For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.
Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.
Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts
This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).
Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).
Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.
Add some comments regarding periodic interrupt usage.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a missing rcu_read_unlock() before jumping out
of the ieee80211_change_station() function in the
error case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sign of correction coefficients was lost in the calculations, which
caused high packetloss in 802.11a mode after the results were applied.
Fixed by removing unneccesary and broken AND with a bit mask.
Signed-off-by: Lukas Turek <8an@praha12.net>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_local.wstats is a remnant from the
days when we still had to worry about wireless
extensions in mac80211 -- it can be removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This rewrites the error handling policies in the TX status handler.
It tries to be error-tolerant as in "try hard to not crash the machine".
It won't recover from errors (that are bugs in the firmware or driver),
because that's impossible. However, it will return a more or less useful
error message and bail out. It also tries hard to use rate-limited messages
to not flood the syslog in case of a failure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been tested with a 802.11 frame generator and by checking the FCS field
of each received frame with the value reported by the Atheros hardware. This
patch is useful if you are trying to analyze non standard 802.11 frame going
over the air.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 is able to detect when it's been hard-killed, but doesn't update
the core rfkill state or update userspace. Ensure that the state is updated,
allowing the rfkill core to notify userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libipw unconditionally calls wiphy_unregister, but it's up to the driver
to register it in the first place. ipw2100 fails to do so. Add the necessary
glue code, and also ensure that rfkill statuses get set up appropriately.
(Augmented for proper wiphy_unregister placement. -- JWL)
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initiate the conversion of libipw to the new cfg80211 configuration API.
For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.
(v2: Fix unconditional wiphy_unregister in libipw which was causing
problems for ipw2100, somewhat based on prior attempted fix
by Zhu Yi <yi.zhu@intel.com>. Previously both original version of
this patch and Zhu Yi's fix attempt were reverted due to
discovery of regressions. -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is sometimes useful to debug HT issues
as it shows what exactly the stack thinks
the peer supports.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With WEXT, it happens frequently that the SME
requests an authentication but then deauthenticates
right away because some new parameters came along.
Every time this happens we print a deauth message
and send a deauth frame, but both of that is rather
confusing. Avoid it by aborting the authentication
process silently, and telling cfg80211 about that.
The patch looks larger than it really is:
__cfg80211_auth_remove() is split out from
cfg80211_send_auth_timeout(), there's no new code
except __cfg80211_auth_canceled() (a one-liner) and
the mac80211 bits (7 new lines of code).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
* transmitter, which must be equal to the sender (origin)
* receiver (on the wireless medium), which is the AP in
the case of managed mode
* the recipient (destination), which is on the APs local
network segment
In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.
To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.
Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enforce all device constraints on the descriptor memory region.
There are several constraints on the descriptor memory, as documented
in the specification. The current code does not enforce them and/or
incorrectly enforces them.
Those constraints are:
- The address limitations on 30/32bit engines, that also apply to
the skbs.
- The 4k alignment requirement on 30/32bit engines.
- The 8k alignment requirement on 64bit engines.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's enough code to have its own file, I think.
Especially since I'm going to add to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_esbq_exec’:
drivers/net/wireless/wl3501_cs.c:387: warning: ‘tmp’ is used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:384: note: ‘tmp’ was declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When going from/to a WEP protected IBSS, we need to
leave this one and join a new one to take care of
the changed capability.
Cc: Hong Zhang <henryzhang62@yahoo.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not assigning the vif pointer causes an oops.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 rejects all association requests when in associated state. This
prevents clean roaming within an ESS since one would first need to
disassociate before being able to request reassociation.
Accept the reassociation request and let the old association to be
dropped when the new one is completed. This fixes nl80211-based
roaming with the current snapshot version of wpa_supplicant (that has
code for requesting reassociation explicitly withthe previous BSSID
attribute).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.
It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.
kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: David-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes warnings:
drivers/net/wireless/wl12xx/wl1251_rx.c: In function 'wl1251_rx_status':
drivers/net/wireless/wl12xx/wl1251_rx.c:75:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to IEEE80211 standard all the data packets have to be sent with
TODS bit set. This patch fixes the null data packet format which was sent
without TODS bit set. This should fix many problems associated with
power save. Janne Ylalehto also found this fix in the same time as mine,
for a different bug he was working on.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases, the IRQ loop handler could acknowledge an interrupt to
the chipset, but not service it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Filter out unwanted events to reduce wakeups.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for IRQ looping. Helps in the case that we have e.g. multiple
packets coming from the network when we wake up from the ELP.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch increases the number of beacons to be missed before generating
SYNC TIMEOUT event. It increases the beacon timeout period to 500
microseconds, which gives enough time for the firmware to receive probe
response or beacon. Also handled the regain event from firmware once it
receives a probe response or beacon.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the dtim period obtained from the mac80211 to firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dtim period obtained from the mac80211 is not set to the firmware.
This patch implements the acx command to set correct tbtt and dtim value
to the firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ps-poll template aid bits 14 and 15 were not masked as required by the
standard. Mask them so that aid is sent in correct format.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier firmware was stored to a memory area allocated with kmalloc()
but finding a a contiguous area of memory long enough for the firmware is
very difficult in certain cases. better to allocate the memory for firmware
with vmalloc() instead and use a small buffer for DMA transfers.
Thanks to Eero Tamminen for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement (slightly) delayed entry into ELP. This will cure several
problems:
- It works around a firmware race condition if ELP is entered too fast
after commands (resulting in ELP timeout -traces)
- It will reduce the number of sleep-wake cycles between already
scheduled events such as interrupts and tx, hence improving
performance (less delay in switching between RX and TX)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable beacon filtering when PSM is enabled
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable beacon filtering with the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
