This code was cribbed from niu, so gfar_set_hash_opts() begins by
converting the ethtool flow class code into a class code for Sun
Neptune hardware, then does the same thing again for the hardware it's
really dealing with. It may also return -1 (-EPERM) for some
unhandled ethtool flow class codes.
Remove the useless code and definitions, and fix the error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a stab at replacing old ethtool phys_id with set_phys_id
on the Qlogic 10Gb driver. Compile tested only.
Not sure if set_led_cfg will flash continuously, or needs
to be replaced by ETHTOOL_ID_ON/ETHTOOL_ID_OFF
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to add an ntuple data extensions to the rx network flow
classification specifiers. The idea is to allow ntuple to be displayed via
the network flow classification interface.
The first patch had some left over stuff from the original flow extension
flags I had added. That bit is removed in this patch.
The second had some left over comments that stated we ignored bits in the
masks when we actually match them.
This work is based on input from Ben Hutchings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to prevent a possible null pointer dereference if
NETIF_F_NTUPLE is defined but the set_rx_ntuple function pointer is not.
The main motivation behind this patch is to eventually replace the ntuple
interfaces entirely with the network flow classifier interfaces. This
allows the device drivers to maintain the ntuple check internally while
using the network flow classifier interface for setting up and displaying
rules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conversion.
This also enables toggling TX VLAN offload and fixes TX checksumming
race with offload changes.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes possible race when changing receive checksum state
and removes IPV6_CSUM_GEN_HACK as it's always set.
BTW, The claim about fake IPV6 checksum looks dubious. If that were true,
then there's a problem in networking core and should be fixed there and not
in random drivers.
BTW#2, there's no MAINTAINERS entry for this driver. I assume this driver
is supported by Micrel?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also removes TSO as it's made fully in software --- better to leave this
to networking core.
If the MAC features can be detected at probe time and not at open, then
stmmac_fix_features could be simplified by limiting hw_features. That's
also better for users as they don't see offloads being togglable but
never turned on.
Redundant fallbacks for TX csum are removed as it's already handled
by network core.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple conversion with a bit of needed cleanup.
This also fixes:
- confusion around vlan_features in rtl8169_vlan_mode(),
- problem with broken TSO for too big MTU (the limit is set
at 0xFFF --- max MSS field value).
SG+IP_CSUM+TSO is left disabled by default, based on suggestion by
David Dillow.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up after merge with NETIF_F_RXHASH implementation.
This allows to toggle NETIF_F_RXHASH and NETIF_F_HW_VLAN_TX.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove offload changing ethtool ops which drivers don't really support:
- fs_enet
- ucc_geth
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reverse path filter interferes with IPsec subnet-to-subnet tunnels,
especially when the link to the IPsec peer is on an interface other than
the one hosting the default route.
With dynamic routing, where the peer might be reachable through eth0
today and eth1 tomorrow, it's difficult to keep rp_filter enabled unless
fake routes to the remote subnets are configured on the interface
currently used to reach the peer.
IPsec provides a much stronger anti-spoofing policy than rp_filter, so
this patch disables the rp_filter for packets with a security path.
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sk_buff available for other use in fib_validate_source().
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some debug to the reset function to print out the
reason why it fails.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the PL-25A1 by adding the appropriate
USB ID's. This chip is used in the Belkin 'Windows Easy Transfer'
Cables.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up a couple of instances of incorrect whitespace
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cnic_stop_hw() -> cnic_cm_stop_bnx2x_hw() is called under rtnl_lock()
from NETDEV_DOWN event, it waits for cnic_delete_task() to complete.
It will deadlock when cnic_delete_task() takes rtnl_lock() before
calling cnic_ulp_stop_one().
We fix it by removing the rtnl_lock() in cnic_delete_task().
cnic_ulp_stop_one() has mutex and atomic bit ops to prevent important
operations from being done more than once, so it is not necessary to take
rtnl_lock().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Things left as they were:
- atl1: is RX checksum really enabled?
- atl2: copy-paste from atl1, with-errors-on-modify I presume
- atl1c: there's a bug: MTU can't be changed if device is not up
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup hint: Some features are calculated in tg3_get_invariants() and
the rest in its caller --- tg3_init_one(). This is not changed here.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the driver uses GRO and not LRO, LRO settings are ignored anyway
and are removed here to avoid confusion.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple conversion.
This also fixes a bug in TX checksum toggling --- driver was changing
NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
just IP_CSUM. This needs testing and so is not changed here.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling setup_wol after a reset is inconsequential.
The WOL setting should be programmed before FLR.
And yes, FLR does not erase wol information.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of a fixed sized array for vf_cfg, allocate the size dynamically
depending on number of VFs the device supports.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user supplied num_vfs value need not be compared
against a static BE_MAX_VF, but can be checked against
the actual VFs that the device can support.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer and BE can both use SLI_INTF_REG to check a VF or a PF.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rxhash support,
Based on initial work by Eric Dumazet.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1018b5c01636c7c6bda31a719bda34fc631db29a ("Set rt->rt_iif more
sanely on output routes.") breaks rt_is_{output,input}_route.
This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".
To fix it, this does:
1) Add "int rt_route_iif;" to struct rtable
2) For input routes, always set rt_route_iif to same value as rt_iif
3) For output routes, always set rt_route_iif to zero. Set rt_iif
as it is done currently.
4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c6e1a0d12ca7b4f22c58e55a16beacfb7d3d8462 broken the calc
(net: Allow no-cache copy from user on transmit)
of checksum, which may cause some tcp packets be dropped because
incorrect checksum. ssh does not work under today's net-next-2.6
tree.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ethtool infrastructure for blinking, which is now does
locking at higher level.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udev fully replaces this special file system that only contains CAPI
NCCI TTY device nodes. User space (pppdcapiplugin) works without
noticing the difference.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes error from sparse:
CHECK drivers/net/xen-netback/xenbus.c
drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield
int have_hotplug_status_watch:1;
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eq_next_idx is not getting reset to zero during suspend.
This causes resume to fail. Added the fix.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed msix_vec_idx to eq_idx in be_eq_obj struct.
Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure.
These members are used in INTX mode also.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new ethtool set physical id model. Remove no longer used
timer, and fix docbook comment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cleanup error codes to no lie about things that driver doesn't
support. If device is down report -EAGAIN (same as Broadcom), and
if port doesn't blink then error as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this case, need to add element to device private to hold
original led state.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement new ethtool set_phys_id on Chelsio cxgb3 board.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
