In case of an instruction processing damage (IPD) machine check in kernel mode
the resulting action is always to stop the kernel. This is not necessarily
the best solution since a retry of the failing instruction might succeed. Add
logic to retry the instruction if no more than 30 instruction processing
damage checks occured in the last 5 minutes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added some changes that where proposed by Andrew Morton. Added 3592 device
type.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work. The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8. When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page. That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state. The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state. Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate. Note: To get such an unformatted device online
it has to be re-analyzed. This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown. Use
memory pool instead. (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Interrupts can stay disabled if an error occurred in _chp_add(). Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a race condition in the I/O termination logic. The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this fixes coverity id #489.
Since the last element in the array is always ARRAY_SIZE-1 we have to check
for ipcnum >= ARRAY_SIZE()
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If compiled into the kernel, parport_register_driver() is called before the
parport driver has been initalised.
This means that it is expected that tp_count is 0 after the
parport_register_driver() call() - tipar's attach function will not be
called until later during bootup.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
Some drivers like to use request_irq() to find an unused interrupt slot.
- Use it in i82365.c
- Kill unused SA_PROBE.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] update sn2 defconfig
[IA64] Add mca recovery failure messages
[IA64-SGI] fix SGI Altix tioce_reserve_m32() bug
[IA64] enable dumps to capture second page of kernel stack
[IA64-SGI] - Reduce overhead of reading sn_topology
[IA64-SGI] - Fix discover of nearest cpu node to IO node
[IA64] IOC4 config option ordering
[IA64] Setup an IA64 specific reclaim distance
[IA64] eliminate compile time warnings
[IA64] eliminate compile time warnings
[IA64-SGI] SN SAL call to inject memory errors
[IA64] - Fix MAX_PXM_DOMAINS for systems with > 256 nodes
[IA64] Remove unused variable in sn_sal.h
[IA64] Remove redundant NULL checks before kfree
[IA64] wire up compat_sys_adjtimex()
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] PCI quirk: VIA IRQ fixup should only run for VIA southbridges
[PATCH] PCI: fix potential resource leak in drivers/pci/msi.c
[PATCH] PCI: Documentation: no more device ids
[PATCH] PCI: fix via irq SATA patch
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
[PATCH] USB: ftdi_sio: add support for ASK RDR 400 series card reader
[PATCH] USB: ftdi_sio: Adds support for iPlus device.
[PATCH] USB: ftdi_sio vendor code for RR-CirKits LocoBuffer USB
[PATCH] USB: Use new PCI_CLASS_SERIAL_USB_* defines
[PATCH] USB: net2280: set driver data before it is used
[PATCH] USB: net2280: check for shared IRQs
[PATCH] USB: net2280: send 0-length packets for ep0
[PATCH] USB: net2280: Handle STALLs for 0-length control-IN requests
[PATCH] USB: storage: atmel unusual dev update
[PATCH] USB: Storage: unusual devs update
[PATCH] USB: add new iTegno usb CDMA 1x card support for pl2303
[PATCH] USB: Resource leak fix for whiteheat driver
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).
This should address that. I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The coverity checker spotted (as entry #599) that we might leak `entry' in
drivers/pci/msi.c::msix_capability_init()
This patch should take care of that.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for stack overflow in EventDescriptionStr, (a function
for debuging firmware events). We allocated 50 bytes on local stack
for buff[], however there are places in the code where we've attempted
copying in greater than 50 bytes into buff[].
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some versions of the IBM 2104-DU3 disk enclosure
have been observed to hang Inquiries to non zero
LUNs to the SES device. This device only has LUN 0,
so this patch adds it to the BLIST to prevent scsi
core from scanning beyond LUN 0.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some pioneer DVDs are apparently returning odd "not ready" status
codes that the mid-layer doesn't recognise and so passes back to the
user as errors.
This patch overhauls our not-ready handling and adds transparent retries for:
format in progress
rebuild in progress
recalculation in progress
operation in progress
Long write in progress
self test in progress
The Pioneer was actually returning "long write in progress"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for an ASK RDR 400 series contactless card
reader <http://www.ask.fr/uk/products_and_services/terminals.html> to
the ftdi_sio driver's device ID table. The product ID was supplied by
Adriano Couto on the ftdi-usb-sio-devel list.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support in ftdi_sio usbserial driver for USB modems sold by
Plus GSM Company in Poland.
Signed-off-by: Luiz Fernando Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds recognition of the RR-CirKits LocoBuffer USB
to the existing FTDI driver. http://www.rr-cirkits.com
Signed-off-by: Nathan Bronson <ngb@sns-usa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could use the recently added PCI_CLASS_SERIAL_USB_UHCI,
PCI_CLASS_SERIAL_USB_OHCI and PCI_CLASS_SERIAL_USB_EHCI defines in
more places, for slightly shorter and clearer code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as671) fixes a bug in the error pathway for the net2280
probe routine. A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as669) fixes a bug in the net2280 driver. Now it will
properly send zero-length packets on ep0 until the control status stage
occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as668) fixes a typo in net2280. The handler for 0-length
control-IN requests should check that the endpoint _isn't_ halted before
sending a 0-length packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally submitted by Olivier Blondeau <zeitoun@gmail.com>, with re-diffing
by me. Adds a new atmel unusual_dev entry.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
This patch removes the Protocol portion of the Iomega Click! device as it's not
needed. Not-needed message reported by Kenneth Crudup <kenny@panix.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new iTegno usb CDMA 1x card (usbid '0eba:2080') support to pl2303 driver
Signed-off-by: Wang Jun <wangjun1974@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We may return from drivers/usb/serial/whiteheat.c::whiteheat_attach()
without freeing `result' if we leave via the no_firmware: label.
Spotted by the coverity checker as #670
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
For coping with bad keyboards, permit to type a braille pattern by
pressing several chords. By default, only one chord is needed.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix resource leak in
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c::ahc_linux_pci_dev_probe()
Found by the coverity checker (#668)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.
The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only. This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] MAINTAINERS
[PARISC] Make ioremap default to _nocache
[PARISC] Add new entries to the syscall table
[PARISC] Further work for multiple page sizes
[PARISC] Fix up hil_kbd.c mismerge
[PARISC] defconfig updates
[PARISC] Document that we tolerate "Relaxed Ordering"
[PARISC] Misc. janitorial work
[PARISC] EISA regions must be mapped NO_CACHE
[PARISC] OSS ad1889: Match register names with ALSA driver
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia/pcmcia_resource.c: fix crash when using Cardbus cards
[PATCH] vrc4171: update config
[PATCH] pcmcia: fix oops in static mapping case
[PATCH] pcmcia: remove unneeded forward declarations
[PATCH] pcmcia: do not set dev_node to NULL too early
[PATCH] pcmcia: fix comment for pcmcia_load_firmware
[PATCH] pcmcia: unload second device first
[PATCH] pcmcia: add new ID to pcnet_cs
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Fix define_machine so machine_is() works from modules
powerpc/ppc: export strncasecmp
[PATCH] powerpc: fix oops in alsa powermac driver
[PATCH] powerpc: update {g5,iseries,pseries}_defconfigs
[PATCH] ppc: Fix powersave code on arch/ppc
[PATCH] powerpc/cell: remove BUILD_BUG_ON and add sys_tee to spu_syscall_table
[PATCH] powermac: Fix i2c on keywest based chips
[PATCH] powerpc: Lower threshold for DART enablement to 1GB
[PATCH] powerpc: IOMMU support for honoring dma_mask
This patch contains the following possible cleanups:
- make the following needlessly global function static:
- drm_bufs.c: drm_addbufs_fb()
- remove the following unused EXPORT_SYMBOL's:
- drm_agpsupport.c: drm_agp_bind_memory
- drm_bufs.c: drm_rmmap_locked
- drm_bufs.c: drm_rmmap
- drm_stub.c: drm_get_dev
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
I recently found that not all BIOS manufacturers are using the specified
generic PNP id in their TPM ACPI table entry. I have added the vendor
specific IDs that I know about and added a module parameter that a user can
specify another HID to the probe list if their device isn't being found by the
default list.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a boolean module parameter that allows the user to turn
interrupt support on and off. The default behavior is to attempt to use
interrupts.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __devexit_p() for the exit/remove function to protect against
discarding it.
WARNING: drivers/char/tpm/tpm_infineon.o - Section mismatch: reference to .exit.text:tpm_inf_pnp_remove from .data between 'tpm_inf_pnp' (at offset 0x20) and 'tpm_inf'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The acpi table which contains the BIOS log events was updated for 1.2.
There are now client and server modes as defined in the specifications with
slightly different formats. Additionally, the start field was even too
small for the 1.1 version but had been working anyway. This patch updates
the code to deal with any of the three types of headers probperly (1.1, 1.2
client and 1.2 server).
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory start and length values obtained from the ACPI entry need to be
checked and filled in with the default values from the specification if
they don't exist. This patch fills in the default values and uses them
appropriately.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apply the latest changes in the TPM interface to the Infineon TPM-driver.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Acked-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use set_bit() and clear_bit() for dev_mask manipulation.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The timeout and duration values used in the tpm driver are not exposed to
userspace. This patch converts the storage units to jiffies with
msecs_to_jiffies. They were always being used in jiffies so this
simplifies things removing the need for calculation all over the place.
The change necessitated a type change in the tpm_chip struct to hold
jiffies.
Signed-off-by: Kylie Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver for the next generation of TPM chips version 1.2 including support
for interrupts. The Trusted Computing Group has written the TPM Interface
Specification (TIS) which defines a common interface for all manufacturer's
1.2 TPM's thus the name tpm_tis.
Signed-off-by: Leendert van Doorn <leendert@watson.ibm.com>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
This updated version of the patch breaks the multi-value sysfs file into
separate files pointed out by Greg. It also addresses the code redundancy and
ugliness in the tpm_show_* functions pointed out on another patch by Dave
Hansen.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the TPM 1.2 Specification, each command is classified as short, medium or
long and the chip tells you the maximum amount of time for a response to each
class of command. This patch provides and array of the classifications and a
function to determine how long the response should be waited for. Also, it
uses that information in the command processing to determine how long to poll
for. The function is exported so the 1.2 driver can use the functionality to
determine how long to wait for a DataAvailable interrupt if interrupts are
being used.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes in the 1.2 TPM Specification make it necessary to update some fields
of the chip structure in the initialization function after it is registered
with tpm.c thus tpm_register_hardware was modified to return a pointer to the
structure. This patch makes that change and the associated changes in
tpm_atmel and tpm_nsc. The changes to tpm_infineon will be coming in a patch
from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To assist with chip management and better support the possibility of having
multiple TPMs in the system of the same kind, the struct tpm_vendor_specific
member of the tpm_chip was changed from a pointer to an instance. This patch
changes that declaration and fixes up all accesses to the structure member
except in tpm_infineon which is coming in a patch from Marcel Selhorst.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many of the sysfs files were calling the TPM_GetCapability command with array.
Since for 1.2 more sysfs files of this type are coming I am generalizing the
array so there can be one array and the unique parts can be filled in just
before the command is called.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch set contains numerous changes to the base tpm driver
(tpm.c) to support the next generation of TPM chips. The changes include new
sysfs files because of more relevant data being available, a function to
access the timeout and duration values for the chip, and changes to make use
of those duration values. Duration in the TPM specification is defined as the
maximum amount of time the chip could take to return the results. Commands
are in one of three categories short, medium and long. Also included are
cleanups of how the commands for the sysfs files are composed to reduce a
bunch of redundant arrays.
This patch:
Fix minor spacing issues.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A string corresponding to the tcpa_pc_event_id POST_CONTENTS was missing
causing an overflow bug when access was attempted in the get_event_name
function.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The eventname was kmalloc'd and not freed in the *_show functions.
This bug was found by Coverity.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
from: Greg Howard <ghoward@sgi.com>
Fix Altix system controller (snsc) device names to include the slot number
of the blade whose associated system controller is the target of the device
interface. Including the slot number avoids a problem we're currently
having where slots within the same enclosure are attempting to create
multiple kobjects with identical names.
Signed-off-by: Greg Howard <ghoward@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a possible Oops in the Siemens Gigaset base driver when the device is
unplugged while an ISDN connection is still active, and makes sure that the
isdn4linux link level (LL) is properly informed if a connection is broken
by the USB cable being unplugged.
- Avoid unsafe checks of URB status fields outside the URB completion
handlers, keep track of in-use URBs myself instead.
- If an isochronous transfer URB completes with status==0, also check the
status of the frame descriptors.
- Verify length of interrupt messages received from the device.
- Align the length limit on transmitted AT commands with the device
documentation.
- In case of AT response receive overrun, keep newly arrived instead of old
unread data.
- Remove redundant check of device ID in the USB probe function.
- Correct and improve some comments and formatting.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using the old ioctl interface together with cardbus card gives a NULL
pointer dereference since cardbus devices don't have a struct pcmcia_device.
also s->io[0].res can be NULL as well.
Fix is to move the pcmcia code after the cardbus code and to check for a null
pointer.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch updates "depends on" for PCMCIA_VRC4171.
CONFIG_VRC4171 has been removed, so replace it with CPU_VR41XX && ISA.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As static maps do not have IO resources, this setting oopses. However, as
we do not ever read this value, we can safely remove it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If we set dev_node to NULL too early, some drivers which used this to
determine whether unregister_netdev() needs to be called fail when removing
a PCMCIA card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The comment of "pcmcia_load_firmware" is wrong: the
firmware(*.cis) files reside in /lib/firmware/ _not_
/lib/firmware/cis/ .
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use list_add instead of list_add_tail for pcmcia_device_add
so that second device of multi-function-card will be unloaded first.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This means "DMA Read returns" can bypass "MMIO Writes".
Violating the PCI specs in this case improves outbound DMA "flows"
and is currently not required by any drivers.
This is NOT a new behavior. Previous chipsets did this
already and I believe ZX1 PDC was already setting this
for hpux. I just want to further document the behavior.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an oops in 2.6.16.X when loading the snd_powermac module. The
name of the requested module changed during the 2.6.16 development cycle
from i2c-keylargo to i2c-powermac.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a test to detect the ICH7 based Core Duo SONY laptops (such as the SZ1)
as type3 models.
Signed-off-by: Arnaud MAZIN < arnaud.mazin@gmail.com>
Acked-by: Stelian Pop <stelian@poppies.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix for bug #6395:
Fail to resume on Tecra M2 with ADM1032 and Intel 82801DBM
The BIOS of the Tecra M2 doesn't like it when it has to reboot or resume
after the i2c-i801 driver has left the SMBus in PEC mode. The most simple
fix is to clear the PEC bit after after every transaction. That's what
this driver was doing up to 2.6.15 (inclusive).
Thanks to Daniele Gaffuri for the very good report.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the MSI-K8T-NEO2 FIR ( Athlon-64, Socket 939 with VIA-K8T800- Chipset
and onboard Sound,... ) the BIOS lets you choose "DISABLED" or "AUTO" for
the On-Board Sound Device.
If you add another PCI-Sound-Card the BIOS disables the on-board device.
So far I have a Quirk, that does set the correspondent BIT in the
PCI-registers to enable the soundcard.
But how to ensure that the code is executed ONLY on excactly this kind of
boards (not any other with similar Chipset)?
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During module unloading, cdev_del() must be called to unmap cdev related
kobject references and other cleanups(such as inode->i_cdev being set to
NULL) which prevents the OOPS upon subsequent loading, usage and unloading
of modules(as seen in the mail thread
http://marc.theaimsgroup.com/?l=linux-kernel&m=114533640609018&w=2).
Also, remove unneeded test of gpio_base.
Signed-off-by: Thayumanavar Sachithanantham <thayumk@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
WARNING: drivers/video/pm2fb.o - Section mismatch: reference
to .init.data: from .text after 'pm2fb_set_par' (at offset 0xd5d)
WARNING: drivers/video/pm2fb.o - Section mismatch: reference
to .init.data: from .text after 'pm2fb_set_par' (at offset 0xd82)
They are caused because pm2fb_set_par() uses lowhsync and lowvsync which
are marked __devinitdata.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix ahc_pci_write_config's (wrong order of arguments).
Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/megaraid.c: In function `mega_internal_command':
drivers/scsi/megaraid.c:4474: warning: unused variable `flags'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes coverity bug id #480. Since id_array is declared as
id_array[MAX_SLOTS], the check for i>MAX_SLOTS is obviously false.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Contains the following misc fixes:
- Fix build warnings
- Race condition in lpfc_workq_post_event() could corrupt phba->work_list.
- nlp_sid was not being initialized properly
- Fix some RSCN handling during the re-discovery after Link Up event.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Additional fixes to LOGO, PLOGI, and RSCN processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix cleanup code in the lpfc_pci_probe_one() error code path.
This changes the original patch by:
- hardsetting the return value from lpfc_pci_probe_one() to
-ENODEV (negative value) if we fail attach
- removes the checks from lpfc_pci_remove_one() validating the
host and phba pointers as it's no longer needed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed FC protocol violation in handling of PRLO.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that hit nodev_tmo during discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The room for the names in bcm43xx_priv_wx_args[] are IFNAMSIZ long and
IFNAMSIZ is defined as 16, so the names in bcm43xx_priv_wx_args should
be 15 characters (16 including the trailing \0). This patch fixes that
for the "set_shortpreambl", "get_shortpreambl", "set_swencryption", and
"get_swencryption" private calls. Patch is against 2.6.17-rc1.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the bcm43xx sysfs code and makes it compliant
with the unwritten sysfs rules (at least I hope so).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "depends on" to make all bcm43xx driver options be listed
at the same level.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:456: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:460: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:476: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:480: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:200: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:311: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:733: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbol firmware F3.91-71 has an additional word in the commsquality RID.
Extend the receiving buffer by one word to accomodate it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.17-rc1 changed the title for the entry CONFIG_NET_RADIO. I
personally disagree with this change and want it reverted. Patch for
2.6.17-rc1.
Rationale : WIRELESS_EXT is an invisible option. Therefore,
the only way for a user to enable it is via NET_RADIO. Some users need
to do that for out-of-tree drivers. Therefore it should be mentionned
in the title of the option.
Rationale2 : the option just below is called "Wireless
Extension API over RtNetlink". Some users may confuse this option for
the main "Wireless Extension" option. Therefore reverting this change
help disambiguate the relation between those two options.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send scan completion events to user space when a scan completes.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airo firmware versions >= 5.30.17 send re-association events to the
driver that are currently unrecognized, causing spurious disassociation
events to be sent to user space. Loss of sync due to scan requests also
results in disassociation events sent to user space. This patch traps
those two events; suppressing sync-loss on scan, and sending the correct
association event on re-association notifications.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global mthca_update_rate() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only check that RMPP version is not specified when MAD class does not
support RMPP. Just because a class is allowed to use RMPP doesn't
mean that rmpp_version needs to be set for the MAD agent to
register. Checking this was a recent change which was too pedantic.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort succeeds, then the aborted request should to be
removed from the list of pending requests. This fixes list corruption
after an abort occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix return code of fb_write():
If at least 1 byte was transferred to the device, return number of bytes,
otherwise:
- return -EFBIG - if file offset is past the maximum allowable offset or
size is greater than framebuffer length
- return -ENOSPC - if size is greater than framebuffer length - offset
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Marking radeon_pci_register() as __devinit clears up all section
mismatch warnings that are caused by radeon_pci_register() calling
various __devinit function. Is there some reason not to do this?
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x628)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x6b5)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x6bd)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text:radeon_probe_screens from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x7d6)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text:radeon_check_modes from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x7e5)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the following section mismatch:
WARNING: drivers/video/savage/savagefb.o - Section mismatch: reference to .init.data: from .text.savagefb_probe after 'savagefb_probe' (at offset 0x5e2)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From http://bugzilla.kernel.org/show_bug.cgi?id=6358
The alim15x3.c havn't been update for 3 years. Recently when we use this
"ULI M1573" south bridge chip found that can't mount CDROM(VCD) smoothly,
must waiting for a long time. After I check the "ULI M1573" south bridge
datasheet, I found the reason. The reason is the "ULI M1573" version in
the Linux is "0xC7" not "0xC4" anymore So I was modified the source than it
was successed.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noted by Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the IDE device on ATI SB600
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wording of two messages in drivers/pnp/manager.c is incorrect. Fix that.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix all modpost section mismatch warnings in parport_pc:
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x230)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x283)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x3e6)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x400)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x463)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x488)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:superios from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x54c)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x56a)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x67)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x9f)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0xa7)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:cards from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x132)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x142)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was looking into random driver code and found a suspicious looking
memcpy() in drivers/char/ipmi/ipmi_bt_sm.c on 2.6.17-rc1:
if ((size < 2) || (size > IPMI_MAX_MSG_LENGTH))
return -1;
...
memcpy(bt->write_data + 3, data + 1, size - 1);
where sizeof bt->write_data is IPMI_MAX_MSG_LENGTH. It looks like the
memcpy would overflow by 2 bytes if size == IPMI_MAX_MSG_LENGTH. A patch
attached to limit size to (IPMI_MAX_LENGTH - 2).
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc complains about __devinit in the wrong location:
drivers/char/ipmi/ipmi_si_intf.c:2205: warning: '__section__' attribute does not apply to types
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are places in the kernel where we look up files in fd tables and
access the file structure without holding refereces to the file. So, we
need special care to avoid the race between looking up files in the fd
table and tearing down of the file in another CPU. Otherwise, one might
see a NULL f_dentry or such torn down version of the file. This patch
fixes those special places where such a race may happen.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the bitmasks used when writing to the M41T00 registers.
The original code used a mask of 0x7f when writing to each register,
this is incorrect and probably the result of a copy-paste error. As a
result years from 1980 to 1999 will be read back as 2000 to 2019.
Signed-off-by: David Barksdale <amatus@ocgnet.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the EXPORT_SYMBOL_GPL of the static function cpufreq_parse_governor().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
The previous patch had bugs (locking and refcount).
This one could also be related to the latest DELL reports.
But they only slip into this if a user prog (e.g. powersave daemon does when
AC got (un) plugged due to a scheme change) echos something to
/sys/../cpufreq/scaling_governor
while the frequencies got limited by BIOS.
This one works:
Subject: Max freq stucks at low freq if reduced by _PPC and sysfs gov access
The problem is reproducable by(if machine is limiting freqs via BIOS):
- Unplugging AC -> max freq gets limited
- echo ${governor} >/sys/.../cpufreq/scaling_governor (policy->user_data.max
gets overridden with policy->max and will never come up again.)
This patch exchanged the cpufreq_set_policy call to __cpufreq_set_policy and
duplicated it's functionality but did not override user_data.max.
The same happens with overridding min/max values. If freqs are limited and
you override the min freq value, the max freq global value will also get
stuck to the limited freq, even if BIOS allows all freqs again.
Last scenario does only happen if BIOS does not reduce the frequency
to the lowest value (should never happen, just for correctness...)
drivers/cpufreq/cpufreq.c | 17 +++++++++++++++--
1 files changed, 15 insertions(+), 2 deletions(-)
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Richard Purdie
Move platform_scoop_config from the SharpSL scoop PCMCIA driver to
the SCOOP driver. This avoids build failures when PCMCIA is not built
or is modular (scoop.c itself cannot be modular).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Fix further issues in drivers/char/drm/via_irq.c
drivers/char/drm/drm_memory.c: possible cleanups
drm: deline a few large inlines in DRM code
drm: remove master setting from add/remove context
drm: drm_pci needs dma-mapping.h
[PATCH] drm: Fix issue reported by Coverity in drivers/char/drm/via_irq.c
Fix de-reference of 'dev_priv' before NULL check.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
- #if 0 the following unused global function:
- drm_ioremap_nocache()
- make the following needlessly global functions static:
- agp_remap()
- drm_lookup_map()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix a crash when running hpacucli with multiple logical volumes on a cciss
controller. We were not properly initializing the disk->queue and causing
a fault.
Thanks to Hasso Tepper for reporting the problem. Thanks to Steve Cameron
for root causing the problem. Most of the patch just moves things around.
The fix is a one-liner.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen Cameron <steve.cameron@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Limit USB_STORAGE_ISD200 to whatever BLK_DEV_IDE and USB_STORAGE
are set to (y, m) since isd200 calls ide_fix_driveid() in the
BLK_DEV_IDE code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The at91_cf driver got out of sync with certain changes in the PCMCIA
layer, notably getting rid of some duplication of data ... causing the
version merged to kernel.org to fail compiling.
This patch gives the at91_cf platform device a new iomem resource, using
it so this new pcmcia scheme works. It also cleans up some whitepsace
bugs that have accumulated over time (mostly too-long lines).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch by Benjamin Herrenschmidt after debugging by Brian Hinz.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Brian Hinz <bphinz@hotmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (170 commits)
commit 3d9dd7564d
Author: Zach Brown <zach.brown@oracle.com>
Date: Fri Apr 14 16:04:18 2006 -0700
[PATCH] ip_output: account for fraggap when checking to add trailer_len
During other work I noticed that ip_append_data() seemed to be forgetting to
include the frag gap in its calculation of a fragment that consumes the rest of
the payload. Herbert confirmed that this was a bug that snuck in during a
previous rework.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 08d099974a
Author: Linus Walleij <triad@df.lth.se>
Date: Fri Apr 14 16:03:33 2006 -0700
[IRDA]: smsc-ircc2, smcinit support for ALi ISA bridges
...
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (679 commits)
commit 7676f83aeb
Author: James Bottomley <James.Bottomley@steeleye.com>
Date: Fri Apr 14 09:47:59 2006 -0500
[SCSI] scsi_transport_sas: don't scan a non-existent end device
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
commit 3c0c25b97c
Author: Moore, Eric <Eric.Moore@lsil.com>
Date: Thu Apr 13 16:08:17 2006 -0600
[SCSI] mptfusion - fix panic in mptsas_slave_configure
Driver panic when RAID logical volume was present when driver
loaded, or when a RAID logical volume was created on the fly.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6: (78 commits)
commit e97b81ddbb
Author: Mark M. Hoffman <mhoffman@lightlink.com>
Date: Thu Mar 23 16:50:25 2006 +0100
[PATCH] i2c-parport: Make type parameter mandatory
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (169 commits)
commit 78a596b449
Author: Adrian Bunk <bunk@stusta.de>
Date: Fri Mar 31 01:38:12 2006 -0800
[PATCH] remove kernel/power/pm.c:pm_unregister()
Since the last user is removed in -mm, we can now remove this long deprecated
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 21440d3133
Author: David Brownell <david-b@pacbell.net>
Date: Sat Apr 1 10:21:52 2006 -0800
[PATCH] dma doc updates
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (158 commits)
commit 4f705ae3e9
Author: Bjorn Helgaas <bjorn.helgaas@hp.com>
Date: Mon Apr 3 17:09:22 2006 -0700
[PATCH] DMI: move dmi_scan.c from arch/i386 to drivers/firmware/
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
...
From: Linus Walleij <triad@df.lth.se>
This patch enables support for ALi ISA bridges when we run the smcinit
code. It is needed to properly configure some Toshiba laptops.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the STIR421x case, when the firmware upload fails, we need to
unregister_netdev. Otherwise we hit a BUG on free_netdev(), if sysfs
is enabled.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Asus A6VA notebook was reported to need a PCI quirk to unhide
the SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The init function for the RPA PCI Hotplug driver returns -ENODEV in the
case that no hotplug-capable slots are detected in the system. This is
bad, since hot-capable slots can be added after boot to a purely virtual
POWER partition. This is also bad because DLPAR I/O operations depend
on the rpaphp module.
Change the rpaphp init module to return success for the case of
partitions that own no hotplug-capable slots at boot. Such slots can be
dynamically added after boot.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The naming of the constant defined for PCI ID 1022:7450 does not seem
to match the information at http://pciids.sourceforge.net/:
http://pci-ids.ucw.cz/iii/?i=1022
There 1022:7450 is listed as "AMD-8131 PCI-X Bridge" while 1022:7451
is listed as "AMD-8131 PCI-X IOAPIC". Yet, the current definition for
0x7450 is PCI_DEVICE_ID_AMD_8131_APIC. It seems to me like that name
should map to 0x7451, while a name like PCI_DEVICE_ID_AMD_8131_BRIDGE
should map to 0x7450.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Print more diagnostic info to help identify the source of power management
suspend failures.
Example:
usb_hcd_pci_suspend(): pci_set_power_state+0x0/0x1af() returns -22
pci_device_suspend(): usb_hcd_pci_suspend+0x0/0x11b() returns -22
suspend_device(): pci_device_suspend+0x0/0x34() returns -22
Work-in-progress. It needs lots more suspend_report_result() calls sprinkled
everywhere.
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The manual driver <-> device binding attribute in sysfs doesn't return
the correct value on failure or success of driver_probe_device.
driver_probe_device returns 1 on success (the driver accepted the
device) or 0 on probe failure (when the driver didn't accept the
device but no real error occured). However, the attribute can't just
return 0 or 1, it must return the number of bytes consumed from buf
or an error value. Returning 0 indicates to userspace that nothing
was written (even though the kernel has tried to do the bind/probe and
failed). Returning 1 indicates that only one character was accepted in
which case userspace will re-try the write with a partial string.
A more correct version of driver_bind would return count (to indicate
the entire string was consumed) when driver_probe_device returns 1
and -ENODEV when driver_probe_device returns 0. This patch makes that
change.
Signed-off-by: Ryan Wilson <hap9@epoch.ncsc.mil>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tries to fix an issue in drivers/base/class.c, please
review and apply if correct.
Patch Description:
"parent_class" is checked for NULL already, so removed the unnecessary
check.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as667) changes the __device_release_driver() routine to
prevent it from crashing when it runs across a device not on any bus.
This seems logical, inasmuch as the corresponding bus_add_device()
routine has an explicit check allowing it to accept such devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an init-time kernel log message.
http://marc.theaimsgroup.com/?l=linux-kernel&m=114232987208628&w=3
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the w83792d driver keep quiet when misdetecting a chip. This can
happen, and the user doesn't need to know.
Also renumber the messages, and add one, for consistency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The m41t00 i2c/rtc driver currently uses a tasklet to schedule
interrupt-level writes to the rtc. This patch causes the driver
to use a workqueue instead.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tasklet is not suitable for what the ds1374 driver does: neither sleeping
nor mutex operations are allowed in tasklets, and ds1374_set_tlet may do
both.
We can use a workqueue instead, where both sleeping and mutex operations
are allowed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents an Oops if booted with "console=ttyUSB0" but without a
USB-serial dongle, and plugged one in afterwards.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for a clone of Nokia DKU-5 cable made by
Ours Technology Inc for Nokia phones with PopPort (Nokia 3100 and others).
The cable uses PL2303 USB-to-serial converter from Prolific Technology Inc.
Signed-off-by: Tomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get the "usb-bus" clock and ensure it is enabled
when the OHCI core is in use.
It seems that a few bootloaders do not enable the
UPLL at startup, which stops the OHCI core having
a 48MHz bus clock. The improvements to the clock
framework for the s3c24xx now allow the USB PLL
to be started and stopped when being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When not using this patch, the kernel will continuously return "input irq
status -32 received", while making the keyboard unusable. This can be
easely resolved using HID_QUIRK_NOGET. Vendor-ID and Device-ID should be
applied to hid-core.c, and making an entry to make use of it.
Signed-off-by: Jeffrey Vandenbroucke <jeffrey@wirehead.be>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone recently posted a bug report where it turned out that uhci-hcd
was disagreeing with the UHCI controller over whether or not a port was
suspended: The driver thought it wasn't and the hardware thought it was.
This patch (as665) fixes the problem and simplifies the driver by
removing the internal state-tracking completely. Now the driver just
asks the hardware whether a port is suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
