Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform independent header files to arch/arm/include/asm, leaving
those in asm/arch* and asm/plat* alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claim the initrd memory exclusively, and order other memory
reservations beforehand. This allows us to determine whether
the initrd memory was overwritten, and disable the initrd in
that case.
This avoids a 'bad page state' bug.
Tested-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(20072fd0c9 lost most of its changes
somehow, came from a mbox archive applied with git-am. No idea
what happened. This puts back the missing bits. --rmk)
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems this small label was lost in the last merge. Without it
no CPU type is selected for the MX2 family of processors. And a build
will fail badly...
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The shared mmap code works fine for the test case, which only checked
for two shared maps of the same file. However, three shared maps
result in one mapping remaining cached, resulting in stale data being
visible via that mapping. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Feroceon platforms that have a branch prediction unit, bit 11 of the
cp15 control register controls the BPU. This patch keeps the old value
of this bit instead of always clearing it.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds basic mach support for the mx2 processor family, based
on the original freescale code and adapted to mainline kernel coding
style.
This part adds the global build only.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
This patch adds the I-cache invalidation in update_mmu_cache if the
corresponding vma is marked as executable. It also invalidates the
I-cache if a thread migrates to a CPU it never ran on.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring
(depending on the model) one or two Feroceon CPU cores with 512K of L2
cache and VFP coprocessors running at (depending on the model) between
800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe
interfaces that can each run either in x4 or quad x1 mode, three USB
2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two
TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI
interface, four UARTs, and depending on the model, two or four gigabit
ethernet interfaces.
This patch adds basic support for the platform, and allows booting
on the MV78x00 development board, with functional UARTs, SATA, PCIe,
GigE and USB ports.
Signed-off-by: Stanislav Samsonov <samsonov@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Add support for the Feroceon 88fr571-vd CPU core as found in e.g.
the Marvell Discovery Duo family of ARM SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Add support for the Shiva 88fr131 CPU core as found in e.g. the
Marvell Kirkwood family of ARM SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the unified Feroceon L2 cache controller
as found in e.g. the Marvell Kirkwood and Marvell Discovery Duo
families of ARM SoCs.
Note that:
- Page table walks are outer uncacheable on Kirkwood and Discovery
Duo, since the ARMv5 spec provides no way to indicate outer
cacheability of page table walks (specifying it in TTBR[4:3] is
an ARMv6+ feature).
This requires adding L2 cache clean instructions to
proc-feroceon.S (dcache_clean_area(), set_pte()) as well as to
tlbflush.h ({flush,clean}_pmd_entry()). The latter case is handled
by defining a new TLB type (TLB_FEROCEON) which is almost identical
to the v4wbi one but provides a TLB_L2CLEAN_FR flag.
- The Feroceon L2 cache controller supports L2 range (i.e. 'clean L2
range by MVA' and 'invalidate L2 range by MVA') operations, and this
patch uses those range operations for all Linux outer cache
operations, as they are faster than the regular per-line operations.
L2 range operations are not interruptible on this hardware, which
avoids potential livelock issues, but can be bad for interrupt
latency, so there is a compile-time tunable (MAX_RANGE_SIZE) which
allows you to select the maximum range size to operate on at once.
(Valid range is between one cache line and one 4KiB page, and must
be a multiple of the line size.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the L1 D cache range operations that
are supported by the Marvell Discovery Duo and Marvell Kirkwood
ARM SoCs.
Signed-off-by: Stanislav Samsonov <samsonov@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU
core running at between 400 MHz and 1.0 GHz, and features a 64 bit
DDR controller, 512K of internal SRAM, two x4 PCI-Express ports,
two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs,
two TWSI controllers, and IDMA/XOR engines.
This patch adds support for the Marvell LB88RC8480 Development
Board, enabling the use of the PCIe interfaces, the ethernet
interfaces, the TWSI interfaces and the UARTs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
There are a couple more Feroceon-based SoCs out in the field that use
different Variant and Architecture fields in their Main ID registers
-- this patch tweaks the processor match/mask in proc-feroceon.S to
catch those SoCs as well.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Flushing the L1 D cache with a test/clean/invalidate loop is very
easy in software, but it is not the quickest way of doing it, as
there is a lot of overhead involved in re-scanning the cache from
the beginning every time we hit a dirty line.
This patch makes proc-feroceon.S use "clean+invalidate by set/way"
loops according to possible cache configuration of Feroceon CPUs
(either direct-mapped or 4-way set associative).
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Annotate the entries for the 88fr531-vd CPU core in
arch/arm/boot/compressed/head.S and arch/arm/mm/proc-feroceon.S
with the full name of the core.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
More cosmetic cleanup:
- Replace 8-space indents by proper tab indents.
- In structure initialisers, use a trailing comma for every member.
- Collapse "},\n{" in structure initialiers to "}, {".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
The CPU's dma_flush_range() operation needs to clean+invalidate the
given memory area if the cache is in writeback mode, or do just the
invalidate part if the cache is in writethrough mode, but the current
proc-arm{925,926,940,946} (incorrectly) do a cache clean in the
latter case. This patch fixes that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ext4 uses ZERO_PAGE(0) to zero out blocks. We need to export
different symbols in different arches for the usage of ZERO_PAGE
in modules.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Almost all implementations of pci_iomap() in the kernel, including the generic
lib/iomap.c one, copies the content of a struct resource into unsigned long's
which will break on 32 bits platforms with 64 bits resources.
This fixes all definitions of pci_iomap() to use resource_size_t. I also
"fixed" the 64bits arch for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a set of Feroceon-specific
{copy,clear}_user_page() routines that perform more optimally than
the generic implementations. This also deals with write-allocate
caches (Feroceon can run L1 D in WA mode) which otherwise prevents
Linux from booting.
[nico: optimized the code even further]
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Since the Feroceon cache replacement policy is always pseudorandom
(and the relevant control register bit is ignored), remove the
CONFIG_CPU_CACHE_ROUND_ROBIN check from proc-feroceon.S.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Since the Feroceon doesn't have a global WT override bit like
ARM926 does, remove all code relating to this mode of operation
from proc-feroceon.S.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The proc-*.S files have the _prefetch_abort pointer placed at the end
of the processor structure but the cpu-multi32.h defines it in the
second position. The patch also fixes the support for XSC3 and the
MMU-less CPUs (740, 7tdmi, 940, 946 and 9tdmi).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By default, this option was selected by the platform Kconfig. This
patch adds "depends on" to L2X0 so that it can be enabled/disabled
manually.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch enables the building of Linux for the PB1176 platform.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since 2f569af (CONFIG_HIGHPTE vs. sub-page page tables.) pte_free() calls
pte_lock_deinit() and dec_zone_page_state(). So free_pgd_slow must not call
the latter two when calling the first.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"cat /dev/mem" may cause kernel Oops for boards with PHYS_OFFSET != 0
because character device is mapped to addresses starting from zero
and there is no protection against such situation.
Patch just add this.
Signed-off-by: Alexandre Rusev <arusev@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
