Cleanup receive buffer allocation and management,
Add more error handling checks from PHY and bump version.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Expand the returned data for ethtool debug access to include
all of the mapped PCI area; except for the small set of registers
that are for diagnostic RAM access. Access to those registers
will hang the system.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge of four previous patches and the Kconfig fix
* Remove debug printk's
* whitespace cleanup and version number change
* clear interrupts, reset phy, and reset hardware on shutdown
* ignore 64bit counter overflow interrupts
* fix a couple of places where second port could clobber state
of first port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.
Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to handle receive and transmit packet arbiter timeouts.
Transmit arbiter timeouts happens when Gigabit sends to 100Mbit port
on same switch and pause occurs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cleanup messages (for debug) about PHY interrrupts, because when
user can't get driver working that is often the problem.
Use a consistent way of enabling interrupts by port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove support for the non-Broadcom genesis based boards. The code
is untested, and probably won't work as is. The newer boards are all
Yukon based, and only old Genesis board I can find uses Broadcom.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove the bits and pieces added relating to Yukon II chipset.
The Yukon 2 will be in a separate driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Replace inline accessor functions for chip revision and number of ports
with simple structure members.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The inlines and macro's needed some cleanup's and fixes:
* change name of macro SKGEMAC_REG to SK_REG to better reflect usage
and fix comments
* ditto for SK_GEXM_REG -> SK_XMAC_REG and SKGEGMA_REG -> SK_GMA_REG
* change skge_gm_ to just gm_ since it is just a local function and long
names look ugly.
* change skge_xm_ to just xm_
* fix xm_write32 to write as two u16's with correct byte order
* fix xm_outaddr to correctly use offset
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
