When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The check when DRAM interleaving is enabled should be done against the
pvt->dram_IntlvSel field and not against the ->dram_limit.
Simplify first loop and fixup printk formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already
right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the
values to the left 8 bits is wrong.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where
i in (0..7) are both bits 39-24 and therefore the shifting should be
done by 24 and not by 8.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allocate memory statically for 8-node machines max for simplicity
instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds.
Spotted by Jan Beulich.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add support for change_pte mmu notifiers
KVM: MMU: add SPTE_HOST_WRITEABLE flag to the shadow ptes
KVM: MMU: dont hold pagecount reference for mapped sptes pages
KVM: Prevent overflow in KVM_GET_SUPPORTED_CPUID
KVM: VMX: flush TLB with INVEPT on cpu migration
KVM: fix LAPIC timer period overflow
KVM: s390: fix memsize >= 4G
KVM: SVM: Handle tsc in svm_get_msr/svm_set_msr correctly
KVM: SVM: Fix tsc offset adjustment when running nested
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Clear sticky FSR register after saving it to func parametr
microblaze: UMS is used only for MMU kernel
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: using HZ needs an include of linux/param.h
sparc32: convert to asm-generic/hardirq.h
sparc64: Cache per-cpu %pcr register value in perf code.
sparc64: Fix comment typo in perf_event.c
sparc64: Minor coding style fixups in perf code.
sparc64: Add a basic conflict engine in preparation for multi-counter support.
sparc64: Increase vmalloc size to fix percpu regressions.
sparc64: Add initial perf event conflict resolution and checks.
sparc: Niagara1 perf event support.
sparc: Add Niagara2 HW cache event support.
sparc: Support all ultra3 and ultra4 derivatives.
sparc: Support HW cache events.
In virtual environments (namely, Xen Dom0) virt <-> phys and
virt <-> isa-bus translations cannot be freely interchanged (and
even outside such environments it is not really correct to do so).
When looking at memory below 1M, the latter translations should
always be used.
iscsi_ibft_find.c part from: Martin Wilck <martin.wilck@ts.fujitsu.com>.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <ketuzsezs@darnok.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Run generate-cmdlist.sh properly
perf_event: Clean up perf_event_init_task()
perf_event: Fix event group handling in __perf_event_sched_*()
perf timechart: Add a power-only mode
perf top: Add poll_idle to the skip list
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: Remove overly verbose "switch to high res mode" message
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kmemtrace: Fix up tracer registration
tracing: Fix infinite recursion in ftrace_update_pid_func()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix rename of pt_regs offset defines breakage
m68knommu: remove duplicated #include
m68knommu: show KiB rather than pages in "Freeing initrd memory:" message
Previous patch d63678d607d0e37ec7abe5ceb545d7e8aab956a4 clear
it for noMMU kernel. This one do it for MMU.
Correct noMMU version
Signed-off-by: Michal Simek <monstr@monstr.eu>
This reverts commit 6029336426.
Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm skipping -rc2 because the -rc1 Makefile mistakenly said -rc2, so in
order to avoid confusion, I'm jumping from -rc1 to -rc3. That way, when
'uname' (or an oops report) says 2.6.32-rc2, there's no confusion about
whether people perhaps meant -rc1 or -rc2.
* 'acpi-pad' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi_pad: build only on X86
ACPI: create Processor Aggregator Device driver
Fixup trivial conflicts in MAINTAINERS file.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: EC: Don't parse DSDT for EC early init on Compal
ACPI: EC: Rewrite DMI checks
ACPI: dock: fix "sibiling" typo
ACPI: kill overly verbose "throttling states" log messages
ACPI: Fix bound checks for copy_from_user in the acpi /proc code
ACPI: fix bus scanning memory leaks
ACPI: EC: Restart command even if no interrupts from EC
sony-laptop: Don't unregister the SPIC driver if it wasn't registered
sony-laptop: remove _INI call at init time
sony-laptop: SPIC unset IRQF_SHARED, set IRQF_DISABLED
sony-laptop: remove device_ctrl and the SPIC mini drivers
If i2c device probing fails, then there is no driver to dereference
after calling i2c_new_device(). Stop assuming that probing will always
succeed, to avoid NULL pointer dereferences. We have an easier access
to the driver anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Tim Shepard <shep@alum.mit.edu>
Cc: Colin Leroy <colin@colino.net>
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The ab3100 driver doesn't, so there is no
point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
The I2C_CLIENT_INSMOD macro is only useful for i2c drivers which
implement device detection. The tsl2561 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The leds-pca9532 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
There is no point in implementing a detect callback for the MAX6875, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This basically divides the binary module size by 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Some times ago the eeprom and max6875 drivers moved to
drivers/misc/eeprom, but their documentation did not follow. It's
finally time to get rid of Documentation/i2c/chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
Revert "Seperate read and write statistics of in_flight requests"
cfq-iosched: don't delay async queue if it hasn't dispatched at all
block: Topology ioctls
cfq-iosched: use assigned slice sync value, not default
cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
cfq-iosched: implement slower async initiate and queue ramp up
cfq-iosched: delay async IO dispatch, if sync IO was just done
cfq-iosched: add a knob for desktop interactiveness
Add a tracepoint for block request remapping
block: allow large discard requests
block: use normal I/O path for discard requests
swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
fs/bio.c: move EXPORT* macros to line after function
Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
cciss: fix build when !PROC_FS
block: Do not clamp max_hw_sectors for stacking devices
block: Set max_sectors correctly for stacking devices
cciss: cciss_host_attr_groups should be const
cciss: Dynamically allocate the drive_info_struct for each logical drive.
cciss: Add usage_count attribute to each logical drive in /sys
...
We cannot delay for the first dispatch of the async queue if it
hasn't dispatched at all, since that could present a local user
DoS attack vector using an app that just did slow timed sync reads
while filling memory.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
this is needed for kvm if it want ksm to directly map pages into its
shadow page tables.
[marcelo: cast pfn assignment to u64]
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
this flag notify that the host physical page we are pointing to from
the spte is write protected, and therefore we cant change its access
to be write unless we run get_user_pages(write = 1).
(this is needed for change_pte support in kvm)
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When using mmu notifiers, we are allowed to remove the page count
reference tooken by get_user_pages to a specific page that is mapped
inside the shadow page tables.
This is needed so we can balance the pagecount against mapcount
checking.
(Right now kvm increase the pagecount and does not increase the
mapcount when mapping page into shadow page table entry,
so when comparing pagecount against mapcount, you have no
reliable result.)
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The number of entries is multiplied by the entry size, which can
overflow on 32-bit hosts. Bound the entry count instead.
Reported-by: David Wagner <daw@cs.berkeley.edu>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
It is possible that stale EPTP-tagged mappings are used, if a
vcpu migrates to a different pcpu.
Set KVM_REQ_TLB_FLUSH in vmx_vcpu_load, when switching pcpus, which
will invalidate both VPID and EPT mappings on the next vm-entry.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
commit 628eb9b8a8
KVM: s390: streamline memslot handling
introduced kvm_s390_vcpu_get_memsize. This broke guests >=4G, since this
function returned an int.
This patch changes the return value to a long.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running nested we need to touch the l1 guests
tsc_offset. Otherwise changes will be lost or a wrong value
be read.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When svm_vcpu_load is called while the vcpu is running in
guest mode the tsc adjustment made there is lost on the next
emulated #vmexit. This causes the tsc running backwards in
the guest. This patch fixes the issue by also adjusting the
tsc_offset in the emulated hsave area so that it will not
get lost.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
