When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.
However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.
If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:
irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq(): c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000
Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Comparing to PATCH v1, because clk_debugfs_init is included in
"#if defined CONFIG_DEBUG_FS", we only need to check NULL return.
Thanks Li Zefan <lizf@cn.fujitsu.com>
debugfs_create_u8() and other function's return value's checking method are
also fixed in this patch.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix these compiler warnings:
gpmc.c: In function 'gpmc_init':
gpmc.c:432: warning: 'return' with a value, in function returning void
gpmc.c:439: warning: 'return' with a value, in function returning void
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2.6.28-rc tightened up the ELF architecture checks on ARM. For
non-EABI it only allows VFP if the hardware supports it. However,
the kernel fails to also inspect the soft-float flag, so it
incorrectly rejects binaries using soft-VFP.
The fix is simple: also check that EF_ARM_SOFT_FLOAT isn't set
before rejecting VFP binaries on non-VFP hardware.
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_board_info array was filled incorrectly.
Due to circumstances, the way it is filled works.
This patch fills array properly.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mx31ads_defconfig compilation failed with
arch/arm/mach-mx3/mx31ads.c: In function 'mxc_init_imx_uart':
arch/arm/mach-mx3/mx31ads.c:102: error: 'mxc_uart_device0' undeclared (first use in this function)
arch/arm/mach-mx3/mx31ads.c:102: error: (Each undeclared identifier is reported only once
arch/arm/mach-mx3/mx31ads.c:102: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-mx3/mx31ads.o] Error 1
Add missing include
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Data register holds the value we have written to a gpio. To
get the input value we must read the Pad Status Register MX3 (or Sample
Status register in MX1/2 terms)
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compilation of sharpsl_pm when CONFIG_PM in unselected.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
The arch dependent function ftrace_mcount_set was only used by the daemon
start up code. This patch removes it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ftrace daemon is complex and can cause nasty races if something goes
wrong. Since it affects all of the kernel, this patch disables dynamic
ftrace from any arch that depends on the daemon. Until the archs are
ported over to the new MCOUNT_RECORD method, I am disabling dynamic
ftrace from them.
Note: I am leaving in the arch/<arch>/kernel/ftrace.c code alone since
that can be used when the arch is ported to MCOUNT_RECORD. To port
the arch to MCOUNT_RECORD, the scripts/recordmcount.pl needs to be
updated. I will make that easier to do for 2.6.29. For 28, we will keep
the archs disabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Those inline assembly segments using the umlal instruction must have
the & modifier so to be sure that a purely input register won't alias
one of the registers used as input+output. In most cases, the inputs
are still used after the outputs are touched, and most binutil versions
insist on "rdhi, rdlo and rm must all be different" even for ARMv6+.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A typo caused these values to be swapped leading to incorrect memory
type attributes.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
The "5298/1: Drop desc_handle_irq()" patch went overboard
and deleted an essential line of code, causing all AT91
GPIO interrupts to oops (in irq). Trimmed example:
Unable to handle kernel NULL pointer dereference at virtual address 000000c4
...
PC is at gpio_irq_handler+0x78/0xd0
LR is at gpio_irq_handler+0x38/0xd0
...
Backtrace:
[<c0029884>] (gpio_irq_handler+0x0/0xd0) from [<c0020054>] (__exception_text_start+0x54/0x7c)
[<c0020000>] (__exception_text_start+0x0/0x7c) from [<c00209ec>] (__irq_svc+0x2c/0x60)
Exception stack(0xc1c1de00 to 0xc1c1de48)
[<c01f4ca8>] (_spin_unlock_irq+0x0/0x3c) from [<c01389f8>] (at91ether_open+0x220/0x318)
[<c01387d8>] (at91ether_open+0x0/0x318) from [<c018caa4>] (dev_open+0xa8/0x10c)
[<c018c9fc>] (dev_open+0x0/0x10c) from [<c018b874>] (dev_change_flags+0x98/0x164)
[<c018b7dc>] (dev_change_flags+0x0/0x164) from [<c0019f8c>] (ip_auto_config+0x164/0xe28)
[<c0019e28>] (ip_auto_config+0x0/0xe28) from [<c0020318>] (__exception_text_end+0x60/0x180)
[<c00202b8>] (__exception_text_end+0x0/0x180) from [<c0008738>] (kernel_init+0x70/0xd8)
[<c00086c8>] (kernel_init+0x0/0xd8) from [<c00398e0>] (do_exit+0x0/0x6ac)
This patch restores the missing line'o'code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The baseband cpu owns the pmic, so voltage regulator control is only
available via a relatively limited interface through the proc_comm
transport.
Signed-off-by: Brian Swetland <swetland@google.com>
San:
- Propagate DM errors to the originator of the request.
- Implement msm_dmov_stop_cmd()
- Add return value to init code
- Modify msm_dmov_stop_cmd() to support ungraceful flushing
Arve:
- Disable datamover interrupt when not in use.
We turn off the interrrupt to allow power collapse from idle.
Signed-off-by: San Mehat <san@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
- Add some more peripherals (sdcc, etc) to the iomap.
- Remove virtual base addresses for devices that we should be passing
physical addresses to drivers via resources and ioremap()ing.
- don't try to use uarts for ll debug once the mmu is enabled due to
problems with the peripheral window
- make base addresses void __iomem * and fixup irq.c and timer.c
- Remove common.c and bring in devices.c/devices.h similar to
the PXA architecture.
Signed-off-by: Brian Swetland <swetland@google.com>
The proc_comm protocol is the lowest level protocol available for
communicating with the modem core. It provides access to clock and
power control, among other things, and is safe for use from atomic
contexts, unlike the higher level SMD and RPC transports.
Signed-off-by: Brian Swetland <swetland@google.com>
The MSM architecture covers a wider family of chips than just the MSM7X00A.
Move to a more generic name, in perparation for supporting the specific
SoC variants as sub-architectures (ARCH_MSM7X01A, ARCH_MSM722X, etc). This
gives us ARCH_MSM for the (many) common peripherals.
This also removes the unused/obsolete config item MSM7X00A_IDLE.
Signed-off-by: Brian Swetland <swetland@google.com>
This patch fixes the section mismatch warning from
sa1111.o at buildtime.
CC arch/arm/common/sa1111.o
LD arch/arm/common/built-in.o
LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x87f4): Section mismatch in reference from the function sa1111_probe() to the function .devinit.text:sa1110_mb_enable()
The function sa1111_probe() references
the function __devinit sa1110_mb_enable().
This is often because sa1111_probe lacks a __devinit
annotation or the annotation of sa1110_mb_enable is wrong.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent changes have been made to use the generic SPI-based ads7846
touch screen driver and a generic SPI-based corgi-type LCD/backlight
driver. Update the {corgi,spitz}_defconfig to favor the use of these
drivers instead of the legacy ones.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.
This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit 68677ab3d0.
A smoother migration path would be making corgi_ts.c and other drivers
depending on corgi_ssp.c and corgi_lcd.c to depend on BROKEN instead,
and still allows those to exist around for some time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
