The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:
- Remove struct omap_display_platform_data. It was used just as a
wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
dss hwmods do not need the platform data. This should also work better
for DT, as we can create omapdss device programmatically in generic omap
boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI driver uses dsi_get_dsidev_id() to get the ID number for the DSI
instance. However, there were a few places where dsidev->id was used
instead of the function. Fix those places to use the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To ease device tree adaptation in the future, rewrite TFP410 platform
data handling to be done inside probe(), so that probe() is the only
place where we need to handle the DT/pdata choice.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb_parse_vram_param()'s check for end pointer returned from
simple_strtoul() is wrong, causing the code to bug if the second or
later vram parameters are non-parseable, for example
"omapfb.vram=0:2M,:5M".
However, even in that case the code will most likely bail out with
-EINVAL in the following checks, so the bug is probably not a fatal one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Currently when multiple overlays are active, OMAPFB_SETUP_PLANE fails.
Instead of failing, allow it to configure the first overlay as if there
was only one overlay, the remaining ones will have to be configured in
other ways (sysfs).
This allows overlay-controlling programs (like video players) to function
properly when framebuffer is cloned to another display (like TV).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
VENC output type (composite/svideo) doesn't have to be fixed by board
wiring, it is possible to also provide composite signal through svideo
luminance connector (software enabled), which is what pandora does.
Having to recompile the kernel for users who have TV connector types
that don't match default board setting is very inconvenient, especially
for users of a consumer device, so add support for switching VENC output
type at runtime over a new sysfs file output_type.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
The functions calc_fclk_five_taps() and check_horiz_timing_omap3() use the
function dispc_mgr_get_device() to get the omap_dss_device pointer to which
the manager is connected, the width of the panel is derived from that.
The manager's timing is stored in it's private data in APPLY. This contains
the latest timings applied to the manager. Pass these timings to
dispc_ovl_setup() and use them in the above functions. Remove the function
dispc_mgr_get_device() as it isn't used any more.
Signed-off-by: Archit Taneja <archit@ti.com>
The pixel clock rate for the TV manager is calculated by checking the device
type connected to the manager, and then requesting the VENC/HDMI interface for
the pixel clock rate.
Remove the use of omap_dss_device pointer from here by checking which interface
generates the pixel clock by reading the DSS_CTRL.VENC_HDMI_SWITCH bit.
Signed-off-by: Archit Taneja <archit@ti.com>
The omap_dss_device pointer declared in dss_ovl_setup_fifo() isn't used. Remove
the pointer variable declaration and it's assignment.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI and HDMI interfaces use their 'set_timing' functions to take in a new
set of timings. If the panel is disabled, they do not disable and re-enable
the interface. Currently, the manager timings are applied in hdmi_power_on()
and dpi_set_mode() respectively, these are not called by set_timings if the
panel is disabled.
When checking overlay and manager data, the DSS driver uses the last applied
manager timings, and not the timings held by omap_dss_device struct. Hence,
there is a need to apply the new manager timings even if the panel is disabled.
Apply the manager timings if the panel is disabled. Eventually, there should be
one common place where the timings are applied independent of the state of the
panel.
Signed-off-by: Archit Taneja <archit@ti.com>
In order to check the validity of overlay and manager info, there was a need to
use the omap_dss_device struct to get the panel resolution. The manager's
private data in APPLY now contains the manager timings. Hence, we don't need to
rely on the display resolution any more.
Pass the manager's timings in private data to dss_mgr_check(). Remove the need
to pass omap_dss_device structs in the functions which check for the validity
of overlay and manager parameters.
Signed-off-by: Archit Taneja <archit@ti.com>
If a manager is disabled, there is no guarantee at any point in time that all
it's parameters are configured. There is always a chance that some more
parameters are yet to be configured by a user of DSS, or by DSS itself.
However, when the manager is enabled, we can be certain that all the parameters
have been configured, as we can't enable a manager with an incomplete
configuration. Therefore, if a manager is disabled, don't check for the validity
of it's parameters or the parameters of the overlays connected to it. Only check
once it is enabled. Add a check in dss_check_settings_low() to achieve the same.
Signed-off-by: Archit Taneja <archit@ti.com>
Create a function dss_mgr_check_timings() which wraps around the function
dispc_mgr_timings_ok(). This is mainly a clean up to hide dispc functions
from interface drivers.
dss_mgr_check_timings() is added in the function dss_mgr_check(), it currently
takes the timings maintained in the omap_dss_device struct. This would be later
replaced by the timings stored in the manager's private data.
Make dss_mgr_check_timings() and dispc_mgr_timings_ok() take a const
omap_video_timings pointer since these functions just check the timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Replace the function dispc_mgr_set_timings() with dss_mgr_set_timings() in the
interface drivers. The latter function ensures that the timing related DISPC
registers are configured according to the shadow register programming model.
Remove the call to dispc_mgr_go() in dpi_set_timings() as the manager's go bit
is set by dss_mgr_set_timings().
Signed-off-by: Archit Taneja <archit@ti.com>
DISPC manager size and DISPC manager blanking parameters(for LCD managers)
follow the shadow register programming model. Currently, they are programmed
directly by the interface drivers.
To configure manager timings using APPLY, there is a need to introduce extra
info flags for managers, similar to what is done for overlays. This is needed
because timings aren't a part of overlay_manager_info struct configured by a
user of DSS, they are configured internally by the interface or panel drivers.
Add dirty and shadow_dirty extra_info flags for managers, update these flags
at the appropriate places. Rewrite the function extra_info_update_ongoing()
slightly as checking for manager's extra_info flags can simplify the code a bit.
Create function dss_mgr_set_timings() which applies the new manager timings to
extra_info.
Signed-off-by: Archit Taneja <archit@ti.com>
Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The wrong bit field was being updated in DSS_CTRL when trying to configure the
clock source of DSI2 functional clock. Use the correct bit field based on the
dsi module number.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI core register offset macros aren't defined in ascending order of their
values, some of the offset macros are also redefined. The same issues occur when
these core registers are dumped.
Clean up the ordering of HDMI core registers and remove repeated registers in
the definition in ti_hdmi_4xxx_ip.h and in ti_hdmi_4xxx_core_dump().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function ti_hdmi_4xxx_core_dump has some bugs, the following mention the
bugs and the solutions:
- The macros DUMPCORE and DUMPCOREAV in ti_hdmi_4xxx_core_dump() use
hdmi_pll_base() for the offsets needed to calculate register addresses, use
functions hdmi_core_sys_base() amd hdmi_av_base() to calculate the correct
offsets for CORE_SYS and CORE_AV registers.
- Many of the CORE_AV registers use the DUMPCORE macro, and hence the register
addresses are calculated incorrectly. Rename the current DUMPCOREAV macro as
DUMPCOREAV2 as it takes 2 arguments to dump indexed CORE_AV registers, create
a new macro called DUMPCOREAV which is now used for dumping non-indexed
CORE_AV registers.
Thanks to Ancy Tom <ancytom@gmail.com> for pointing out the issues.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.
This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC_FCLK is incorrectly used as functional clock of DISPC in scaling
calculations. So, DISPC_CORE_CLK replaces as functional clock of DISPC.
DISPC_CORE_CLK is derived from DISPC_FCLK divided by an independent DISPC
divisor LCD.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 DISPC video overlays suffer from some undocumented horizontal position
and timing related limitations leading to SYNCLOST errors. Whenever the image
window is moved towards the right of the screen SYNCLOST errors become
frequent. Checks have been implemented to see that DISPC driver rejects
configuration exceeding above limitations.
This code was successfully tested on OMAP3. This code is written based on code
written by Ville Syrjälä <ville.syrjala@nokia.com> in Linux OMAP kernel. Ville
Syrjälä <ville.syrjala@nokia.com> had added checks for video overlay horizontal
timing and DISPC horizontal blanking length limitations.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 and OMAP4, the DISPC Scaler can downscale an image up to 4 times, and
up to 2 times in OMAP2. However, with predecimation, the image can be reduced
to 16 times by fetching only the necessary pixels in memory. Then this
predecimated image can be downscaled further by the DISPC scaler.
The pipeline is configured to use a burst of size 8 * 128 bits which consists
of 8 mini bursts of 16 bytes each. So, horizontal predecimation more than 16
can lead to complete discarding of such mini bursts. L3 interconnect may
handover the bus to some other initiator and inturn delay the fetching of
pixels leading to underflows. So, maximum predecimation limit is fixed at 16.
Based on the downscaling required, a prior calculation of predecimation values
for width and height of an image is done. Since, Predecimation reduces quality
of an image higher priorty is given to DISPC Scaler for downscaling.
This code was successfully tested on OMAP2, OMAP3 and OMAP4. Horizontal and
vertical predecimation worked fine except for some synclost errors due to
undocumented errata in OMAP3 which are fixed later and skewed images were seen
on OMAP2 and OMAP3 during horizontal predecimation which will be addressed in
the future patches.
This code is based on code written by Lajos Molnar <lajos@ti.com> who had added
predecimation support for NV12/YUV/rotated/SDMA buffers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add displays to panel-generic-dpi.c
Prime View PD050VL1 (640 x 480)
Prime View PD104SLF (800 x 600)
Prime View PM070WL4 (800 x 480)
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the DISPC manager timings related function by:
- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.
We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.
For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.
This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The EDT ET0500G0DH6 is a 5 inch display. It is
tested on an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the Mitsubishi display
AA084SB01. This is a 7 inch LVDS display. It is tested with
an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On pandora we use .set_timings to alter refresh rate,
so add .check_timings/.set_timings functions.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the size of memory region that is being set up is the same as before,
we don't have to do memory and layer busy checks.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since any power on stabilisation delay for the supply itself should be
taken care of transparently by the regulator API when the regulator is
enabled the additional delay that the TPO-TD03MTEA1 driver adds after
that returned should be due to the requirements of the device itself
rather than the supply (the delay is also suspicously long for one for
a regulator to ramp). Correct the comment to avoid misleading people
taking this code as a reference.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TAAL driver contains some regulator support which is currently unused
(the code is there but the one panel supported by the driver doesn't have
any regulators provided). This code mostly looks like an open coded
version of the regulator core bulk API.
The only additional feature is that a voltage range can be set once when
the device is opened, though this is never varied at runtime. The general
expectation is that if the device is not actively managing the voltage of
the device (eg, doing DVFS) then any configuration will be done using the
constraints rather than by drivers, saving them code and ensuring that
they work well with systems where the voltage is not configurable.
If systems are added needing regulator support this can be added back in,
though it should be based on core features rather than open coding things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some OMAP versions the TRM says that the pixel clock from DISPC can
be used as an input clock for DSI PLL, instead of the default, which is
sysclk. For some OMAP versions the bits affecting this are marked as
reserved. This feature has never been tested, so it's unknown if the HW
even works, and has never been used.
To clean things up, this patch removes the functionality. This should
not affect any board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the DSS clocks have restrictions on their frequency based on the
OPP in use. For example, maximum frequency for a clock may be 180MHz in
OPP100, but 90MHz in OPP50. This means that when a high enough pixel
clock or function clock is required, we need to use OPP100.
However, there's currently no way in the PM framework to make that kind
of request. The closest we get is to ask for very high bus throughput
from the PM framework, which should effectively force OPP100.
This patch is a simple version for handling the problem. Instead of
asking for OPP100 only when needed, this patch asks for OPP100 whenever
DSS is active. This obviously is not an optimal solution for cases with
small displays where OPP50 would work just fine. However, a proper
solution is a complex one, and this patch is a short term solution for
the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
We do the dss driver registration in a rather strange way: we have the
higher level omapdss driver, and we use that driver's probe function to
register the drivers for the rest of the dss devices.
There doesn't seem to be any reason for that, and additionally the
soon-to-be-merged patch "ARM: OMAP: omap_device: remove
omap_device_parent" will break omapdss initialization with the current
registration model.
This patch changes the registration for all drivers to happen at the
same place, in the init of the module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'next/cleanup-exynos-clock' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
(includes an update to v3.3-rc6)
Currently the shadow-dirty flags for manual update displays is cleared
in the apply_irq_handler when an update has finished. This is not
correct, as the shadow registers are taken into use (i.e. after that
they are not dirty) when the update is started.
Move the mgr_clear_shadow_dirty() call from apply_irq_handler to
dss_mgr_start_update() to fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These are no longer needed with the recent iomap.h
changes.
Reported-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
wait_pending_extra_info_updates() currently does a hacky second check
for extra_info_update_ongoing() at the end of the function to show a
warning if extra_info update is still ongoing. The call to
extra_info_update_ongoing() should really be inside spinlock, but that's
a bit heavy just for verification.
Rather than that, check the return value of the
wait_for_completion_timeout() and print an error if it has timeouted or
returned an error.
Even better would be to return the error value and act on it in the
callers of wait_pending_extra_info_updates. However, it's not clear what
the callers should do in case of an error, as the error should only
happen if there's a bug in the driver or the HW. So we'll just print the
warning for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If DSS suspends within the functions dss_mgr_wait_for_go(),
dss_mgr_wait_for_go_ovl() or dss_mgr_wait_for_vsync(). It may lose it's clock
and lead to a register access failure.
Request runtime_pm around these functions.
[archit@ti.com: Moved runtime_pm calls to wait_for_go/vsync functions rather
then calling them from omap_dispc_wait_for_irq_interruptible_timeout()]
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
coef3_M8 had an incorrect phase with 50% more intensity. This resulted in
banding on slightly down/upscaled images. Fixed a rounding error in coef5_M9.
Also removed ARRAY_LEN macro as ARRAY_SIZE is the standard linux one.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add missing but supported color formats for GFX pipeline in dss features:
RGBX16-4444, RGBA16-4444 and XRGB16-1555.
In dispc_ovl_set_color_mode():
- Remove unsupported modes on GFX pipeline: YUV2 and UYVY. Replace these by
missing modes supported by GFX pipelines: RGBX16-4444 and RGBA16-4444.
- Fix swapped modes on VID pipelines: RGBX16-4444 and XRGB16-4444.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While calculating regm and regmf value add using M2 divider in
the equation.
Formula for calculating:
Output clock on digital core domain:
CLKOUT = (M / (N+1))*CLKINP*(1/M2)
Internal oscillator output clock on internal LDO domain:
CLKDCOLDO = (M / (N+1))*CLKINP
The current code when allows variable M2 values as input
ignores using M2 divider values in calculation of regm and regmf.
so fix it by using M2 in calculation although the default value for
M2 is 1.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is only needed when using SRAM for framebuffer,
and the support for SRAM framebuffer is about to get
removed.
Otherwise we cannot move most of plat/io.h to be a local
iomap.h for mach-omap2.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb driver used platform_data to get fb memory areas and formats
defined by the board file.
This patch removes omapfb's (both old and new omapfb) use of the
memory data in platform_data, because:
- No board uses them currently
- It's not board file's job to define things like amount of default
framebuffer memory. These should come from the bootloader via command
line parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The MCLK mode defines a factor to divide the clock that is used to
generate the Audio Clock Regeneration packets, MCLK.
The divisor is not used when the CTS value is calculated by HW.
When the value is calculated by SW, it depends on the silicon
revision.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the MCLK is used to drive the Audio Clock Regeneration packets,
the initialization procedure is to set ACR_CTRL[2] to 0 and then
back again to 1. Also, devices that do not support the MCLK, use
the TMDS clock directly by leaving ACR_CTRL[2] set to 0.
The MLCK clock divisor, mclk_mode, is configured only if MLCK
is used. Such configuration is no longer related to the CTS mode
as in some silicon revisions CTS SW-mode is used along with the MCLK.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Certain OMAP4 revisions (i.e., 4430 ES2.3, 4460, and 4470) use
a pseudo clock (generated from the TMDS clock), MCLK, to drive the
generation of Audio Clock Regeneration packets. Other devices
(i.e., 4430 ES2.[0,2]) use the TMDS clock directly.
This patch adds a new DSS feature for MCLK support. It also rearranges
the omap_dss_features structures to reflect the devices supporting it.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Over time better gamma has been determined and tuned with some
equipment so update the defaults. From subjective point of view
dark shades should be better visible.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
During system suspend, at the time DSS is being suspended, SPI is
already suspended and it's clocks are cut. Because of this trying to
communicate with the LCD controller results in a deadlock.
To fix this, split out LCD programming parts of display enable/disable
functions and perform them from SPI PM callbacks instead when system is
being suspended. If the display is just being enabled/disabled, do it
from DSS callbacks as before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With AVI infoframe various parameters of video stream such as
aspect ratio, quantization range, videocode etc will be indicated
from source to sink.Thus AVI information needs to be set/accessed
by the middle ware based on the video content.
Thus this parameter is now moved to the ip_data structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Innolux AT080TN52 800x600 panel.
Tested with AM3517 based board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.
Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of dss_feat_id members has increased to a large value, the current
way of assigning a subset of these features (for a particular OMAP) as a mask
is no longer feasible.
Maintain the subset of features supported as lists. Make the function
dss_has_feature() traverse through this list.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.
This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
This patch converts the drivers in drivers/video/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ba02fa37de disabled the
venc driver registration on OMAP4. Since the driver never gets
probed/initialised your get a dereferenceed NULL pointer if you
try to get info from /sys/kernel/debug/omapdss/venc
Return info message about disabled venc if venc_dump_regs() gets called.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Due to changes in struct hdmi_config, the pixel clock has to be obtained
differently.
The pixel clock is needed to calculate the CTS value as defined in the
HDMI specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code and mode parameters are already a part of the ip_data structure
so no need to keep the same parameters again in hdmi global structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the timing match logic, Instead of the statically mapped method
to get the corresponding timings for a given code and mode, move to a
simpler array indexed method. It will help to scale up to add more
timings when needed.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the vsync polarity, hsync polarity, interlace to hdmi_video_timings.
Remove the now duplicate structure hdmi_timings.
update the static table structure in HDMI with CEA/VESA code and mode.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
video interface structure is a duplicate structure with parameters which are
already present in ip_data config structure, Thus removing the structure and
modifying corresponding code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.
This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
