In dwc2_hsotg_udc_start(), don't initialize the controller for device
mode unless we are actually in device mode.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The struct ffs_data::private_data has a pointer to
ffs_dev stored in it during the ffs_fs_mount() function
however it is not cleared when the ffs_dev is freed
later which causes the ffs_closed function to crash
with "Unable to handle kernel NULL pointer dereference"
error when using the data in ffs_data::private_data.
This clears this pointer during the ffs_free_dev clean
up function.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch follows the similar fix in dwc2. See
commit 5268ed9d2e ("usb: dwc2: Fix dr_mode validation")
Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.
The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.
Behavior summary:
module : actual
HW config dr_mode : dr_mode
---------------------------------
host host any : host
host dev any : INVALID
host otg any : host
dev host any : INVALID
dev dev any : dev
dev otg any : dev
otg host any : host
otg dev any : dev
otg otg any : dr_mode
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulpi_register_interface() accepts a const struct ulpi_ops and dwc3
doesn't perform any changes to this struct at runtime, so there's no
reason it shouldn't be constant.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
None of the core ulpi functions perform any changes to the operations
struct, and logically as a struct that contains function pointers
there's no reason it shouldn't be constant.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Operations now use ulpi->dev.parent directly instead of via the
ulpi_ops struct, making this field unused. Remove it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the removal of the old {read|write} operations, we can now safely
rename the new api operations {read|write}_dev to use the shorter and
clearer names {read|write}, respectively.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all users use the new api callbacks, remove the old api
callbacks and force new interface drivers to use the new api.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The old read, write callbacks in struct ulpi_ops have been deprecated
in favor of new callbacks that pass the parent device directly.
Replace the used callbacks in dwc3's ulpi component with the new api.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add these two new api callbacks to struct ulpi_ops. These are different
than read, write in that they pass the parent device directly instead
of via the ops argument.
They are intended to replace the old api functions.
If the new api callbacks are missing, revert to calling the old ones
as before.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Once ulpi operations use the parent device directly, this will be
needed during the operations used in ulpi_register() itself, so set
the parent field before calling any ulpi operations.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This property is not needed because the periodic fifos are not
configurable. So it was incorrect to add this property in the first
place.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As kill_all_requests() potentially flushes TX FIFO, we should should
free FIFO after calling it. Otherwise FIFO could stay unflushed properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since FIFO is always freed in dwc2_hsotg_ep_disable(), ep->fifo_index
is always 0 in dwc2_hsotg_ep_enable(), hence code inside if() block is
never executed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we handle FIFOs and endpoint separately, using variable named 'ep'
in context of FIFO is misleading, hence we rename it to 'fifo'.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to DWC2 documentation, DPTxFSize field of DPTXFSIZn register
is read only, which means that software cannot change FIFO size.
Register description says:
"The value of this register is the Largest Device Mode Periodic Tx Data
FIFO Depth (parameter OTG_TX_DPERIO_DFIFO_DEPTH_n), as specified during
coreConsultant configuration."
That means, that we have to setup only FIFO start addresses (DPTxFStAddr),
taking into account reset values of DPTxFSize.
Initialize FIFO start addresses properly and remove unneeded core related
to incorrect FIFO size initialization.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In context of FIFO registers we use ep->fifo_index instead of ep->index.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as debug, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some UVC commands require additional data (non zero uvc->event_length).
Add usb_ep_queue() call, so uvc_function_ep0_complete() can be called
and send received data to the userspace.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch sets the quirk_avoids_skb_reserve flag to improve performance
of a network gadget driver (e.g. f_ncm.c) if USB-DMAC is used.
For example (on r8a7795 board + f_ncm.c + iperf udp mode / receiving):
- without this patch: 90.3 Mbits/sec
- with this patch: 273 Mbits/sec
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds to support no_skb_reserve function to improve
performance for some platforms. About the detail, please refer to
the commit log of "quirk_avoids_skb_reserve" in
include/linux/usb/gadget.h.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a flag "no_skb_reserve" in struct eth_dev.
So, if a peripheral driver sets the quirk_avoids_skb_reserve flag,
upper network gadget drivers (e.g. f_ncm.c) can avoid skb_reserve()
calling using the flag as well.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some platforms (e.g. USB-DMAC on R-Car SoCs) has memory alignment
restriction. If memory alignment is not match, the usb peripheral
driver decides not to use the DMA controller. Then, the performance
is not good.
In the case of u_ether.c, since it calls skb_reserve() in rx_submit(),
it is possible to cause memory alignment mismatch.
So, this patch adds a new quirk "quirk_avoids_skb_reserve" to avoid
skb_reserve() calling in u_ether.c to improve performance.
A peripheral driver will set this flag and network gadget drivers
(e.g. f_ncm.c) will reference the flag via gadget_avoids_skb_reserve().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
trivial typo fix in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for r8a7796 (R-Car M3-W).
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Memory allocated for goku_udc device is not deallocated at error
paths in goku_probe(), because gadget_release() destructor
is not registered yet.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistakes in dev_err messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's perfectly fine to have all configfs functions
built-in while having modular legacy gadgets. Let's
allow for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use gadget's framework allocation function instead of directly calling
usb_ep_alloc_request().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should always use free_ep_req() when allocating requests with
alloc_ep_req().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The default_length parameter of alloc_ep_req was not really necessary
and gadget drivers would almost always create an inline function to pass
the same value to len and default_len.
This patch removes that parameter and updates all calls to alloc_ep_req() to
use the new API.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TX settings can be calibrated for particular hardware. The
phy is reset by Linux, so this cannot be handled by the bootloader.
The TRM mentions that the maximum resistance should be used for the
DN/DP calibration in order to pass USB certification.
The values for the TX registers are poorly described in the TRM.
The meanings of the register values were taken from another
NXP-provided document:
https://community.nxp.com/message/566147#comment-566912
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver expicitly looks for "usb2-phy" or "usb3-phy", but we
never noted these names in the documentation.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add revision number constants for the 3.00a and 3.10a releases.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_CONFIG0_SETUP.
When this flag is enabled, FunctionFS userspace drivers can process
non-standard control requests in configuration 0.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It can sometimes be necessary for gadget drivers to process non-standard
control requests, which host devices can send without having sent
USB_REQ_SET_CONFIGURATION.
Therefore, the req_match() usb_function method is enhanced with the new
parameter "config0". When a USB configuration is active, this parameter
is false. When a non-core control request is processed in
composite_setup(), without an active configuration, req_match() of the
USB functions of all available configurations which implement this
function, is called with config0=true. Then the control request gets
processed by the first usb_function instance whose req_match() returns
true.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_ALL_CTRL_RECIP. When this flag is enabled, control requests,
which are not explicitly directed to an interface or endpoint, can be
handled.
This allows FunctionFS userspace drivers to process non-standard
control requests.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if the /dev/hidg* chardev is automatically created, one
has to guess which one belongs to which function. In the case
of multiple HID functions, or maybe even multiple peripherals,
this becomes difficult.
Add the dev (with major and minor number) to configfs to allow
looking up (or even creating) the right device node for each
function. This file is read-only.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This change makes sure that the ALSA buffers are cleaned if an endpoint
becomes disabled.
Before this change, if the internal ALSA buffer did overflow, the MIDI
function would stop sending MIDI to the host.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
