Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove needless setting of drive->using_dma from auide_dma_check().
* Split off auide_mdma_filter() from auide_dma_check().
* Use ide_tune_dma() in auide_dma_check(), this fixes following issues:
- device's DMA capability bit not being checked
- device not being checked against generic DMA blacklist
- transfer mode not being set on device/host
* Add PIO autotune fallback to auide_dma_check().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().
* ATI controllers allow separate PIO and DMA timings so remove programming
of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed
atiixp_dma_2_pio() helper.
* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
support for SWDMA modes for now.
* Enable support for MWDMA0 mode.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always set ->autotune in init_hwif_sis5513(), this means practically
no change in behavior since PIO was always tuned in ->ide_dma_check
and >autotune was always set for ->dma_base == 0 case.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add sis_ata133_get_base() helper function for obtaining the address of
the drive control registers on chipset_family == ATA_133 chipsets.
* Add three helper functions for programming PIO/MWDMA timings:
- sis_ata16_program_timings() (for ATA_16/33/66/100a chipset families)
- sis_ata100_program_timings() (for ATA_100/133a chipset families)
- sis_ata133_program_timings() (for ATA_133 chipset family)
MWDMA timings are taken from datasheets and they match ATA spec.
* Add generic helper function sis_program_timings() and use it in
->set_pio_mode and ->set_dma_mode methods (previously the driver
depended on BIOS to program the correct MWDMA timings).
* Remove redundant !chipset_family check from init_hwif_sis5513()
(init_chipset_sis5513() guarantees that we will never get here if
chipset_family cannot be determined).
* SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in
datasheets and for SWDMA0 mode timing requirements are impossible to
fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling
of SWDMA modes from sis_set_dma_mode().
* Enable DMA support for chipset_family == ATA_16.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds id strings for Corsair 1GB (identified as Hyperstone Model1)
inside legacy/ide-cs.c.
It also includes some minor whitespace cleanups.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The patch described by the following excerpt from ChangeLog-2.6.22 makes
it impossible to use UDMA on a Tyan S2707 motherboard (SvrWks CSB5):
commit 2d5eaa6dd7
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Thu May 10 00:01:08 2007 +0200
ide: rework the code for selecting the best DMA transfer mode (v3)
...
This one-line patch against 2.6.23 fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300.
[MIPS] Cache: Provide more information on cache policy on bootup.
[MIPS] Fix aliasing bug in copy_user_highpage, take 2.
[MIPS] VPE loader: convert from struct class_ device to struct device
[MIPS] MIPSsim: Fix booting from NFS root
[MIPS] Alchemy: Get rid of au1xxx_irq_map_t.
[MIPS] Alchemy: Get rid of au_ffz().
[MIPS] Alchemy: Get rid of au_ffs().
[MIPS] Alchemy: cleanup interrupt code.
[MIPS] Lasat: Fix build by conversion to irq_cpu.c.
[MIPS] Lasat: Add #ifndef ... #endif include warpper to lasatint.h.
[MIPS] IP22: Enable -Werror.
[MIPS] IP22: Fix warning.
[MIPS] IP22: Complain if requesting the front panel irq failed.
[MIPS] vmlinux.lds.S: Handle KPROBES_TEXT.
[MIPS] vmlinux.lds.S: Fix handling of .notes in final link.
[MIPS] vmlinux.lds.S: Remove duplicate comment.
[MIPS] MSP71XX: Add workarounds file.
[MIPS] IP32: Fix build by conversion to irq_cpu.c.
Extremly low values are of dubious usefulness anyway but in this case
they actually were killing Qemu which simply wasn't able to complete
mips_next_event() within 0x30 100MHz cycles even on fast hosts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should help making bug reports for the gadzillion of cores with all
their configuration and synthesis options more useful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Turns out b868868ae0 wasn't quite right.
When called for a page that isn't marked dirty it would artificially
create an alias instead of doing the obvious thing and access the page
via KSEG0.
The same issue also exists in copy_to_user_page and copy_from_user_page
which was causing the machine to die under rare circumstances for example
when running ps if the BUG_ON() assertion added by the earlier fix was
getting triggered.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSsim probably doesn't have any sort of environment, but writing
a zero in it kills even the compiled in command line. This prevents
booting via NFS root.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-berr.o
arch/mips/sgi-ip22/ip22-berr.c: In function 'ip22_be_interrupt':
arch/mips/sgi-ip22/ip22-berr.c💯 warning: passing argument 2 of 'die_if_kernel' discards qualifiers from pointer target type
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the warning:
CC arch/mips/sgi-ip22/ip22-reset.o
arch/mips/sgi-ip22/ip22-reset.c: In function 'reboot_setup':
arch/mips/sgi-ip22/ip22-reset.c:239: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (264 commits)
[ALSA] version 1.0.15
[ALSA] Fix thinko in cs4231 mce down check
[ALSA] sun-cs4231: improved waiting after MCE down
[ALSA] sun-cs4231: use cs4231-regs.h
[ALSA] This simplifies and fixes waiting loops of the mce_down()
[ALSA] This patch adds support for a wavetable chip on
[ALSA] This patch removes open_mutex from the ad1848-lib as
[ALSA] fix bootup crash in snd_gus_interrupt()
[ALSA] hda-codec - Fix SKU ID function for realtek codecs
[ALSA] Support ASUS P701 eeepc [0x1043 0x82a1] support
[ALSA] hda-codec - Add array terminator for dmic in STAC codec
[ALSA] hdsp - Fix zero division
[ALSA] usb-audio - Fix double comment
[ALSA] hda-codec - Fix STAC922x volume knob control
[ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz
[ALSA] hda-codec - Fix for Fujitsu Lifebook C1410
[ALSA] mpu-401: remove MPU401_INFO_UART_ONLY flag
[ALSA] mpu-401: do not require an ACK byte for the ENTER_UART command
[ALSA] via82xx - Add DXS quirk for Shuttle AK31v2
[ALSA] hda-codec - Fix input_mux numbers for vaio stac92xx
...
improve performance of sys_time(). sys_time() returns time in seconds,
but it does so by calling do_gettimeofday() and then returning the
tv_sec portion of the GTOD time. But the data structure "xtime", which
is updated by every timer/scheduler tick, already offers HZ granularity
time.
the patch improves the sysbench oltp macrobenchmark by 4-5% on an AMD
dual-core system:
v2.6.23:
#threads
1: transactions: 4073 (407.23 per sec.)
2: transactions: 8530 (852.81 per sec.)
3: transactions: 8321 (831.88 per sec.)
4: transactions: 8407 (840.58 per sec.)
5: transactions: 8070 (806.74 per sec.)
v2.6.23 + sys_time-speedup.patch:
1: transactions: 4281 (428.09 per sec.)
2: transactions: 8910 (890.85 per sec.)
3: transactions: 8659 (865.79 per sec.)
4: transactions: 8676 (867.34 per sec.)
5: transactions: 8532 (852.91 per sec.)
and by 4-5% on an Intel dual-core system too:
2.6.23:
1: transactions: 4560 (455.94 per sec.)
2: transactions: 10094 (1009.30 per sec.)
3: transactions: 9755 (975.36 per sec.)
4: transactions: 9859 (985.78 per sec.)
5: transactions: 9701 (969.72 per sec.)
2.6.23 + sys_time-speedup.patch:
1: transactions: 4779 (477.84 per sec.)
2: transactions: 10103 (1010.14 per sec.)
3: transactions: 10141 (1013.93 per sec.)
4: transactions: 10371 (1036.89 per sec.)
5: transactions: 10178 (1017.50 per sec.)
(the more CPUs the system has, the more speedup this patch gives for
this particular workload.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This cleans up the formatting in the vDSO linker script, mostly just the
use of whitespace. It's intended to approximate the kernel standard
conventions for indenting C, treating elements of the linker script about
like initialized variable definitions.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A slight oversight tripped lockdep debugging code, each lockdep
class should have but a single init site.
Rearange the code to make this true.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Previese patch to NCR5380 broke scsi_mac because
AUTOSENSE was defined after the inclusion of
NCR5380.h. Fix it
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc64:
net/sunrpc/xprtrdma/verbs.c:1264: warning: long long unsigned int format, u64 arg (arg 3)
net/sunrpc/xprtrdma/verbs.c:1264: warning: long long unsigned int format, u64 arg (arg 4)
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a test in tgafb_mono_imageblit() for a colour image with a fall-back
to cfb_imageblit(). The test is not necessary as the only caller, which is
tgafb_imageblit(), checks it too and only invokes this function for monochrome
images. It looks like a left-over from before some changes to
tgafb_imageblit().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pixel mask calculation in tgafb_mono_imageblit() uses a variable
left-shift on a 32-bit data type by up to 32. Shifting by the width of a data
type or more produces an unpredictable result according to the C standard.
Rather than widening the data type this fix makes sure the count is between 0
and 31. The reason is not to penalise 32-bit platforms with operation on a
"long long" type for a marginal case that is meant not to happen (blitting an
image of a zero width).
The reason it has escaped for so long is the Alpha, being purely 64-bit, :-)
does not mask the shift out to 32 bits. This is a valid implementation --
producing the correct result certainly falls within "unpredictable behaviour".
It does trigger on MIPS though and it is the recent merge of the TC support
which only enabled the driver for use on anything other than the Alpha. For
MIPS when the width is 32 the mask ends up being 0 rather than 0xffffffff as
it should be and the frame buffer is not updated.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported in Bugzilla Bug 9093, upon switching to X, a small rectangular
cursor can still be seen blinking in the upper left part of the screen. It is
fbcon's text cursor. This is caused by a strange ioctl(..., KDSETMODE,
KD_TEXT) call done by something in userspace, perhaps by X itself, while the
tty is still in graphics mode. And when the tty is in KD_TEXT mode, the
cursor timer is restarted.
Although this is a userspace problem, we can work around it by delaying the
restart of the cursor timer until an fbcon_switch() is called. In other
words, the cursor timer will not be restarted even if a KD_TEXT mode switch is
requested.
Regression potential: Present but low
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This correct case, when source and destination X coordinates difference is n
multiple of pixels in byte. This is probably rare case, but this case should
supported for completeness.
Reorganization of FB_READL and FB_WRITEL calls results in code size decrease
for normal build without swapping support and size with support enabled is
reasonable too.
[adaplas]
Add missing fb_rev_pixels_in_long() prototype.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
