->rename already gets the target inode passed if it exits. Pass it down to
xfs_rename so that we can avoid looking it up again. Also simplify locking
as the first lock section in xfs_rename can go away now: the isdir is an
invariant over the lifetime of the inode, and new_parent and the nlink
check are namespace topology protected by i_mutex in the VFS. The projid
check needs to move into the second lock section anyway to not be racy.
Also kill the now unused xfs_dir_lookup_int and remove the now-unused
first_locked argumet to xfs_lock_inodes.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30903a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The writer field is not needed for non_DEBU builds so remove it. While
we're at i also clean up the interface for is locked asserts to go through
and xfs_iget.c helper with an interface like the xfs_ilock routines to
isolated the XFS codebase from mrlock internals. That way we can kill
mrlock_t entirely once rw_semaphores grow an islocked facility. Also
remove unused flags to the ilock family of functions.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30902a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Opencode xfs-kill-xfs_dir_lookup_int here, which gets rid of a lock
roundtrip, and lots of stack space. Also kill the di_mode == 0 check that
has been done in xfs_iget for a few years now.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30901a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Similar to rmdir and remove - avoids a potential transaction reservation
overrun.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30900a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Unless XFS_IGET_CREATE is passed xfs_iget will return ENOENT if it
encounters an inode with di_mode == 0. Remove the duplicated checks in the
callers.
(the log recovery case is not touched for now)
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30898a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
It's currently used by the ACL code to read di_mode/di_uid, but these are
simple 32bit scalar values we can just read directly without locking.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30897a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
We can just check i_mode / di_mode directly.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30896a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c💯9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/scsi/aic7xxx/aic7770_osm.c:53:58: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:355:47: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:372:55: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:997:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1003:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1165:46: warning: Using plain integer as NULL pointer
drivers/scsi/fdomain.c:1446:40: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:1650:51: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:3171:42: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:5732:52: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8189:31: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8225:34: warning: Using plain integer as NULL pointer
drivers/scsi/dpt_i2o.c:156:32: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:954:42: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:1104:18: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: add named choice group
kconfig: fix choice dependency check
kconifg: 'select' considered less evil
dontdiff: ignore timeconst.h
dontdiff: add modules.order
kbuild: fix unportability in gen_initramfs_list.sh
kbuild: fix help output to show correct arch
kbuild: show defconfig subdirs in make help
kconfig: reversed borderlines in inputbox
drivers/atm/nicstar.c:418:25: warning: Using plain integer as NULL pointer
drivers/char/drm/r128_cce.c:820:25: warning: Using plain integer as NULL pointer
drivers/char/tty_io.c:1183:10: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel/cpuset.c:1268:52: warning: Using plain integer as NULL pointer
kernel/pid_namespace.c:95:24: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
init/do_mounts_rd.c:215:13: warning: Using plain integer as NULL pointer
init/do_mounts_md.c:136:45: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 18 errors and several warnings given by checkpatch.pl:
- use of C99 // comments;
- trailing whitespace;
- 'switch' and 'case' not at the same indentation level;
- no space before the open parenthesis of the 'if' and 'switch' statements;
- space between function name and open parenthesis (though I have introduced
such warnins in some places since the code looks prettier with the spaces);
- including <asm/io.h> instead of <linux/io.h>;
- line over 80 characters.
In addition to these changes, also do the following:
- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
sil_set_dma_mode() 'static const';
- change the string of the 'if' statements into the 'switch' statement in
sil_pata_udma_filter();
- drop the needless '==' operators from the 'if' statements where a condition
is a mere bit test;
- remove needless initializer for the 'tmp' variable in init_chipset_siimage();
- beautify groups of the variable initializers and assignment operators;
- add new line after variable definitions;
- remove new line between the comment and the statements it refers to;
- remove needless curly braces and parentheses;
- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h
It turns out this was done for ARM, and we can simply always select
HAVE_IDE on ARM instead of manually tracking which platforms might
possible have an IDE controller directly or indirectly.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ETRAX_IDE was marked as broken last year with the comment
"it doesn't even compile currently".
Remove it since it won't get fixed in the near future.
On Mon, Apr 14, 2008 at 02:50:19PM +0200, Mikael Starvik wrote:
> You can remove it for now and we will resubmit a new if/when we get around
> to fix it.
[bart: ported it over IDE tree]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
{ide,scc}_dma_setup().
* Remove no longer needed ->dma_prdtable field from ide_hwif_t.
While at it:
* Use ATA_DMA_TABLE_OFS define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
pdc202xx_new host driver.
* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->dma_host_set and ->dma_start methods (+ __scc_dma_end() helper)
so scc_ide_{in,out}b() can be used directly.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.
* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
'ide_drive_t *drive' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_read method so out{b,w}(), in{b,w}() and superio_ide_inb()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so scc_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so outb()/inb() and mm_outw()/mm_inw()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so cris_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use ->OUTBSYNC method for executing commands so the posting is done
if needed (this affects only pmac and scc_pata host drivers at the moment).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* proc_reports_siimage() is now only called by init_chipset_siimage()
so inline it there.
* Use array instead of switch statement for reporting clock modes.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to
merge code accessing configuration registers through PCI and MMIO together.
[ because of this SATA initialization bits from setup_mmio_siimage() are
moved to init_chipset_siimage() ]
This also cuts code size a bit:
text data bss dec hex filename
4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before
3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in setup_mmio_siimage().
* Rename 'tmpbyte' variable to 'tmp' in init_chipset_siimage().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do clocking register posting earlier in setup_mmio_siimage()
to match code in init_chipset_siimage().
This is a preparation for the next patch which merges PCI and MMIO
code paths together.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_MMIO host flag and set it for hosts which use
default_hwif_mmiops().
v2:
* Fix kernel panic in pmac host driver (',' should be '|').
Thanks to Kamalesh for reporting it + testing the fix
and to Andrew for hinting me about the source of the issue.
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument
(thanks to Stephen Rothwell for catching it).
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
