2. mmap method implemented (mostly taken from drivers/media/video/se401.c)
3. smem_start and smem_len fields of struct fb_fix_screeninfo initialized.
(smem_start initialized with virtual address, don't know if it is really
bad...)
[adaplas: sparse warning fix]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- disallows setting of virtual height above 2048 as it does
not work for accelerated copyarea and imageblit
- fixes blinking of pm2v cursor by pushing cursor outside
the display (x=2047)
- fixes hardware cursor position on Permedia 2 chips with
panning enabled
- enables hardware cursor by default
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support for the Permedia 2 chip.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes:
- redundant fields from the cirrusfb_regs structure
- one redundant header
- fixes two includes ("" to <>)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch does some "short-range" code improvements like merging identical
switch clauses, replacing conditional branches with calculation of values,
merging only once-used functions into place they are called from.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused or redundant fields from cirrusfb_info structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces "typedef enum" with "enum type" constructs. Using the
typedef is error for the checkpatch.pl script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes over 850 errors and warnings pointed out by the checkpatch.pl
script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection to always prefer default mode if possible
and always honor type of display set by default mode settings.
This patch is required in case the same display modes were defined for
different panels (e.g. STN and TFT).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- moves more display mode preparations to s3c2410fb_check_var()
- reduces number of fields in s3c2410fb_info
- removes redundant values setting in s3c2410fb_probe()
- removes static mach_info pointer
- releases fb_info structure in s3c2410fb_remove()
- changes s3c2410fb_init to __init from __devinit
- fixes few typos in comments and removes unused includes
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces <asm/uaccess.h> with <linux/uaccess.h> after the
checkpatch.pl hint. The include of <asm/uaccess.h> is removed if the driver
does not use it.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akpm's patch "newport_con warning fix" got me to look at the console drivers
again and one thing that I noticed was that none of the fonts was using ISO
initializers for it's fonts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atyfb: Move the pseudo palette into the card-specific atyfb_par, so it's no
longer shared among multiple cards
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch sets correct bits related to the byte ordering of the
framebuffer. This was tested on little endian kernel only. The big endian
kernel may require different settings.
The patch also adds 32 bpp mode which is called 24 bpp by Samsung. One
pixel takes 32 bits but only 24 bits are used in this mode.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds missing virtual register offsets where
appropriate. This fixes crashes in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon2 and lcdcon3 register value
from the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds synchronization pulse lenght fields to
the s3c2410fb_display structure and makes use of them
in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes use of vertical margins fields in
the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon3 register from the
s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes use of margins fields in the s3c2410fb_display
structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new structure to describe and handle
more than one panel (display mode) for the s3c2410 framebuffer.
This structure is added after the pxafb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes redundant fb field from
the s3c2410fb_info structure. This breaks circular
reference fb_info -> s3c2410fb_info -> fb_info again.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up the driver a bit. It contains
coding style fixes (pointed by Lindent and checkpatch),
white space clean ups and few minor code improvements.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support to the pm3fb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support for Permedia 2V chips.
The hardware cursor is disabled by default. It does not blink - the
same issue is mentioned in the x11 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Looking at the code flow, `int first' in fb_create_modedb() should be static.
[adaplas]
Better for 'int first' to be moved outside the loop.
[akpm@linux-foundation.org: kill stray semicolon]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors detected by checkpatch.pl script in the pm3fb.c
file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors detected by checkpatch.pl script in the pm2fb.c
file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
