The spi core already checks for a slave setting mode bits that we
didn't list as supported when the master was registered. There is no
need to do it again in the master driver.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Despite many warnings in the SPI documentation and code, the spi-mxs
driver sets shared chip registers in the ->setup method. This method can
be called when transfers are in progress on other slaves controlled by the
master. Setting registers or any other shared state will corrupt those
transfers.
So fix mxs_spi_setup() to not call mxs_spi_setup_transfer().
mxs_spi_setup_transfer() is already called for each transfer when they
are actually performed in mxs_spi_transfer_one(), so the call in
mxs_spi_setup() isn't necessary to setup anything.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ssp struct has a clock rate field, to provide the actual value, in Hz,
of the SSP output clock (the rate of SSP_SCK) after mxs_ssp_set_clk_rate()
is called. It is set by mxs_ssp_set_clk_rate(), for SSP using drivers (like
SPI and MMC) to *read* if they want to know the actual clock rate. The SPI
driver isn't supposed to *write* to it.
For some reason the spi-mxs driver decides to write to this field on init,
and sets it to the value of the SSP input clock (clk_sspN, from the MXS
clocking block) in kHz. It shouldn't be setting the value, and certainly
shouldn't be setting it with the wrong clock in the wrong units.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Because the driver sets the SPI_MASTER_HALF_DUPLEX flag, the spi core
will check transfers to insure they are not full duplex. It's not
necessary to check that in the spi-mxs driver as well.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In DMA mode the chip select control bits would be ORed into the CTRL0
register without first clearing the bits. This means that after
addressing slave 1, the CTRL0 bit to address slave 1 would be still be
set when addressing slave 0, resulting in slave 1 continuing to be
addressed.
The message handling function would pass the CS value to the txrx
function, which would re-program the bits on each transfer in the
message. The selected CS does not change during a message so this is
inefficient. It also means there are two different sets of code for
selecting the CS, one for PIO that worked and one for DMA that didn't.
Change the code to set the CS bits in the message handling function
once. Now the DMA and PIO txrx functions don't need to care about CS
at all.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are two bits which control the CS line in the CTRL0 register:
LOCK_CS and IGNORE_CRC. The latter would be better named DEASSERT_CS
in SPI mode.
Setting DEASSERT_CS causes CS to be de-asserted at the end of the transfer.
It should normally be set only for the final segment of the final transfer.
The DMA code explicitly sets it in this case, but because it never clears
the bit from the ctrl0 register, it will remain set for all transfers in
subsequent messages. This results in a CS pulse between transfers.
There is a similar problem with the read mode bit never being cleared
in DMA mode.
This patch fixes DEASSERT_CS and READ being left on in DMA mode.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are three flag arguments to the PIO and DMA txrx functions. Two
are passed as pointers to integers, even though they are input only
and not modified, which makes no sense to do. The third is passed as
an integer.
The compiler must use an argument register or stack variable for each
flag this way. Using bitflags in a single flag argument is more
efficient and produces smaller code, since all the flags can fit in a
single register. And all the flag arguments get cumbersome,
especially when more are added for things like GPIO chipselects.
The "first" flag is never used, so can just be deleted.
The "last" flag is renamed to DEASSERT_CS, since that's really what it
does. The spi_transfer cs_change flag means that CS might be
de-asserted on a transfer which is not last and not de-assert on the
last transfer, so it is not which transfer is the last we need to know
but rather the transfers after which CS should be de-asserted.
This also extends the driver to not ignore cs_change when setting the
DEASSERT_CS nee "last" flag.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
INGORE_CRC, better named DEASSERT_CS, should be cleared on all tranfers
except the last. So instead of only clearing it on the first transfer, we
can just always clear it. It will set on the last transfer.
This removes the only use of the "first" flag in the transfer functions, so
that flag can be then be removed.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
These functions consist of nothing but one single writel call and are
only called once. And the names really aren't accurate or clear,
since they don't enable or disble SPI. Rather they set the bit that
controls the state of CS at the end of transfer. It easier to follow
the code to just set this bit with a writel() along with all the other
bits being set in the same function.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are two bits which control the CS line in the CTRL0 register:
LOCK_CS and IGNORE_CRC. The latter would be better named DEASSERT_CS
in SPI mode.
LOCK_CS keeps CS asserted though the entire transfer. This should
always be set. The DMA code will always set it, explicitly on the
first segment of the first transfer, and then implicitly on all the
rest by never clearing the bit from the value read from the ctrl0
register.
The PIO code will explicitly set it for the first transfer, leave it
set for intermediate transfers, and then clear it for the final
transfer. It should not clear it.
The only reason to not set LOCK_CS would be to attempt an altered
protocol where CS pulses between each word. Though don't get your
hopes up if you want to do this, as the hardware doesn't appear to do
this in any sane manner. It appears to be related to the hardware
FIFO fill level.
The code can be simplified by just setting LOCK_CS once and then not
needing to deal with it at all in the PIO and DMA transfer functions.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A small batch of fixes this week, mostly OMAP related. Nothing stands out
as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms, including
the Chromebooks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HpMx
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes this week, mostly OMAP related. Nothing stands
out as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
including the Chromebooks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <olof@lixom.net>
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=yVzH
-----END PGP SIGNATURE-----
Merge tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull parisc fixes from Helge Deller:
"This patchset includes a bugfix to prevent a kernel crash when memory
in page zero is accessed by the kernel itself, e.g. via
probe_kernel_read().
Furthermore we now export flush_cache_page() which is needed
(indirectly) by the lustre filesystem. The other patches remove
unused functions and optimizes the page fault handler to only evaluate
variables if needed, which again protects against possible kernel
crashes"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
Pull slave-dmaengine fixes from Vinod Koul:
"Another week, time to send another fixes request taking time out of
extended weekend for the festivities in this part of the world.
We have two fixes from Sergei for rcar driver and one fixing memory
leak of edma driver by Geyslan"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: edma.c: remove edma_desc leakage
rcar-hpbdma: add parameter to set_slave() method
rcar-hpbdma: remove shdma_free_irq() calls
The attached change defers the initialization of the variables tsk, mm
and flags until they are needed. As a result, the code won't crash if a
kernel probe is done with a corrupt context and the code will be better
optimized.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel. The
problem is, that in print_worker_info() we try to read the workqueue info via
the probe_kernel_read() functions which use pagefault_disable() to avoid
crashes like this:
probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq));
probe_kernel_read(&wq, &pwq->wq, sizeof(wq));
probe_kernel_read(name, wq->name, sizeof(name) - 1);
The problem here is, that the first probe_kernel_read(&pwq) might return zero
in pwq and as such the following probe_kernel_reads() try to access contents of
the page zero which is read protected and generate a kernel segfault.
With this patch we fix the interruption handler to call parisc_terminate()
directly only if pagefault_disable() was not called (in which case
preempt_count()==0). Otherwise we hand over to the pagefault handler which
will try to look up the faulting address in the fixup tables.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 9a46ad6d6d "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Olga reported that file descriptors opened with O_PATH do not work with
fstatfs(), found during further development of ksh93's thread support.
There is no reason to not allow O_PATH file descriptors here (fstatfs is
very much a path operation), so use "fdget_raw()". See commit
55815f7014 ("vfs: make O_PATH file descriptors usable for 'fstat()'")
for a very similar issue reported for fstat() by the same team.
Reported-and-tested-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull btrfs fixes from Chris Mason:
"We've got more bug fixes in my for-linus branch:
One of these fixes another corner of the compression oops from last
time. Miao nailed down some problems with concurrent snapshot
deletion and drive balancing.
I kept out one of his patches for more testing, but these are all
stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix oops caused by the space balance and dead roots
Btrfs: insert orphan roots into fs radix tree
Btrfs: limit delalloc pages outside of find_delalloc_range
Btrfs: use right root when checking for hash collision
All stable fixes except for a trivial headset mic fixup:
the removal of bogus frame checks in snd-usb-usx2y driver that have
regressed in the recent kernel versions, the HD-audio HDMI channel
map fix, and a few HD-audio device-specific fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=huaz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All stable fixes except for a trivial headset mic fixup: the removal
of bogus frame checks in snd-usb-usx2y driver that have regressed in
the recent kernel versions, the HD-audio HDMI channel map fix, and a
few HD-audio device-specific fixes"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
ALSA: hda - Add a headset mic model for ALC269 and friends
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
ALSA: hda - Add fixup for ASUS N56VZ
ALSA: hda - hdmi: Fix channel map switch not taking effect
ALSA: hda - Fix mono speakers and headset mic on Dell Vostro 5470
ALSA: snd-usb-usx2y: remove bogus frame checks
Pull i2c fixes from Wolfram Sang:
"We had various reports of problems with deferred probing in the I2C
subsystem, so this pull requst is a little bigger than usual.
Most issues should be addressed now so devices will be found
correctly. A few ususal driver bugfixes are in here, too"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-mux-pinctrl: use deferred probe when adapter not found
i2c: i2c-arb-gpio-challenge: use deferred probe when adapter not found
i2c: i2c-mux-gpio: use deferred probing
i2c: i2c-mux-gpio: don't ignore of_get_named_gpio errors
i2c: omap: Clear ARDY bit twice
i2c: Not all adapters have a parent
i2c: i2c-stu300: replace platform_driver_probe to support deferred probing
i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
i2c: i2c-imx: replace platform_driver_probe to support deferred probing
i2c: i2c-designware-platdrv: replace platform_driver_probe to support deferred probing
If we take the 2nd retry path in ext4_expand_extra_isize_ea, we
potentionally return from the function without having freed these
allocations. If we don't do the return, we over-write the previous
allocation pointers, so we leak either way.
Spotted with Coverity.
[ Fixed by tytso to set is and bs to NULL after freeing these
pointers, in case in the retry loop we later end up triggering an
error causing a jump to cleanup, at which point we could have a double
free bug. -- Ted ]
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Cc: stable@vger.kernel.org
Pull gcc "asm goto" miscompilation workaround from Ingo Molnar:
"This is the fix for the GCC miscompilation discussed in the following
lkml thread:
[x86] BUG: unable to handle kernel paging request at 00740060
The bug in GCC has been fixed by Jakub and the fix will be part of the
GCC 4.8.2 release expected to be released next week - so the quirk's
version test checks for <= 4.8.1.
The quirk is only added to compiler-gcc4.h and not to the higher level
compiler.h because all asm goto uses are behind a feature check"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Pull x86 fixes from Ingo Molnar:
"A build fix and a reboot quirk"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Add reboot quirk for Dell Latitude E5410
x86, build, pci: Fix PCI_MSI build on !SMP
ARCompact TRAP_S insn used for breakpoints, commits before exception is
taken (updating architectural PC). So ptregs->ret contains next-PC and
not the breakpoint PC itself. This is different from other restartable
exceptions such as TLB Miss where ptregs->ret has exact faulting PC.
gdb needs to know exact-PC hence ARC ptrace GETREGSET provides for
@stop_pc which returns ptregs->ret vs. EFA depending on the
situation.
However, writing stop_pc (SETREGSET request), which updates ptregs->ret
doesn't makes sense stop_pc doesn't always correspond to that reg as
described above.
This was not an issue so far since user_regs->ret / user_regs->stop_pc
had same value and both writing to ptregs->ret was OK, needless, but NOT
broken, hence not observed.
With gdb "jump", they diverge, and user_regs->ret updating ptregs is
overwritten immediately with stop_pc, which this patch fixes.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull MIPS fix from Ralf Baechle:
"Just one fix. The stack protector was loading the value of the canary
instead of its address"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: stack protector: Fix per-task canary switch
Pull drm fixes from Dave Airlie:
"All over the map..
- nouveau:
disable MSI, needs more work, will try again next merge window
- radeon:
audio + uvd regression fixes, dpm fixes, reset fixes
- i915:
the dpms fix might fix your haswell
And one pain in the ass revert, so we have VGA arbitration that when
implemented 4-5 years ago really hoped that GPUs could remove
themselves from arbitration completely once they had a kernel driver.
It seems Intel hw designers decided that was too nice a facility to
allow us to have so they removed it when they went on-die (so since
Ironlake at least). Now Alex Williamson added support for VGA
arbitration for newer GPUs however this now exposes itself to
userspace as requireing arbitration of GPU VGA regions and the X
server gets involved and disables things that it can't handle when VGA
access is possibly required around every operation.
So in order to not break userspace we just reverted things back to the
old known broken status so maybe we can try and design out way out.
Ville also had a patch to use stop machine for the two times Intel
needs to access VGA space, that might be acceptable with some rework,
but for now myself and Daniel agreed to just go back"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (23 commits)
Revert "i915: Update VGA arbiter support for newer devices"
Revert "drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done"
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Revert "drm/fb-helper: don't sleep for screen unblank when an oops is in progress"
drm/gma500: fix things after get/put page helpers
drm/nouveau/mc: disable msi support by default, it's busted in tons of places
drm/i915: Only apply DPMS to the encoder if enabled
...
Using the headset mic model will cause the headset mic to be labeled
"headset mic" instead of just "mic".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1227093
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fengguang Wu, Oleg Nesterov and Peter Zijlstra tracked down
a kernel crash to a GCC bug: GCC miscompiles certain 'asm goto'
constructs, as outlined here:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
Implement a workaround suggested by Jakub Jelinek.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Suggested-by: Jakub Jelinek <jakub@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 81b5c7bc8d.
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6e1b4fdad5.
This is part of a revert due to a userspace breakage, better explained in the revert of 1a1a4cbf4906a13c0c377f708df5d94168e7b582.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Regression fixes for audio and UVD, several hang fixes,
some DPM fixes.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 4981c4dc19 (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba7
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c1c63a14f4 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba7 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When doing space balance and subvolume destroy at the same time, we met
the following oops:
kernel BUG at fs/btrfs/relocation.c:2247!
RIP: 0010: [<ffffffffa04cec16>] prepare_to_merge+0x154/0x1f0 [btrfs]
Call Trace:
[<ffffffffa04b5ab7>] relocate_block_group+0x466/0x4e6 [btrfs]
[<ffffffffa04b5c7a>] btrfs_relocate_block_group+0x143/0x275 [btrfs]
[<ffffffffa0495c56>] btrfs_relocate_chunk.isra.27+0x5c/0x5a2 [btrfs]
[<ffffffffa0459871>] ? btrfs_item_key_to_cpu+0x15/0x31 [btrfs]
[<ffffffffa048b46a>] ? btrfs_get_token_64+0x7e/0xcd [btrfs]
[<ffffffffa04a3467>] ? btrfs_tree_read_unlock_blocking+0xb2/0xb7 [btrfs]
[<ffffffffa049907d>] btrfs_balance+0x9c7/0xb6f [btrfs]
[<ffffffffa049ef84>] btrfs_ioctl_balance+0x234/0x2ac [btrfs]
[<ffffffffa04a1e8e>] btrfs_ioctl+0xd87/0x1ef9 [btrfs]
[<ffffffff81122f53>] ? path_openat+0x234/0x4db
[<ffffffff813c3b78>] ? __do_page_fault+0x31d/0x391
[<ffffffff810f8ab6>] ? vma_link+0x74/0x94
[<ffffffff811250f5>] vfs_ioctl+0x1d/0x39
[<ffffffff811258c8>] do_vfs_ioctl+0x32d/0x3e2
[<ffffffff811259d4>] SyS_ioctl+0x57/0x83
[<ffffffff813c3bfa>] ? do_page_fault+0xe/0x10
[<ffffffff813c73c2>] system_call_fastpath+0x16/0x1b
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
