The datasheet specifies a 3uS pause after performing a software
reset. The default implementation of genphy_soft_reset() does not
provide this, so implement soft_reset with the needed pause.
Signed-off-by: Esben Haabendal <eha@deif.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two sockmap fixes: i) fix a potential warning when a socket with
pending cork data is closed by freeing the memory right when the
socket is closed instead of seeing still outstanding memory at
garbage collector time, ii) fix a NULL pointer deref in case of
duplicates release calls, so make sure to only reset the sk_prot
pointer when it's in a valid state to do so, both from John.
2) Fix a compilation warning in bpf_prog_attach_check_attach_type()
by moving the function under CONFIG_CGROUP_BPF ifdef since only
used there, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2018-04-08
Here's one important Bluetooth fix for the 4.17-rc series that's needed
to pass several Bluetooth qualification test cases.
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.
The example flows, as it is in mlxsw:
1) driver load/asic probe:
mlxsw_core
-> mlxsw_sp_resources_register
-> mlxsw_sp_kvdl_resources_register
-> devlink_resource_register IDX
mlxsw_spectrum
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
2) reload triggered by devlink command:
-> mlxsw_devlink_core_bus_device_reload
-> mlxsw_sp_fini
-> mlxsw_sp_kvdl_fini
-> devlink_resource_occ_get_unregister IDX
(struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
which is using mlxsw_sp would cause use-after free)
-> mlxsw_sp_init
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
Fixes: d9f9b9a4d0 ("devlink: Add support for resource abstraction")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current (mildly evil) fsl_pq_mdio code uses an undocumented shadow of
the TBIPA register on LS1021A, which happens to be read-only.
Changing TBI PHY address therefore does not work on LS1021A.
The real (and documented) address of the TBIPA registere lies in the eTSEC
block and not in MDIO/MII, which is read/write, so using that fixes
the problem.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a simpler and generic method for for finding (and mapping)
the TBIPA register.
Instead of relying of complicated logic for finding the TBIPA register
address based on the MDIO or MII register block base
address, which even in some cases relies on undocumented shadow registers,
a second "reg" entry for the mdio bus devicetree node specifies the TBIPA
register.
Backwards compatibility is kept, as the existing logic is applied when
only a single "reg" mapping is specified.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon says:
====================
ibmvnic: Fix driver reset and DMA bugs
This patch series introduces some fixes to the driver reset
routines and a patch that fixes mistakes caught by the kernel
DMA debugger.
The reset fixes include a fix to reset TX queue counters properly
after a reset as well as updates to driver reset error-handling code.
It also provides updates to the reset handling routine for redundant
backing VF failover and partition migration cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the ibmvnic driver after a partition migration occurs
there is no requirement to do a reset of the main CRQ. The current
driver code does the required re-enable of the main CRQ, then does
a reset of the main CRQ later.
What we should be doing for a driver reset after a migration is to
re-enable the main CRQ, release all the sub-CRQs, and then allocate
new sub-CRQs after capability negotiation.
This patch updates the handling of mobility resets to do the proper
work and not reset the main CRQ. To do this the initialization/reset
of the main CRQ had to be moved out of the ibmvnic_init routine
and in to the ibmvnic_probe and do_reset routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a failover case for a non-redundant pseries VNIC
configuration that was not being handled properly. The current
implementation assumes that the driver will always have a redandant
device to communicate with following a failover notification. There
are cases, however, when a non-redundant configuration can receive
a failover request. If that happens, the driver should wait until
it receives a signal that the device is ready for operation.
The driver is agnostic of its backing hardware configuration,
so this fix necessarily affects all device failover management.
The driver needs to wait until it receives a signal that the device
is ready for resetting. A flag is introduced to track this intermediary
state where the driver is waiting for an active device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if the driver is waiting for a reset following
a device parameter change, failure to schedule a reset can result
in a hang since a completion signal is never sent.
If the device configuration is being altered by a tool such
as ethtool or ifconfig, it could cause the console to hang
if the reset request does not get scheduled. Add some additional
error handling code to exit the wait_for_completion if there is
one in progress.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter that tracks used TX descriptors pending completion
needs to be zeroed as part of a device reset. This change fixes
a bug causing transmit queues to be stopped unnecessarily and in
some cases a transmit queue stall and timeout reset. If the counter
is not reset, the remaining descriptors will not be "removed",
effectively reducing queue capacity. If the queue is over half full,
it will cause the queue to stall if stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some mistakes caught by the DMA debugger. The first change
fixes a unnecessary unmap that should have been removed in an
earlier update. The next hunk fixes another bad unmap by zeroing
the bit checked to determine that an unmap is needed. The final
change fixes some buffers that are unmapped with the wrong
direction specified.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4b2e6877b8 ("tipc: Fix namespace violation in tipc_sk_fill_sock_diag")
tried to fix the crash but failed, the crash is still 100% reproducible
with it.
In tipc_sk_fill_sock_diag(), skb is the diag dump we are filling, it is not
correct to retrieve its NETLINK_CB(), instead, like other protocol diag,
we should use NETLINK_CB(cb->skb).sk here.
Reported-by: <syzbot+326e587eff1074657718@syzkaller.appspotmail.com>
Fixes: 4b2e6877b8 ("tipc: Fix namespace violation in tipc_sk_fill_sock_diag")
Fixes: c30b70deb5 (tipc: implement socket diagnostics for AF_TIPC)
Cc: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com>
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: fix uninit-values in networking stack
It seems syzbot got new features enabled, and fired some interesting
reports. Oh well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported __skb_try_recv_from_queue() was using skb->peeked
while it was potentially unitialized.
We need to clear it in __skb_clone()
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported :
BUG: KMSAN: uninit-value in rtnh_ok include/net/nexthop.h:11 [inline]
BUG: KMSAN: uninit-value in fib_count_nexthops net/ipv4/fib_semantics.c:469 [inline]
BUG: KMSAN: uninit-value in fib_create_info+0x554/0x8d20 net/ipv4/fib_semantics.c:1091
@remaining is an integer, coming from user space.
If it is negative we want rtnh_ok() to return false.
Fixes: 4e902c5741 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported :
BUG: KMSAN: uninit-value in alg_bind+0xe3/0xd90 crypto/af_alg.c:162
We need to check addr_len before dereferencing sa (or uaddr)
Fixes: bb30b8848c ("crypto: af_alg - whitelist mask and type")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we delete a u32 key via u32_delete_key(), we forget to
call idr_remove() to remove its handle from IDR.
Fixes: e7614370d6 ("net_sched: use idr to allocate u32 filter handles")
Reported-by: Marcin Kabiesz <admin@hostcenter.eu>
Tested-by: Marcin Kabiesz <admin@hostcenter.eu>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED2[2]/INTn pin on Marvell 88E1318S as well as 88E1510/12/14/18 needs
to be configured to be usable as interrupt not only when WOL is enabled,
but whenever we rely on interrupts from the PHY.
Signed-off-by: Esben Haabendal <eha@deif.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-06
This series contains a couple of fixes for the new ice driver.
Wei Yongjun fixes the return error code for error case during init.
Anirudh fixes the incorrect use of ARRAY_SIZE() in the ice ethtool code
and fixed "for" loop calculations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Return correct size from ice_get_regs_len.
2) Fix incorrect use of ARRAY_SIZE in ice_get_regs.
Fixes: fcea6f3da5 (ice: Add stats and ethtool support)
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix to return error code ICE_ERR_NO_MEMORY from the alloc error
handling case instead of 0, as done elsewhere in this function.
Fixes: dc49c77236 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At the end of ip6_forward(), IPSTATS_MIB_OUTFORWDATAGRAMS and
IPSTATS_MIB_OUTOCTETS are incremented immediately before the NF_HOOK call
for NFPROTO_IPV6 / NF_INET_FORWARD. As a result, these counters get
incremented regardless of whether or not the netfilter hook allows the
packet to continue being processed. This change increments the counters
in ip6_forward_finish() so that it will not happen if the netfilter hook
chooses to terminate the packet, which is similar to how IPv4 works.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohammed Gamal says:
====================
hv_netvsc: Fix shutdown issues on older Windows hosts
Guests running on WS2012 hosts would not shutdown when changing network
interface setting (e.g. Number of channels, MTU ... etc).
This patch series addresses these shutdown issues we enecountered with WS2012
hosts. It's essentialy a rework of the series sent in
https://lkml.org/lkml/2018/1/23/111 on top of latest upstream
====================
Fixes: 0ef58b0a05 ("hv_netvsc: change GPAD teardown order on older versions")
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers to netvsc_revoke_*_buf() and netvsc_teardown_*_gpadl()
already have their net_device instances. Pass them as a paramaeter to
the function instead of obtaining them from netvsc_device struct
everytime
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit 0cf737808a ("hv_netvsc: netvsc_teardown_gpadl() split")
the call sequence in netvsc_device_remove() was as follows (as
implemented in netvsc_destroy_buf()):
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Teardown receive buffer GPADL
3- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
4- Teardown send buffer GPADL
5- Close vmbus
This didn't work for WS2016 hosts. Commit 0cf737808a
("hv_netvsc: netvsc_teardown_gpadl() split") rearranged the
teardown sequence as follows:
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
3- Close vmbus
4- Teardown receive buffer GPADL
5- Teardown send buffer GPADL
That worked well for WS2016 hosts, but it prevented guests on older hosts from
shutting down after changing network settings. Commit 0ef58b0a05
("hv_netvsc: change GPAD teardown order on older versions") ensured the
following message sequence for older hosts
1- Send NVSP_MSG1_TYPE_REVOKE_RECV_BUF message
2- Send NVSP_MSG1_TYPE_REVOKE_SEND_BUF message
3- Teardown receive buffer GPADL
4- Teardown send buffer GPADL
5- Close vmbus
However, with this sequence calling `ip link set eth0 mtu 1000` hangs and the
process becomes uninterruptible. On futher analysis it turns out that on tearing
down the receive buffer GPADL the kernel is waiting indefinitely
in vmbus_teardown_gpadl() for a completion to be signaled.
Here is a snippet of where this occurs:
int vmbus_teardown_gpadl(struct vmbus_channel *channel, u32 gpadl_handle)
{
struct vmbus_channel_gpadl_teardown *msg;
struct vmbus_channel_msginfo *info;
unsigned long flags;
int ret;
info = kmalloc(sizeof(*info) +
sizeof(struct vmbus_channel_gpadl_teardown), GFP_KERNEL);
if (!info)
return -ENOMEM;
init_completion(&info->waitevent);
info->waiting_channel = channel;
[....]
ret = vmbus_post_msg(msg, sizeof(struct vmbus_channel_gpadl_teardown),
true);
if (ret)
goto post_msg_err;
wait_for_completion(&info->waitevent);
[....]
}
The completion is signaled from vmbus_ongpadl_torndown(), which gets called when
the corresponding message is received from the host, which apparently never happens
in that case.
This patch works around the issue by restoring the first mentioned message sequence
for older hosts
Fixes: 0ef58b0a05 ("hv_netvsc: change GPAD teardown order on older versions")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split each of the functions into two for each of send/recv buffers.
This will be needed in order to implement a fine-grained messaging
sequence to the host so that we accommodate the requirements of
different Windows versions
Fixes: 0ef58b0a05 ("hv_netvsc: change GPAD teardown order on older versions")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing network interface settings, Windows guests
older than WS2016 can no longer shutdown. This was addressed
by commit 0ef58b0a05 ("hv_netvsc: change GPAD teardown order
on older versions"), however the issue also occurs on WS2012
guests that share NVSP protocol versions with WS2016 guests.
Hence we use Windows version directly to differentiate them.
Fixes: 0ef58b0a05 ("hv_netvsc: change GPAD teardown order on older versions")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boundary check in mvpp2_prs_init_from_hw must be done according to the
passed "tid" parameter, not the mvpp2_prs_entry index, which is not yet
initialized at the time of the check.
Fixes: 47e0e14eb1 ("net: mvpp2: Make mvpp2_prs_hw_read a parser entry init function")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arp_filter performs an ip_route_output search for arp source address and
checks if output device is the same where the arp request was received,
if it is not, the arp request is not answered.
This route lookup is always done on main route table so l3slave devices
never find the proper route and arp is not answered.
Passing l3mdev_master_ifindex_rcu(dev) return value as oif fixes the
lookup for l3slave devices while maintaining same behavior for non
l3slave devices as this function returns 0 in that case.
Fixes: 613d09b30f ("net: Use VRF device index for lookups on TX")
Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: better validate user provided tunnel names
This series changes dev_valid_name() to not attempt reading
a possibly too long user-provided device name, then use
this helper in five different tunnel providers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: ed1efb2aef ("ipv6: Add support for IPsec virtual tunnel interfaces")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use valid_name() to make sure user does not provide illegal
device name.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use dev_valid_name() to validate tunnel names,
so better use strnlen(name, IFNAMSIZ) than strlen(name) to make
sure to not upset KASAN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code refactoring
from Luis as he attempts to wrangle that codebase into something that is
managable, along with a bunch of userspace tests for it. Other than
that, a handful of small bugfixes and reverts of things that didn't work
out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSiGg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylPpACgyEKOur8rwp/3uBRxqhoFeWp1RtAAoIvlMjn6
MQ8LIeHNLRnpqGX5L78L
=93HA
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code
refactoring from Luis as he attempts to wrangle that codebase into
something that is managable, along with a bunch of userspace tests for
it. Other than that, a handful of small bugfixes and reverts of things
that didn't work out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
drivers: base: remove check for callback in coredump_store()
mt7601u: use firmware_request_cache() to address cache on reboot
firmware: add firmware_request_cache() to help with cache on reboot
firmware: fix typo on pr_info_once() when ignore_sysfs_fallback is used
firmware: explicitly include vmalloc.h
firmware: ensure the firmware cache is not used on incompatible calls
test_firmware: modify custom fallback tests to use unique files
firmware: add helper to check to see if fw cache is setup
firmware: fix checking for return values for fw_add_devm_name()
rename: _request_firmware_load() fw_load_sysfs_fallback()
test_firmware: test three firmware kernel configs using a proc knob
test_firmware: expand on library with shared helpers
firmware: enable to force disable the fallback mechanism at run time
firmware: enable run time change of forcing fallback loader
firmware: move firmware loader into its own directory
firmware: split firmware fallback functionality into its own file
firmware: move loading timeout under struct firmware_fallback_config
firmware: use helpers for setting up a temporary cache timeout
firmware: simplify CONFIG_FW_LOADER_USER_HELPER_FALLBACK further
drivers: base: add description for .coredump() callback
...
Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs. 91k
remvoed), thanks to finally being able to delete the IRDA drivers and
networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful of
new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSnAA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn60ACgxKvU/5XBP14hBkBpAcD0Q43OHe0AniEti65M
Kw03GWK3NNM3pzk49BjZ
=sj3K
-----END PGP SIGNATURE-----
Merge tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
