GPMC CS was not freed in omap2_onenand_remove() preventing the module
from reloading after removal.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and
the real page size differs from mtd_info.writesize.
Signed-off-by: Mika Korhonen <mika.j.korhonen@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nowadays MTD devices have to be "get" before they can be
used. This has to be done with 'get_mtd_device()'. The
'blktrans_open()' function did not do this and instead
used 'try_module_get()'. Fix this.
Since 'get_mtd_device()' already gets the module, extra
'try_module_get()' is not needed.
This fixes oops when one tries to use mtdblock on top of
gluebi.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes a bug when converting dev to mtd_info by using the
drvdata of the dev, the previous code used
container_of(dev, struct mtd_info, dev), but won't work for the mtdXro
devices as they created without being contained inside mtd_info structure.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://neil.brown.name/md:
md: Use revalidate_disk to effect changes in size of device.
md: allow raid5_quiesce to work properly when reshape is happening.
md/raid5: set reshape_position correctly when reshape starts.
md: Handle growth of v1.x metadata correctly.
md: avoid array overflow with bad v1.x metadata
md: when a level change reduces the number of devices, remove the excess.
md: Push down data integrity code to personalities.
md/raid6: release spare page at ->stop()
In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
The ->quiesce method is not supposed to stop resync/recovery/reshape,
just normal IO.
But in raid5 we don't have a way to know which stripes are being
used for normal IO and which for resync etc, so we need to wait for
all stripes to be idle to be sure that all writes have completed.
However reshape keeps at least some stripe busy for an extended period
of time, so a call to raid5_quiesce can block for several seconds
needlessly.
So arrange for reshape etc to pause briefly while raid5_quiesce is
trying to quiesce the array so that the active_stripes count can
drop to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
As the internal reshape_progress counter is the main driver
for reshape, the fact that reshape_position sometimes starts with the
wrong value has minimal effect. It is visible in sysfs and that
is all.
Signed-off-by: NeilBrown <neilb@suse.de>
The v1.x metadata does not have a fixed size and can grow
when devices are added.
If it grows enough to require an extra sector of storage,
we need to update the 'sb_size' to match.
Without this, md can write out an incomplete superblock with a
bad checksum, which will be rejected when trying to re-assemble
the array.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
We trust the 'desc_nr' field in v1.x metadata enough to use it
as an index in an array. This isn't really safe.
So range-check the value first.
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is changed from RAID6 to RAID5, fewer drives are
needed. So any device that is made superfluous by the level
conversion must be marked as not-active.
For the RAID6->RAID5 conversion, this will be a drive which only
has 'Q' blocks on it.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.
md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity. The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().
The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.
For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
eeepc-laptop: fix hot-unplug on resume
ACPI: Ingore the memory block with zero block size in course of memory hotplug
ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver
ACPI: bind workqueues to CPU 0 to avoid SMI corruption
ACPI: root-only read protection on /sys/firmware/acpi/tables/*
thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM
thinkpad-acpi: restrict procfs count value to sane upper limit
thinkpad-acpi: remove dock and bay subdrivers
thinkpad-acpi: disable broken bay and dock subdrivers
hp-wmi: check that an input device exists in resume handler
Revert "ACPICA: Remove obsolete acpi_os_validate_address interface"
This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".
So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.
And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded
pr = pci_find_parent_resource(dev, r);
if (!pr || request_resource(pr, r) < 0) {
to using
if (pci_claim_resource(dev, idx) < 0) {
that "insert_resource()" now suddenly became a problem, and causes a
regression covered by
http://bugzilla.kernel.org/show_bug.cgi?id=13891
which this fixes.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.
This is a regression to 2.6.30 introduced by commit 8c90e11e35
mISDN: Use kernel_{send,recv}msg instead of open coding
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
VLB support has been broken since at least 2004-2005 period as some
changes introduced back then assumed that ->pci_dev is always valid,
lets try to fix it:
- remove duplicated SET_NETDEV_DEV() call
- call SET_NETDEV_DEV() only for PCI devices
- check for ->pci_dev validity in pcnet32_open()
[ Alternatively we may consider removing VLB support but there would not
be much gain in it since an extra driver code needed for VLB support is
minimal and quite simple. ]
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the debug printk() into the proper place and remove superfluous
NULL pointer check in pcnet32_probe1().
This takes care of the following entry from Dan's list:
drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
In the last iteration i is PHY_MAX_ADDR. the condition
`!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may
evaluate to false, which leads to a dereference of this invalid
phy_map in the phy_connect() below.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call unregister_pernet_gen_device() can exhaust memory
if module is loaded/unloaded many times.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the corner cases where the sum of MTU of the free
channels (adjusted for fragmentation overheads) is less than the MTU
of PPP link. There are at least 3 situations where this case might
arise:
- some of the channels are busy
- the multilink session is running in a degraded state (i.e. with less
than its full complement of active channels)
- by design, where multilink protocol is being used to artificially
increase the effective link MTU of a single link.
Without this patch, at most 1 fragment is ever sent per free channel
for a given PPP frame and any remaining part of the PPP frame that
does not fit into those fragments is silently discarded.
This patch restores the original behaviour which was broken by commit
9c705260fe 'ppp:ppp_mp_explode()
redesign'. Once all 'free' channels have been given a fragment, an
additional fragment is queued to each available channel in turn, as many
times as necessary, until the entire PPP frame has been consumed.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
OOPS on resume when the wireless adaptor is disabled during suspend was
introduced by "eeepc-laptop: read rfkill soft-blocked state on resume".
Unable to handle kernel NULL pointer dereference
Process s2disk
Tainted: G W
IP: klist_put
Call trace:
? klist_del
? device_del
? device_unregister
? pci_stop_dev
? pci_stop_bus
? pci_remove_device
? eeepc_rfkill_hotplug [eeepc_laptop]
? eeepc_hotk_resume [eeepc_laptop]
? acpi_device_resume
? device_resume
? hibernation_snapshot
It appears the PCI device is removed twice. The eeepc_rfkill_hotplug()
call from the resume handler is racing against the call from the ACPI
notifier callback. The ACPI notification is triggered by the resume
handler when it refreshes the value of CM_ASL_WLAN.
The fix is to serialize hotplug calls using a workqueue.
http://bugzilla.kernel.org/show_bug.cgi?id=13825
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the memory block size is zero, ignore it and don't do the memory hotplug
flowchart. Otherwise it will complain the following warning message:
>System RAM resource 0 - ffffffffffffffff cannot be added
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Don't treat the generic error as ACPI error code. Otherwise when the generic
code is returned, it will complain the following warning messag:
>ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE,
Cannot get acpi bus device [20080609]
>ACPI: Cannot find driver data
> ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609]
> Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1
Call Trace:
[<ffffffff8020da29>] show_trace_log_lvl+0x41/0x58
[<ffffffff8049a3da>] dump_stack+0x69/0x6f
.....
At the same time when the generic error code is returned, the ACPI_EXCEPTION
is replaced by the printk.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, a software-initiated SMI causes corruption unless the
SMI runs on CPU 0. An SMI can be initiated by any AML, but typically it's
done in GPE-related methods that are run via workqueues, so we can avoid
the known corruption cases by binding the workqueues to CPU 0.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=13751https://bugs.launchpad.net/bugs/157171https://bugs.launchpad.net/bugs/157691
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix those warnings:
drivers/parisc/hppb.c: In function 'hppb_probe':
drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Helge Deller <deller@gmx.de>
Fix those compiler warnings, which indeed point to a bug:
drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type
drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used
Signed-off-by: Helge Deller <deller@gmx.de>
fix the following 'make includecheck' warning:
drivers/parisc/ccio-dma.c: linux/proc_fs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
loff_t is a signed type. If userspace passes a negative ppos, the "count"
range check is weakened. "count"s bigger than HPEE_MAX_LENGTH will pass the check.
Also, if ppos is negative, the readb(eisa_eeprom_addr + *ppos) will poke in random
memory.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
This patche fixes a spelling error that has resulted from copy and pasting.
The location of the error was found using a semantic patch but the semantic
patch was not trying to find these errors. After looking things over it
seemed logical that this change was needed.
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Helge Deller <deller@gmx.de>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
HBRV-based default selection of backlight control strategy didn't work
well, at least the X41 defines it but doesn't use it and I don't think
it will stop there.
Switch to a white/blacklist. All models that have HBRV defined have
been included in the list, and initially all ATI GPUs will get
ECNVRAM, and the Intel GPUs will get UCMS_STEP.
Symptoms of incorrect backlight mode selection are:
1. Non-working backlight control through sysfs;
2. Backlight gets reset to the lowest level at every shutdown, reboot
and when thinkpad-acpi gets unloaded;
This fixes a regression in 2.6.30, bugzilla #13826
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
The standard ACPI dock driver can handle the hotplug bays and docks of
the ThinkPads just fine (including batteries) as of 2.6.27, and the
code in thinkpad-acpi for the dock and bay subdrivers is currently
broken anyway...
Userspace needs some love to support the two-stage ejection nicely,
but it is simple enough to do through udev rules (you don't even need
HAL) so this wouldn't justify fixing the dock and bay subdrivers,
either.
That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well
as support for the weird dock of the model 570, but since such support
has never left the "experimental" stage, it is also not a strong
enough reason to find a way to fix this code.
Users of ThinkPads with warm-swap bays are urged to request that _EJ3
support be added to the regular ACPI dock driver, if such feature is
indeed useful for them.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, the ThinkPad-ACPI bay and dock drivers are completely
broken, and cause a NULL pointer derreference in kernel mode (and,
therefore, an OOPS) when they try to issue events (i.e. on dock,
undock, bay ejection, etc).
OTOH, the standard ACPI dock driver can handle the hotplug bays and
docks of the ThinkPads just fine (including batteries) as of 2.6.27.
In fact, it does a much better job of it than thinkpad-acpi ever did.
It is just not worth the hassle to find a way to fix this crap without
breaking the (deprecated) thinkpad-acpi dock/bay ABI. This is old,
deprecated code that sees little testing or use.
As a quick fix suitable for -stable backports, mark the thinkpad-acpi
bay and dock subdrivers as BROKEN in Kconfig. The dead code will be
removed by a later patch.
This fixes bugzilla #13669, and should be applied to 2.6.27 and later.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Joerg Platte <jplatte@naasa.net>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
io context: fix ref counting
block: make the end_io functions be non-GPL exports
block: fix improper kobject release in blk_integrity_unregister
block: always assign default lock to queues
mg_disk: Add missing ready status check on mg_write()
mg_disk: fix issue with data integrity on error in mg_write()
mg_disk: fix reading invalid status when use polling driver
mg_disk: remove prohibited sleep operation
the code allready uses flush_kernel_dcache_page(). This patch updates the
driver to the recent sg API changes which require that either SG_MITER_TO_SG
or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page()
in sg_mitter_stop()
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
so the page will be flushed on unmap on ARCH which need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Add missing call to safe_put_page from stop() by unifying open coded
raid5_conf_t de-allocation under free_conf().
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When a user disables interrupt throttling with ethtool on 82599 devices,
the interrupt timer may not be re-enabled if hardware RSC is running. The
RSC completions in hardware don't complete before the next ITR event tries
to fire, so the ITR timer never gets re-armed. This patch increases the
amount of time between interrupts when throttling is disabled (rx-usecs =
0) when the hardware RSC deature is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A second set of feature flag bits was added, and the hardware RSC engine
flags were moved there. However, the code itself didn't make the move
completely to use the new bitmap.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our ndo_poll_controller callback is broken for anything but non-multiqueue
setups. This fixes that issue.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
* git://git.infradead.org/users/cbou/battery-2.6.31:
Add ds2782 battery gas gauge driver
olpc_battery: Ensure that the TRICKLE bit is checked
olpc_battery: Fix up eeprom read function
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/86xx: Update GE Fanuc sbc310 default configuration
powerpc/86xx: Update defconfig for GE Fanuc's PPC9A
cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c
powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards
powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards
powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards
powerpc/mm: Fix SMP issue with MMU context handling code
Rename the structure to avoid the following warning:
WARNING: vmlinux.o(.data+0x11ef4): Section mismatch in reference from the variable
s3c6400_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s3c6400_serial_drv references
the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
During kernel build process, the following warning was found:
WARNING: drivers/serial/built-in.o(.data+0x304): Section mismatch in reference from
the variable s3c2440_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s3c2440_serial_drv references the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the variable with
__exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
The same warning happened for s3c241x platform. We rename variables to avoid
these warnings. These changes also apply to s3c2400 & s3c24a0 for consistency.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Parameter order for using mk_ic_value(count, time) was reversed,
the patch fixes this.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket is hashed in last slot of pppoe hash table (PPPOE_HASH_SIZE-1)
we report it many times (up to filling seq buffer)
(Only the last socket of last slot)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems may not support input events, or registering the input
handler may have failed. So check that an input device exists before
trying to set the docking and tablet mode state during resume.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13865
Reported-and-tested-by: Cédric Godin <cedric@belbone.be>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
start_code is 69 words, but the code always writes a multiple of 16 words,
so the last 11 words written are outside the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if dev_alloc_skb() fails on the first iteration, a write to
cp->rx_ring[-1] occurs.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing to GFP_ATOMIC because the only caller in cnic/bnx2i may
be calling this function while holding spin_lock.
This problem was discovered by Mike Christie.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector,
it incorrectly shows sdvo dvi as connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-resolved against previous commit and fixed up commit message]
Signed-off-by: Eric Anholt <eric@anholt.net>
Some USB devices crash when we send them an inquiry with the EVPD bit
set, regardless of page requested (i.e. including page 0).
We only need the extended inquiry to gain access to VPD pages 0xB0 and
0xB1. These appeared in SBC2 and SBC3 respectively, so we can restrict
sending the extended inquiry to devices reporting SPC3 or higher.
This fixes bugzilla.kernel.org #13657.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[jejb: added comment]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hotplug of phys which form wide ports simply does not work at the moment. Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the fc_exch_rrq is called with fc_exch's ex_lock held.
The fc_exch_rrq allocates new exch and that requires taking
ex_lock again after EM lock. This locking order causes warning,
see more details on this warning at :-
http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html
This patch fixes this by dropping the ex_lock before calling
fc_exch_rrq().
The fc_exch_rrq needs to grab ex_lock lock again to schedule
RRQ retry and in the meanwhile fc_exch_reset could occur before
ex_lock is grabbed inside fc_exch_rrq. So to handle this case,
this patch adds additional check to detect fc_exch_reset after
ex_lock acquired and in case the fc_exch_reset occurred then
abandons the RRQ retry and releases the exch.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed unnecessary hiwat code to free up the number available IOCBs.
Eliminates unnecessary eh_ escalations due to inability to obtain IOCB
pkt for marker.
v2.
- Remove define not used anymore and fix req_q_coun accounting.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: ported patch from qlogic.com driver to upstream]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
eh_device_reset may be called from scsi error handler or sg_reset, etc.
When called from sg_reset, there will not be an associated srb. The
driver should lookup the corresponding device handle given information
from the supplied cmd structure and should not assume that there exists
an srb.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed driver bug where adapter recovery did not complete if there were
outstanding commands detected on that host adapter.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recently dm-multipath began calling blk_abort_queue. This causes all the
commands/request running on the path to have the timeout function called.
If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually
get this error and begin to call the cmd timeout handler. qla4xxx currently
does not set a timed out handler and so the default one could return
BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all
paths on the host when only one path is affected.
For software and offload iscsi we have a timed out handler already.
This patch adds a driver specific one to qla4xxx because there
are some ddb->state and session->state and command completion races
that are better handled in the LLD.
This also handles the problem where if the session is down,
we do not need the scsi eh to run until the transport code
has tried to reconnect us.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications. Sense data
in the first 32 bytes has always been correct.
Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.
Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.
Changed version number to 5.01.00-k9
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The session lock can be held in the scsi eh thread or the completion
paths run from the net softirq. This disables bhs in iscsi_eh_abort when
taking the session lock.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The trace record for SCSI abort requests has a field for the request
id of the request to be aborted. Put the real request id instead of
zero.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Under certain conditions it is possible that a WKA port ist not opened
within the expected timeframe of half a second. In this situation
the WKA port remains in the state OPENING preventing any succeding
request to open the port. This led to unrecoverable remote ports.
Fixing this by always setting an appropriate WKA port status before
leaving the function and removing the timeout value here since it's
not needed here because the general timeout processing would deal
with it if required.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In a LOWMEM condition an ERP notification would have been sent twice
causing an unpredictable behaviour of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When calling fc_remote_port_add make sure to not call it again before
fc_remote_port_delete has been called. In other words, ensure to
create a new fc_rport, then delete it, then create a new one again.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Depending on interruptions on some storage systems, the complete
channel can stall which looks like an outbound queue stall to Linux.
When trying to acquire a free SBAL for a non-SCSI command, zfcp waits
for 5 seconds for a free slot to appear. This is the right place to
detect a queue stall: If the wait times out, we assume a stalled queue
and try to recover this.
The overall strategy should be to trigger the erp from specific
events, and not try an overall escalation from one failed port to a
full-blown queue recovery. If we manage to send a command, the status
codes for this command or a timeout will trigger the right follow-on
actions.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If an action fails, retry it until the erp count exceeds the
threshold. If there is something fundamentally wrong, the FSF layer
will trigger a more appropriate action depending on the FSF status
codes.
The followup for successful actions is a different followup than
retrying failed actions, so split the code two functions to make this
clear.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After closing the port, we want it to be "not open" to consider the
action to be successful.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ELS ADISC and the GID_PN requests sent from zfcp fit into
unchained FSF requests. Change the FSF allocation logic to use
unchained requests whenever possible where everything fits in one
SBAL. This avoids acquiring more SBALs than necessary, especially
during zfcp recovery when things might be stalled.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is
ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling
ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the
nameserver did not return the d_id.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of
-EIO.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
req_q_util is not atomic, so the qdio_stat_lock must be held when
reading this variable.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We should not modify the port status after triggering an ERP action
for the port. It is not guaranteed which status is finally active
when the ERP action is performed. This can lead to situations which
are unwanted and hard to debug in case of a failure.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I've been doing this for years, and akpm picked me up on it about 12
months ago. lguest partly serves as example code, so let's do it Right.
Also, remove two unused fields in struct vblk_info in the example launcher.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Every so often, after code shuffles, I need to go through and unbitrot
the Lguest Journey (see drivers/lguest/README). Since we now use RCU in
a simple form in one place I took the opportunity to expand that explanation.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
I don't really notice it (except to begrudge the extra vertical
space), but Ingo does. And he pointed out that one excuse of lguest
is as a teaching tool, it should set a good example.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
This refactors find_vqs, making it more readable and robust, and fixing
two regressions from 2.6.30:
- double free_irq causing BUG_ON on device removal
- probe failure when vq can't be assigned to msi-x vector
(reported on old host kernels)
Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This makes delete vq the reverse of find vq.
This is required to make it possible to retry find_vqs
after a failure, otherwise the list gets corrupted.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Make vp_free_vectors do the reverse of vq_request_vectors.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
"new" was freed and then dereferenced. Also the return value wasn't being
used so I modified the caller as well.
Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git).
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is another alloc_bootmem() -> kzalloc() change, this time to
fix the non-fatal badness caused when booting with a cpm2_uart console.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'i2c-fixes-rc4' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: OMAP3430 Silicon Errata 1.153
i2c-omap: In case of a NACK|ARDY|AL return from the ISR
i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT register
i2c-sh_mobile: change module_init() to subsys_initcall()
i2c: strncpy does not null terminate string
i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC value
When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to
NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in
atmel_serial_probe makes the compile fail. This fixes the issue by only
accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 8dfd0374be ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:
...
mmc0: Minimum clock frequency too high for identification mode
mmc0: Minimum clock frequency too high for identification mode
...
The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.
But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.
This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit d6580a9f15 ("kexec: sysrq: simplify
sysrq-c handler") changed the behavior of sysrq-c to unconditional
dereference of NULL pointer. So in cases with CONFIG_KEXEC, where
crash_kexec() was directly called from sysrq-c before, now it can be said
that a step of "real oops" was inserted before starting kdump.
However, in contrast to oops via SysRq-c from keyboard which results in
panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will
not become panic unless panic_on_oops=1. It means that even if dump is
properly configured to be taken on panic, the sysrq-c from proc interface
might not start crashdump while the sysrq-c from keyboard can start
crashdump. This confuses traditional users of kdump, i.e. people who
expect sysrq-c to do common behavior in both of the keyboard and proc
interface.
This patch brings the keyboard and proc interface behavior of sysrq-c in
line, by forcing panic_on_oops=1 before oops in sysrq-c handler.
And some updates in documentation are included, to clarify that there is
no longer dependency with CONFIG_KEXEC, and that now the system can just
crash by sysrq-c if no dump mechanism is configured.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Brayan Arraes <brayan@yack.com.br>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under certain circumstances msleep(1) within the loop, which waits for the
EEPROM to be finished, might take longer than the timeout. On the next
loop the status register might now return to be ready and therefore the
loop finishes. The following check now tests if a timeout occurred and if
so returns an error although the device reported it was ready.
This fix replaces testing the occurrence of the timeout by testing the
"not ready" bit in the status register.
Signed-off-by: Sebastian Heutling <heutling@who-ing.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-cmos has two drivers, one PNP and one platform. When PNP has not
succeeded probing, platform is registered. However, it tries to
unregister both drivers unconditionally, instead of only unregistering
those that were successfully registered. This causes runtime warnings to
be emitted from the driver core code.
Fix this with a boolean variable for each driver indicating whether
registering was successful.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When data is read through DMA, the last element must be read separately
through the RX register. It cannot be transferred by the DMA. For
further details see e.g. OMAP35x TRM (table 19-16).
Without the fix the driver causes extra clocks to be clocked to the bus
after DMA RX operations. This can cause interesting behaviour with some
devices.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
[aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mcspi wake-ups are not enabled. This might cause cases where
OMAP is not waking up on mcspi events.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed off-by-one bug in loop indexes - some elements beyond windows' array
were accessed, which might result in memory access violations when
removing/suspending the device.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel X38 MCHBAR is a 64bits register, base from 0x48, so its higher base
is 0x4C.
Signed-off-by: Lu Zhihe <tombowfly@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@kernel.org> [2.6.30.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.
Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.
Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes
http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.
On Interrupt: I2C_STAT[RDR],
read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Baed on Eric's idea in order to handle multiple sdvo encoders
we implement another approach to dynamically chose real one
encoder after detection, which is contrasted with patch -
drm/i915:Construct all possible sdvo outputs for sdvo encoder.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to get best possible quality image we chose 640x480 for
NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p
TV format respectively.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I had one report of flicker due to FIFO underruns on 845G. Scott was
kind enough to test a few patches and report success with this one.
Looks like 845G measures FIFO size slightly differently than other
chips, and we were also clobbering the FIFO burst length. Fixing both
of those issues gives him a healthy machine again.
Note that we still only adjust plane A's watermark in the 830/845
case. If someone is willing to test we could support a bigger variety
of dual-head 830/845 configurations with a bit more code.
Fixes fdo bug #19304 (again).
Reported-by: Scott Hansen <scottandchrystie@comcast.net>
Tested-by: Scott Hansen <scottandchrystie@comcast.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Check FORCE_DETECT bit to be clear for the finish
of hotplug detect process. Also check possible mono
monitor which should also be marked as connected.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.
Currently no panel fitting support for eDP and backlight control
would be added in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should use current channel 'status' bits to clear DP aux channel's
done and error bits, instead of using the channel setting bits, that
will set send/busy bit again to initiate new transaction.
This also includes also some minor cleanup.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
During pipe DPMS off, instead of busy waiting pipe off, insert
delays during wait and don't loop after enough tries which matches
spec requirement. Also try to match DPMS on path by disable FDI TX
PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger
the update.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does VGA disable like DDX driver. SR01 bit 5 should be set
before VGA plane disable through control register, otherwise we
might get random crash and lockups.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now the DVO timing in LVDS data entry is obtained by using the
following step:
a. get the entry size for every LVDS panel data
b. Get the LVDS fp entry for the preferred panel type
c. get the DVO timing by using entry->dvo_timing
In our driver the entry->dvo_timing is related with the size of
lvds_fp_timing. For example: the size is 46.
But it seems that the size of lvds_fp_timing varies on the differnt
platform. In such case we will get the incorrect DVO timing entry
because of the incorrect DVO offset in LVDS panel data entry.
This also removes a hack on new IGDNG to get proper DVO timing.
Calculate the DVO timing offset in LVDS data entry to get the DVO timing
a. get the DVO timing offset in the LVDS fp data entry by using the
pointer definition in LVDS data ptr
b. get the LVDS data entry
c. get the DVO timing by adding the DVO timing offset to data entry
https://bugs.freedesktop.org/show_bug.cgi?id=22787
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: accept late unlocking of HPA
libata: Updates and fixes for pata_at91 driver
ata_piix: Add new short cable ID
ata_piix: Add new laptop short cable IDs
ahci: add device IDs for Ibex Peak ahci controllers
libata: remove superfluous NULL pointer checks
libata: add missing NULL pointer check to ata_eh_reset()
pata_pcmcia: add CNF-CDROM-ID
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: documentation: make it clear that sysfs is optional
driver core: sysdev: do not send KOBJ_ADD uevent if kobject_init_and_add fails
Dynamic debug: fix typo: -/->
driver core: firmware_class:fix memory leak of page pointers array
sysfs: fix hardlink count on device_move
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: udlfb: Add vmalloc.h include
staging: remove aten2011 driver
Staging: android: lowmemorykiller.c: fix it for "oom: move oom_adj value from task_struct to mm_struct"
Staging: serqt_usb2: fix memory leak in error case
Staging: serqt_usb2: add missing calls to tty_kref_put()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (34 commits)
USB: xhci: Stall handling bug fixes.
USB: xhci: Support for 64-byte contexts
USB: xhci: Always align output device contexts to 64 bytes.
USB: xhci: Scratchpad buffer allocation
USB: Fix parsing of SuperSpeed Endpoint Companion descriptor.
USB: xhci: Fail gracefully if there's no SS ep companion descriptor.
USB: xhci: Handle babble errors on transfers.
USB: xhci: Setup HW retries correctly.
USB: xhci: Check if the host controller died in IRQ handler.
USB: xhci: Don't oops if the host doesn't halt.
USB: xhci: Make debugging more verbose.
USB: xhci: Correct Event Handler Busy flag usage.
USB: xhci: Handle short control packets correctly.
USB: xhci: Represent 64-bit addresses with one u64.
USB: xhci: Use GFP_ATOMIC while holding spinlocks.
USB: xhci: Deal with stalled endpoints.
USB: xhci: Set TD size in transfer TRB.
USB: xhci: fix less- and greater than confusion
USB: usbtest: no need for USB_DEVICEFS
USB: musb: fix CONFIGDATA register read issue
...
We really don't want to mark the pty as a low-latency device, because as
Alan points out, the ->write method can be called from an IRQ (ppp?),
and that means we can't use ->low_latency=1 as we take mutexes in the
low_latency case.
So rather than using low_latency to force the written data to be pushed
to the ldisc handling at 'write()' time, just make the reader side (or
the poll function) do the flush when it checks whether there is data to
be had.
This also fixes the problem with lost data in an emacs compile buffer
(bugzilla 13815), and we can thus revert the low_latency pty hack
(commit 3a54297478: "pty: quickfix for the
pty ENXIO timing problems").
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ Modified to do the tty_flush_to_ldisc() inside input_available_p() so
that it triggers for both read and poll() - Linus]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes regression (battery "vanishing" on resume) introduced by
commit d0c71fe7eb ("ACPI Suspend: Enable
ACPI during resume if SCI_EN is not set") and also the issue with
the "screaming" IRQ 9.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13745
Reported-and-tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Several arrays were read before checking whether the index was within
bounds. ARRAY_SIZE() should be used to determine the size of arrays.
rates->rates has an arraysize of 1, so calling get_common_rates()
with a rates_size of MAX_RATES (14) was causing reads out of bounds.
tmp_size can increment at most to (ARRAY_SIZE(lbs_bg_rates) - 1) *
(*rates_size - 1), so that should be the number of elements of tmp[].
A goto can be eliminated: ret was already set upon its declaration.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reads bss->rates[j] before checking bounds of index, and should use
ARRAY_SIZE to determine the size of the array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The incorrect size caused benchmark results to be inflated by a factor of 4.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If enabled, during initialization BO GTT->VRAM and VRAM->GTT GPU copies are
tested across the whole GTT aperture.
This has helped uncover the benchmark copy size bug and verify the maximum
aperture size supported by the AGP bridge in my PowerBook.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Blocking here isn't something the X server mouse appreciates,
avoid the block and let userspace retry the waits.
libdrm_radeon userspace library is also expecting EBUSY not ERESTART
Signed-off-by: Dave Airlie <airlied@redhat.com>
Temporarily maps highmem pages while flushing to get a valid virtual
address to flush.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For x86 this affected highmem pages only, since they were always kmapped
cache-coherent, and this is fixed using kmap_atomic_prot().
For other architectures that may not modify the linear kernel map we
resort to vmap() for now, since kmap_atomic_prot() generally uses the
linear kernel map for lowmem pages. This of course comes with a
performance impact and should be optimized when possible.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The code was potentially dereferencig a NULL sync object pointer.
At the same time a sync object reference was potentially leaked.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the
aperture used to calculate the MC_FB_LOCATION needs to be worked
out from the CONFIG_APER_SIZE register, and not the actual vram size.
TTM VRAM size was also being initialised wrong, use actual vram size
to initialise it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we were basically always setting the GTT and VRAM flags regardless of
what userspace requested.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise if there's no GTT space we would fail the eviction, leading to
cascaded failure.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is done later in radeon_object_list_unvalidate(). Doing it twice triggers
a BUG in TTM, rendering X on KMS unusable until reboot.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix bandwidth computation and crtc priority in memory controller
so that crtc memory request are fullfill in time to avoid display
artifact.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Please consider the following updates and fixes for pata_at91 driver.
* Removed extra headers
Here we need only static memory controller properties, which are
contained in generic header at91sam9_smc.h.
No need to include any specific headers for at91sam9260 SoC.
* No harsh BUG_ON for get_clk in set_smc_timing function
get_clk is now performed in driver probing function,
probing fails if master clock is not available
* Fixed uint/ulong mess in calc_mck_cycles function
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OriginalAuthor: Michael Frey <michael.frey@canonical.com>
Signed-off-by: Steve Conklin <sconklin@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add device IDS for Ibex Peak SATA AHCI Controllers
Signed-off-by: Jaroslav Kysela <jkysela@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
host->ports[] always contain pointers to valid port structures since
a "dummy port" structure is used in case if there is no physical port.
This patch takes care of two entries from Dan's list:
drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap'
drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap'
and of another needless NULL pointer check in pata_octeon_cf.c.
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave'
Please note that this is _not_ a real bug at the moment since ata_eh_context
structure is embedded into ata_list structure and the code alwas checks for
'slave' before accessing 'sehc'.
Anyway lets add missing check and always have a valid 'sehc' pointer (which
makes code easier to understand and prevents introducing some possible bugs
in the future).
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct the xHCI code to handle stalls on USB endpoints. We need to move
the endpoint ring's dequeue pointer past the stalled transfer, or the HW
will try to restart the transfer the next time the doorbell is rung.
Don't attempt to clear a halt on an endpoint if we haven't seen a stalled
transfer for it. The USB core will attempt to clear a halt on all
endpoints when it selects a new configuration.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for controllers that use 64-byte contexts. The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot. To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure the xHCI output device context is 64-byte aligned. Previous
code was using the same structure for both the output device context and
the input control context. Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned. Define a new structure to use for the output device context and
clean up the debugging for these two structures.
The copy of the device context in the input control context does *not*
need to be 64-byte aligned.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocates and initializes the scratchpad buffer array (XHCI 4.20). This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation. The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2. The DMA address of this array is written into
slot 0 of the DCBAA.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.
However, the previous code would miss the last endpoint in a configuration
with no descriptors after it. Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code. It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pass back a babble error when this error code is seen in the transfer event TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver. The xHC will return an error code when the error count
transitions from 1 to 0. Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.
We want isochronous transfers to only be tried once, so set the error count to
one.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add more debugging to the irq handler, slot context initialization, ring
operations, URB cancellation, and MMIO writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear. Fix the interrupt service routine to clear that bit after the
event handler has run.
xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble. The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events. The first event will be for the data stage
TD with a completion code for a short packet. The second event will be for the
status stage with a successful completion code. Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD. Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.
Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address. Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes. The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.
Previous xHCI code represented 64-bit addresses with two u32 values. This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits. Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held. Those functions will allocate memory, and
take a gfp_t memory flags argument. We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition. The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.
The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings. However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.
Don't queue a reset endpoint command for root hubs. khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB). This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB). Set this field in bulk TRBs
and data stage TRBs for control transfers.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this change the loops won't start
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured. Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.
Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.
Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG.
Make sure any reference to it is also under the same #ifdef.
Without this fix, the driver failes to compile when USB_OTG is defined
but USB_MUSB_OTG isn't.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: Javier Martin <jmartinj@iname.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've opened up the case, and the chips in the ATEN UC2324 are:
Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)
(logo with AF kerned together) 0748
24BC02
SINGLP
(unknown 8-pin chip)
(logo looks like 3 or Z in circle)
ZT3243LEEA 0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)
So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver. I expect you will remove the
aten2011.c driver from the staging area.
From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board. This value
should be added to the device id table of mos7840.c.
Here's a patch that adds these devices to the driver.
From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.
These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: can't setup
orion-ehci orion-ehci.0: USB bus 1 deregistered
orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
orion-ehci: probe of orion-ehci.0 failed with error -110
which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: Ville Sundberg <vsundber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP: OHCI: hc_driver's stop method should call ohci_stop
Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
Reported-by: vikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.
Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Signed-off-by: Giacomo Lozito <james@develia.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for compilation without CONFIG_PM.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit f092c24049 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:
drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'
So I removed it.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.
This is a regression to 2.6.30 introduced by commit
8c90e11e35 ("mISDN: Use
kernel_{send,recv}msg instead of open coding")
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Required for vmalloc_32 and vfree declarations on non-x86 platforms.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is not needed, as the existing mos7840 driver works
properly for this device.
Thanks to Russell Lang for doing the work to figure this out.
Cc: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm about to merge "oom: move oom_adj value from task_struct to
mm_struct", and this fixup is needed to repair linux-next's
drivers/staging/android/lowmemorykiller.c.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a standard memory leak, as later allocations may fail even if prior
allocations did not. Then the prior allocations must be undone.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty_port_tty_get() was called without a corresponding tty_kref_put()
in qt_read_bulk_callback() and qt_close().
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If kobject_init_and_add fails, sysdev_register should not send KOBJ_ADD
uevent to userspace.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The page pointers array is allocated in fw_realloc_buffer() called by
firmware_data_write(), and should be freed in release function of firmware
device.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).
I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
When last sector is written, ready bit of status register should be
checked.
Signed-off-by: unsik Kim <donari75@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We cannot acknowledge the sector write before checking its status
(which is done on the next loop iteration) and we also need to do
the final status register check after writing the last sector.
Fix mg_write() to match mg_write_intr() in this regard.
While at it:
- add mg_read_one() and mg_write_one() helpers
- always use MG_SECTOR_SIZE and remove MG_STORAGE_BUFFER_SIZE
[bart: thanks to Tejun for porting the patch over recent block changes]
Cc: unsik Kim <donari75@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
===================================================================
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When using polling driver, little delay is required to access
status register. Without this, host might read invalid status.
Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mflash's polling driver operate in standard request_fn_proc's context,
sleep in this isn't permitted.
Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This fixes
- locking bug that was hidden by ecc2e05e73
- Regression #13821
- Spurious warning when closing and blocking for data write out
With these changes my PL2303 always ends up as ttyUSB0 when it should and
the module refcounts stay correct.
I'll do a more wholesale split & tidy of _open in the next release or two
as we get a standard tty_port_open and port->ops->init port->ops->shutdown
call backs.
Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the
reports but it passes local testing with the same hardware as Alan Stern.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also makes close stall in the normal case which is apparently
needed to fix emacs
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
net: irda: init spinlock after memcpy
ixgbe: fix for 82599 errata marking UDP checksum errors
r8169: WakeOnLan fix for the 8168
netxen: reset ring consumer during cleanup
net/bridge: use kobject_put to release kobject in br_add_if error path
smc91x.h: add config for Nomadik evaluation kit
NET: ROSE: Don't use static buffer.
eepro: Read buffer overflow
tokenring: Read buffer overflow
at1700: Read buffer overflow
fealnx: Write outside array bounds
ixgbe: remove unnecessary call to device_init_wakeup
ixgbe: Don't priority tag control frames in DCB mode
ixgbe: Enable FCoE offload when DCB is enabled for 82599
net: Rework mdio-ofgpio driver to use of_mdio infrastructure
register at91_ether using platform_driver_probe
skge: Enable WoL by default if supported
net: KS8851 needs to depend on MII
be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
...
The port lock is used to protect the port state. However the port structure
is freed on a hangup, then the lock taken on a close. The right fix is to
drop the port on tty->shutdown() but we can't yet do that due to sleep v
non-sleeping rules. Instead do the next best thing and fix it up when we are
not in -rc season.
Reported-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tid is bounded (above) by the size of default_tid_to_tx_fifo (17 elements), but
the size of priv->stations[].tid[] is MAX_TID_COUNT (9) elements.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect limits leads to reads outside array bounds.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSID_rid has space for only 3 ssids.
txPowerLevels[i] is read before the bounds check for i
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwm_wdev_alloc() returns an ERR_PTR on failure and not null. It also
prints its own dev_err() message so I removed that as well.
Compile tested only. Sorry.
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).
We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I had a problem on 4965 hardware (well, probably other hardware too,
but others don't survive my stress testing right now, unfortunately)
where the driver was sending invalid commands to the device, but no
such thing could be seen from the driver's point of view. I could
reproduce this fairly easily by sending multiple TCP streams with
iperf on different TIDs, though sometimes a single iperf stream was
sufficient. It even happened with a single core, but I have forced
preemption turned on.
The culprit was a queue overrun, where we advanced the queue's write
pointer over the read pointer. After careful analysis I've come to
the conclusion that the cause is a race condition between iwlwifi
and mac80211.
mac80211, of course, checks whether the queue is stopped, before
transmitting a frame. This effectively looks like this:
lock(queues)
if (stopped(queue)) {
unlock(queues)
return busy;
}
unlock(queues)
... <-- this place will be important
there is some more code here
drv_tx(frame)
The driver, on the other hand, can stop and start queues, which does
lock(queues)
mark_running/stopped(queue)
unlock(queues)
[if marked running: wake up tasklet to send pending frames]
Now, however, once the driver starts the queue, mac80211 can see that
and end up at the marked place above, at which point for some reason the
driver seems to stop the queue again (I don't understand that) and then
we end up transmitting while the queue is actually full.
Now, this shouldn't actually matter much, but for some reason I've seen
it happen multiple times in a row and the queue actually overflows, at
which point the queue bites itself in the tail and things go completely
wrong.
This patch fixes this by just dropping the packet should this have
happened, and making the lock in iwlwifi cover everything so iwlwifi
can't race against itself (dropping the lock there might make it more
likely, but it did seem to happen without that too).
Since we can't hold the lock across drv_tx() above, I see no way to fix
this in mac80211, but I also don't understand why I haven't seen this
before -- maybe I just never stress tested it this badly.
With this patch, the device has survived many minutes of simultanously
sending two iperf streams on different TIDs with combined throughput
of about 60 Mbps.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (34 commits)
V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro
V4L/DVB (12302): cx23885-417: fix broken IOCTL handling
V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner
V4L/DVB (12291): b2c2: fix frontends compiled into kernel
V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers
V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header).
V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges.
V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register.
V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app
V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors.
V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1)
V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e
V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used
V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support
V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881)
V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB
V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant)
V4L/DVB (12245): em28xx: add support for mt9m001 webcams
V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format
V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: fix scheduling of hrtimer ap_poll_timer
[S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on
[S390] vdso: fix per cpu area allocation
[S390] hibernation: fix register corruption on machine checks
[S390] hibernation: fix lowcore handling
When a net device goes down or when the bnx2i driver is unloaded,
the code was not generating the ISCSI_KEVENT_IF_DOWN message
properly and this could cause the userspace driver to crash.
This is fixed by sending the message properly in the shutdown path.
cnic_uio_stop() is also added to send the message when bnx2i is
unregistering.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More stuff for http://bugzilla.kernel.org/show_bug.cgi?id=9512
Some 8168 are unable to WoL when receiving is not enabled (plain
old 8169 do not seem to care).
It is not exactly pretty to leave the receiver enabled but we
should now enable DMA late enough for it to be safe. Some late
stage boot failure due to pxe and friends may benefit from the
delayed enabling of bus-mastering as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jaromír Cápík <tavvva@volny.cz>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Reset consumer of status rings to 0 when cleaning
up sw resources. Status rings are not deleted
during suspend since they have napi objects.
This ensures correct rx processing across suspen-resume.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
io[i] is read before the bounds check on i, order should be reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
io[i] is read before the bounds check on i, order should be reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
loop bound looks to be wrong, for an array of length 8
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_idx is checked to be < 4, but np->phys[] is 2 elements long
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fall back onto thinking everything's OK if either of the sequence
numbers we are asked to compare is zero, which is what was used
before sequence numbers were introduced.
[ Artem: modified the patch to be applicable to upstream UBI, added
big comment ]
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If we fail in 'ubi_eba_init_scan()', we free
'ubi->volumes[i]->eba_tbl' in there, but also later free it
in 'free_internal_volumes()'. Fix this by assigning NULL
to 'ubi->volumes[i]->eba_tbl' after it is freed.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When enabling debug with v4l_debug set to 2 or greater, the driver
OOPS's on startup. Checks dev pointer before dereferencing, in
order to prevent this OOPS.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IOCTLS will never get handled if we dont connect
video_ioctl2 to mpeg_fops.ioctl
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can
check whether it really is a tda9840, but the tuner can't. So the tvaudio
module must be loaded before the tuner module. This was also the case for
2.6.29, but the order was swapped in 2.6.30.
Thanks to Krzysztof Grygiencz for reporting and testing this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent patch didn't take into account that frontends can be compiled into
the kernel. Or that frontends compiled as modules can't be used by the
b2c2 driver if it is not a module itself.
Some frontends require multiple drivers, e.g. a demod driver and a tuner
driver. The code for the frontend support was getting added if the demod
driver was available. Change this to also require any needed tuner or SEC
drivers as well.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not just pure cosmetic, since the order affects the out-of-tree
module build at the -hg development tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request demodulator auto-detect transmission parameters in case of
garbage parameters provided by application for compatibility.
That's needed at least for MPlayer compatibility currently.
Thanks to Jelle de Jong for reporting issue and providing SSH access to
Devin for debugging.
Thanks to Devin Heitmueller for hard debug work he did to find that bug.
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced when adding the light frequency control
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the change was introduced in the zl10353 for the i2c gate behavior, this
broke the HVR-900 which was not behind a gate. Use a version of the zl10353
config profile that indicates the tuner is not behind such a gate.
Without this patch the first tune succeeds, but subsequent tuning attempts
will fail.
The change also renames the terratec zl10353 profile I wrote to be more
generic, since it is shared by the non-terratec device.
Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test
with.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly. Add the missing profile.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO. As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.
This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy walls pointed out that we were passing 0x5d to the TUNER_GO register,
instead of 0x01. Set the register properly (note the code did still work with
the incorrect value, so this does not address a regression).
Thanks to Andy Walls for noticing the issue.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add
support for the MT352 variant.
Thanks to Jelle de Jong for providing a unit to test/debug with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since frames per second is a function of cristal frequency, and this is
device-specific, add a function that allows adjusting it, via
subdev->core->s_config callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is possible to adjust the fps rate by changing some register values.
This is function of the connected Xtal at the camera sensor, being a 27
MHz cristal needed, in order to support 640x480 at 30 fps.
For now, it will only calculate the values for fps. Later patches may
introduce V4L2 ioctls, to allow frequency rate adjustments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the previous approach, autodetection were working only for the two
generic entries (em275x and em2820 unknown ones). So, if someone would
try to force probing an specific device, the code would not properly run
the autodetection code.
With the new approach, the sensor autodetection will be run not only for
the two generic entries, but also do webcam specific ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams in general don't have eeprom. So, the sensor hint code should be
called to properly detect what sensor is inside.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By having the webcam devices marked as such, it will help the em28xx
driver to do the right thing on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A couple of erroneous register writes snuck in that made the image go haywire. Remove these.
Many thanks to Grégory Lardière for finding this out
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Every time a request is enqueued or there is some work outstanding
from the ap_tasklet, the ap_poll_timer is scheduled again.
Unfortunately it was permanently called. It looked as if it was
started in the past and thus imediately expired.
This has been changed. First it is checked if the hrtimer is already
expired. Then the expiring time is forwarded and the timer restarted.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Incorrect device area lengths are being passed to device_area_is_valid().
The regression appeared in 2.6.31-rc1 through commit
754c5fc7eb.
With the dm-stripe target, the size of the target (ti->len) was used
instead of the stripe_width (ti->len/#stripes). An example of a
consequent incorrect error message is:
device-mapper: table: 254:0: sdb too small for target
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes DM's bio-based vs request-based conditional setting
of next_ordered. For bio-based DM the next_ordered check is no longer a
concern (as that check is now in the __make_request path). For
request-based DM the default of QUEUE_ORDERED_NONE is now appropriate.
bio-based DM was changed to work-around the previously misplaced
next_ordered check with this commit:
99360b4c18
request-based DM does not yet support barriers but reacted to the above
bio-based DM change with this commit:
5d67aa2366
The above changes are no longer needed given Neil Brown's recent fix to
put the next_ordered check in the __make_request path:
db64f680ba
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: NeilBrown <neilb@suse.de>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The recent commit 7513c2a761 (dm raid1:
add is_remote_recovering hook for clusters) changed do_writes() to
update the ms->writes list but forgot to wake up kmirrord to process it.
The rule is that when anything is being added on ms->reads, ms->writes
or ms->failures and the list was empty before we must call
wakeup_mirrord (for immediate processing) or delayed_wake (for delayed
processing). Otherwise the bios could sit on the list indefinitely.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
CC: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Calls to device_init_wakeup should not be necessary in drivers that use
device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag
for the device when initialized.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a
priority tag or vlan tag inserted. Ixgbe driver is currently priority
tagging everything (if packet is not on a VLAN interface).
This patch modifies DCB mode, so that packets marked with skb priority
TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on
the highest priority traffic class.
Programs (like dcbd) can set the skb priority using a socket option. Or, a tc
filter can be configured to set the priority value. Using the value
TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel,
and the bonding LACP code already sets the skb->priority field to this value.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, FCoE offload feature is turned on when the kernel config has
CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn
FCoE offload on when there is FCoE traffic passing and turn it off when
it's just LAN traffic. Since FCoE depends on a lossless network provided
by DCB, this allows us to have FCoE turned on/off when user turns on DCB
using dcbtool.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to the fs_enet driver aa73832c5a
("net: Rework fs_enet driver to use of_mdio infrastructure")
cause kernel crashes when using the mdio-ofgpio driver.
This patch replicates similar changes made to the fs_enet mii-bitbang
drivers. It has been tested on a custom mpc8280 based board using an
NFS mounted root.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It seems that thread_count is not properly calculated in dmatest.
In fact the thread count number that is returned from dmatest_add_threads() is
not correctly added to the thread_count and thus not properly printed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest usually waits for the killing of its kthreads to stop
running tests. This patch adds a parameter that sets a maximum
number of test iterations.
This feature is quite interesting for debugging when you set a lot of
traces in your dmaengine controller driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
According to investigations from windows team ,hw team,
and our test results on all 4x platofrms available
(gm45, g45b, q45, g45a, g45c, g41a, and g41), we find
currently Hot plug live status and Hot plug interrupt
detection are not reliable, sometime the results from
the two approaches are contradicts. So we chose edid
detection for hdmi output.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
at91ether_probe lives in .init.text, so using platform_driver_register
to register it is wrong because binding a device after the init memory
is discarded (e.g. via sysfs) results in an oops.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text as proposed initially.
This saves some memory, but devices registered after the driver is
probed are not bound (probably there are none) and binding via sysfs
isn't possible.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skge hardware is capable of waking up the system from sleep,
enable magic packet WoL during driver initialisation.
This makes WoL work without calling 'ethtool -s ethX wol g'
for each adapter.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Michael Guntsche <mike@it-loops.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tj-block-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch
block: sysfs fix mismatched queue_var_{store,show} in 64bit kernel
ataflop: adjust NULL test
block: fix failfast merge testing in elv_rq_merge_ok()
z2ram: Small cleanup for z2ram.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
sky2: Avoid races in sky2_down
drivers/net/mlx4: Adjust constant
drivers/net: Move a dereference below a NULL test
drivers/net: Move a dereference below a NULL test
connector: maintainer/mail update.
USB host CDC Phonet network interface driver
macsonic, jazzsonic: fix oops on module unload
macsonic: move probe function to .devinit.text
can: switch carrier on if device was stopped while in bus-off state
can: restart device even if dev_alloc_skb() fails
can: sja1000: remove duplicated includes
New device ID for sc92031 [1088:2031]
3c589_cs: re-initialize the multicast in the tc589_reset
Fix error return for setsockopt(SO_TIMESTAMPING)
netxen: fix thermal check and shutdown
netxen: fix deadlock on dev close
netxen: fix context deletion sequence
net: Micrel KS8851 SPI network driver
tcp: Use correct peer adr when copying MD5 keys
tcp: Fix MD5 signature checking on IPv4 mapped sockets
...
fix this build error when CONFIG_MII is not set
drivers/net/ks8851.c:999: undefined reference to `generic_mii_ioctl'
drivers/net/ks8851.c:1050: undefined reference to `mii_link_ok'
drivers/net/ks8851.c:1056: undefined reference to `mii_nway_restart'
drivers/net/ks8851.c:1044: undefined reference to `mii_ethtool_sset'
drivers/net/ks8851.c:1038: undefined reference to `mii_ethtool_gset'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Ben Dooks <ben@simtec.co.uk>
This patch fixes a bug in the non-lro path. Wrong size of received
packet was being passed for updating receive statistics. This patch
is against the net-2.6 git.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0b9da337dc ("Rework
ucc_geth driver to use of_mdio infrastructure") the fixed-link
support is broken.
This patch fixes the support by removing !ug_info->phy_node check,
and adds a call to of_phy_connect_fixed_link() if a phy is not attached
to the MAC.
Also, remove an old fixed-link code that we don't use any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fe192a4911 ("Rework gianfar
driver to use of_mdio infrastructure") the fixed-link support is
broken, the driver oopses at init_phy():
Unable to handle kernel paging request for data at address 0x000000e4
Faulting instruction address: 0xc01cf298
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01cf298] init_phy+0x80/0xdc
LR [c01cf250] init_phy+0x38/0xdc
Call Trace:
[cf81fe80] [c01d1cf8] gfar_enet_open+0x6c/0x19c
[cf81fea0] [c024494c] dev_open+0xfc/0x134
[cf81fec0] [c0242edc] dev_change_flags+0x84/0x1ac
[cf81fee0] [c0399ee0] ic_open_devs+0x168/0x2d8
[cf81ff20] [c039b2e8] ip_auto_config+0x90/0x2a4
[cf81ff60] [c0003884] do_one_initcall+0x34/0x1a8
This patch fixes the oops, and removes phy_node checks, and adds a call
to of_phy_connect_fixed_link() if a phy isn't attached..
Also, remove an old fixed-link code that we don't use any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit aa73832c5a ("Rework
fs_enet driver to use of_mdio infrastructure") the fixed-link support
is broken in the fs_enet driver.
This patch fixes the support by removing a check for phy_node, and adding
a call to of_phy_connect_fixed_link().
Also set netdev parent device via SET_NETDEV_DEV() call, this is needed
so that OF MDIO core could find a node pointer for a device.
Plus, fix "if (IS_ERR(phydev))" check, in case of errors,
of_phy_connect() returns NULL, not ERR_PTR as phy_connect().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed-link support is broken for the ucc_eth, gianfar, and fs_enet
device drivers. The "OF MDIO rework" patches removed most of the
support. Instead of re-adding fixed-link stuff to the drivers, this
patch adds a support function for parsing the fixed-link property
and obtaining a dummy phy to match.
Note: the dummy phy handling in arch/powerpc is a bit of a hack and
needs to be reworked. This function is being added now to solve the
regression in the Ethernet drivers, but it should be considered a
temporary measure until the fixed link handling can be reworked.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent
he loop counter is of type 'unsigned char' and it should count to 128.
The compiler will incorrectly decide that a trivial loop like this:
unsigned char i, ...
for (i = 0; i < 128; i++) {
..
is endless, and will compile it to a single instruction that just
branches to itself.
This was triggered by the addition of '-fno-strict-overflow', and we
could play games with compiler versions and go back to '-fwrapv'
instead, but the trivial way to avoid it is to just make the loop
induction variable be an 'int' instead.
Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure
for digging through assembler differences and finding it.
Reported-and-tested-by: Krzysztof Oledzki <olel@ans.pl>
Found-by: Troy Moure <twmoure@szypr.net>
Gcc-bug-acked-by: Ian Lance Taylor <iant@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't leak kernel stack information through uninitialized structure members.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory
leak after writing lots of data, the kmalloc-96 slab cache keeps
growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush
is never kfreed.
Commit a09485df9c ("ide: move request
type specific code from ide_end_drive_cmd() to callers (v3)") and
f505d49ffd ("ide: fix barriers support")
cause this regression, cmd->rq must now be set for ide_complete_cmd to
honor the IDE_TFLAG_DYN flag.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx. Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E=E1
when != i
if (E == NULL||...) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, then the dereferences should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E=E1
when != i
BUG_ON (E == NULL||...);
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware V4 on CF8381 reports region code shifted by 1 byte to left.
The following patch checks for this and handles it properly.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two users of ar9170 devices have now reported their cards
have been programmed with a regulatory domain of 0x8000.
This is not a valid regulatory domain as such these users were
unable to use these devices. Since this doesn't seem to be
a device EEPROM corruption we must treat it specially. It
may have been possible the manufacturer intended to use 0x0
as the regulatory domain and that would ultimately yield
to US but since we cannot get confirmationf or this we
default this special case to one of our world regulatory
domains, specifically 0x64.
Reported-by: DavidFreeman on #linux-wireless
Reported-by: Joerg Albert <jal2@gmx.de>
Cc: Christian Lamparter <chunkeey@web.de>,
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Tony Yang <tony.yang@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential NULL dereference bug during
error handling in p54spi_probe.
This bug was discovered by smatch:
(http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix another polarity error introduced by the rfkill rewrite,
this time in acer_rfkill_set().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many Nokia handsets support a Phonet interface to the cellular modem
via a vendor-specific USB interface. CDC Phonet follows the
Communications Device Class model, with one control interface, and
and a pair of inactive and active data alternative interface. The later
has two bulk endpoint, one per direction.
This was tested against Nokia E61, Nokia N95, and the existing Phonet
gadget function for the Linux composite USB gadget framework.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the driver data before using it. Fixes an oops when doing rmmod.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to mac_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Various other functions that are called by mac_sonic_probe need to move
to .devinit.text, too.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.
Testedy-by: Steven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit below changed the semantics of rt2x00_check_rev so that it no
longer checked the bottom 4 bits of the rev were non-zero. During that
conversion this part of the check was not propogated to the rt2500usb
initialisation.
commit 358623c22c
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Tue May 5 19:46:08 2009 +0200
rt2x00: Simplify rt2x00_check_rev
Without this check rt73 devices are miss recognised as rt2500 devices and
two drivers are loaded. Preventing the device being used. Reinstate this
check.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel
may oops when the module is unloaded as the workqueue for led_on was
not being cancelled.
This patch fixes the problem reported in
http://marc.info/?l=linux-wireless&m=124742957615781&w=2.
Reported-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported some issues with using AP mode without
nohwcrypt=1. Most likely this is similar to the problem fixed
some time ago in ath9k by 3f53dd64f1,
"ath9k: Fix hw crypto configuration for TKIP in AP mode."
That only affects TKIP but it's easiest to just disable that and
WEP too until we get a proper fix in.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the "data" pointer is freed, we can't be iterating
to the next item in the list any more so we need to use
list_for_each_entry_safe with a temporary variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you rmmod the module while associated, frames might
be transmitted during unregistration -- which will crash
if the hwsim%d interface is unregistered first, so only
do that after all the virtual wiphys are gone.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The byte count table is only used for aggregation. Updating it
in other cases caused fragmented frames to be dropped.
This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the power_level file to adhere to the "one value
per file" sysfs rule. The user will know which power level was
requested as it will be the number just written to this file. It
is thus not necessary to create a new sysfs file for this value.
In addition it fixes a problem where powertop's parsing expects
this value to be the first value in this file without any descriptions.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver private data is now based on wiphy. So we should not
touch the private data after wiphy_free() is called. The patch
fixes the potential NULL pointer dereference by making the
iwm_wdev_free() the last one on the interface removal path.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.
Added quirk data for forced release keys.
BugLink: https://bugs.launchpad.net//bugs/397499
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Standard data flow for MMC/SD/SDIO cards requires that the mvsdio
controller be set for big endian operation. This is causing problems
with buffers which length is not a multiple of 4 bytes as the last
partial word doesn't get shifted all the way and stored properly in
memory. Let's compensate for this.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function does not have an error return and returning an error is
instead interpreted as having a lot of pending bytes.
Reported by Jeff Harris who provided a list of some of the remaining
offenders.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not
need to save the interrupt state, so it is changed to a simple
spin_lock.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression lock1,lock2;
expression flags;
@@
*spin_lock_irqsave(lock1,flags)
... when != flags
*spin_lock_irqsave(lock2,flags)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The buffer for the consoles are unconditionally allocated at con_init()
time, which miss the creation of the vcs(a) devices.
Since 2.6.30 (commit 4995f8ef9d, 'vcs:
hook sysfs devices into object lifetime instead of "binding"' to be
exact) these devices are no longer created at open() and removed on
close(), but controlled by the lifetime of the buffers.
Reported-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Tested-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Cc: stable@kernel.org
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@skynet.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/can/sja1000/sja1000.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)
Cc: rain_maker@root-forum.org
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c589_cs:
re-initialize the multicast in the tc589_reset,
and spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.
Old code was only monitoring temperature for function 0 only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: fix deadlock on dev close
The tx ring accounting fix in commit cb2107be43
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mac driver support for evaluation board based on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, then the dereferences should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E=E1
when != i
if (E == NULL||...) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The variable virtio_blk references the function virtblk_probe() (which
is in .devinit section) and also references the function
virtblk_remove() ( which is in .devexit section). So, virtio_blk
simultaneously refers .devinit and .devexit section. To avoid this
messup, we mark virtio_blk as __refdata.
We were warned by the following warning:
LD drivers/block/built-in.o
WARNING: drivers/block/built-in.o(.data+0xc8dc): Section mismatch in
reference from the variable virtio_blk to the function
.devinit.text:virtblk_probe()
The variable virtio_blk references
the function __devinit virtblk_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: drivers/block/built-in.o(.data+0xc8e0): Section mismatch in
reference from the variable virtio_blk to the function
.devexit.text:virtblk_remove()
The variable virtio_blk references
the function __devexit virtblk_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Move a dereference below a NULL test
fb/intelfb: conflict with DRM_I915 and hide by default
drm/ttm: fix misplaced parentheses
drm/via: Fix vblank IRQ on VIA hardware.
drm: drm_gem, check kzalloc retval
drm: drm_debugfs, check kmalloc retval
drm/radeon: add some missing pci ids
If kthread_run() fails or never gets to run we'll have NULL
or a pointer encoded error in kenvctrld_task, rather than
a legitimate task pointer.
So this makes bbc_envctrl_cleanup() crash as it passed this
bogus pointer into kthread_stop().
Reported-by: BERTRAND Joël <joel.bertrand@systella.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>