First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
-----BEGIN PGP SIGNATURE-----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=FCgU
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
arm64: allwinner: a64: add Ethernet PHY regulator for several boards
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
-----BEGIN PGP SIGNATURE-----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=kmQd
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dtc points out that the parent node of the interrupt controllers is not
actually an interrupt controller itself, and lacks an #interrupt-cells
property:
arch/arm/boot/dts/tango4-vantage-1172.dtb: Warning (interrupts_property): Missing #interrupt-cells in interrupt-parent /soc/interrupt-controller@6e000
This removes the annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
work on DM365 and a fix for battery voltage monitoring on Lego EV3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GZm0
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "TI DaVinci fixes for v4.15" from Sekhar Nori:
DaVinci fixes for v4.15 consiting of fixes to make EDMA and MMC/SD
work on DM365 and a fix for battery voltage monitoring on Lego EV3.
* tag 'davinci-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix mmc entries in dm365's dma_slave_map
ARM: dts: da850-lego-ev3: Fix battery voltage gpio
ARM: davinci: Add dma_mask to dm365's eDMA device
ARM: davinci: Use platform_device_register_full() to create pdev for dm365's eDMA
Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.
And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlosSekQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgcERB/9hWGZwQAexlfJj4mnAl61axE+KROHSsDFd
qrQqTX9LLbNr+Ot769w5okRWo1C3ItSWAGvy08Wksrx2Yq5y0RvbGeCA4CjpKxDA
jO1Aphe43rFXk3oMbRAnrr8zVMHjQZO0OCvyEfbQYZSr/uXV+wzNj9/Ll54xNFJd
6hwF+X/XGsQHOh7k6BrzWeXmpnIZ3s72EN7uIHg58HCa97Xnwwa25HR0UEIhR43F
BmP/1AID/JfALu0+F/VF2vnYeC8JL46/fX+xmi6YzsnRLOiCKIZMjuFBAQk7rE4/
qjSd7Xqi3F3c61wvnHw4s6QkHOFi48pJJfykEorV5yi7Yk9Kad4G
=I63w
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.15" from Heiko Stübner:
Another trailing interrupt-cell 0 removed.
Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.
And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.
* tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: limit rk3328-rock64 gmac speed to 100MBit for now
arm64: dts: rockchip: remove vdd_log from rk3399-puma
arm64: dts: rockchip: fix trailing 0 in rk3328 tsadc interrupts
on the rk3066a-marsboard to make it not fail from cpufreq changes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlosSE4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRhMCACXcPJmWvjPRQwrpFrFOrHUfgsku46CFl2a
AWmN5wGB2pStM1R/1HsfrfO0YXb5e9UESEwyQzb1/DEoAnES5aFrZqnuPSSHr/9W
cZR8fDRk69cxMILdCy25xmWeAmhPTJUWTPwdhfSkINmf0+DcPehKr97xVyzEcVK3
LMczvzPUSuipciQbVdR8bTkVy05ToHJctN+ri3Ux9SqrGZcW86W/v5mRnRVxxvXU
NcdEIB1/IC9nHPYYRJbUvrEgLIzHt21KkS3GEmCI3kf4t7qsY28VkVfsoqrIQMA9
/ennO0r6df+7sSzQXI25lERWMHk+gSSlq4z3jguI6b8NmAFBynMh
=CZn2
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.15" from Heiko Stübner:
Removed another trailing interrupt-cell 0 and added the cpu regulator
on the rk3066a-marsboard to make it not fail from cpufreq changes.
* tag 'v4.15-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix rk3288 iep-IOMMU interrupts property cells
ARM: dts: rockchip: add cpu0-regulator on rk3066a-marsboard
This should have always been 8.
Fixes: db4d6d9d80fa ("ARM: dts: aspeed: Correctly order UART nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 1cb686c08d12 ("ARM: dts: exynos: Add status property to Exynos 542x
Mixer nodes") disabled the Mixer node by default in the DTSI and enabled
for each Exynos 542x DTS. But unfortunately it missed to enable it for the
Exynos5800 Peach Pi machine, since the 5800 is also an 542x SoC variant.
Fixes: 1cb686c08d12 ("ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When we added the regulator support in commit 90c5d7cdae64 ("ARM: dts:
sun8i: a711: Add regulator support"), we also dropped the PMIC's
compatible. Since it's not in the PMIC DTSI, unlike most other PMIC
DTSI, it obviously wasn't probing anymore.
Re-add it so that everything works again.
Fixes: 90c5d7cdae64 ("ARM: dts: sun8i: a711: Add regulator support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
-----BEGIN PGP SIGNATURE-----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=xHta
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a bunch of fixes CCN and (guest starring this time) CCI drivers.
* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
attributes constification
The one fixing potential issues have been cc-ed to stable.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJaJYRMExxwYXdlbC5tb2xsQGFybS5jb20ACgkQv2NFol9drk+D
MAf7BbBQS5Bx2cT8gb7hlOFQa72io5i26E6vw46xumS6LmycynK1MuX9NSNpClYN
zRNT6qitovWwLeicd+Dh5XL2371rjORa7TNfZt/CiyRB8W+fix5RnlZuSfpEeCcc
dGGtUoz0PETblp9ovCAqWEmxUn2vs9+hRlPg+fxIJBDP34MnwwLTaDioalaBLbn5
GxDBwwrdv1PEnOL0dwuhNcg94+pdHqg21BXIfDwcbzus/fiTcCUbjsoMr7TXPmCY
0PaEOrTIdPIBxvpeZogqZ2GkQQucW+4FKq281UXCDmS7BsP3V7OsqhelSVAwe2jE
LjzCJlf6YBTIx7OXffB7yukvnw==
=K2m2
-----END PGP SIGNATURE-----
Merge tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
bus: ARM CCN and CCI PMU driver fixes
This is a bunch of fixes CCN and (guest starring this time) CCI drivers.
* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
attributes constification
The one fixing potential issues have been cc-ed to stable.
* tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
bus: arm-cci: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Simplify code
bus: arm-ccn: Check memory allocation failure
bus: arm-ccn: constify attribute_group structures.
Signed-off-by: Olof Johansson <olof@lixom.net>
These recently started showing up with better dtc checks being
introduced.
-----BEGIN PGP SIGNATURE-----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=BHn4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for dts compiler warnings
These recently started showing up with better dtc checks being
introduced.
* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
The clock-names for pclk was wrongly set to "core", but the bindings
specifies "pclk".
This was not cathed until the legacy non-documented bindings were removed.
Reported-by: Andreas Färber <afaerber@suse.de>
Fixes: f72d6f6037b7 ("ARM64: dts: meson-gx: use stable UART bindings with correct gate clock")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
fix mmc entries in dm365's dma_slave_map to match the actual device names
Fixes: 0c750e1fe481 ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Alejandro Mery <amery@hanoverdisplays.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In configurations without CONFIG_OMAP3 but with secure RAM support,
we now run into a link failure:
arch/arm/mach-omap2/omap-secure.o: In function `omap3_save_secure_ram':
omap-secure.c:(.text+0x130): undefined reference to `save_secure_ram_context'
The omap3_save_secure_ram() function is only called from the OMAP34xx
power management code, so we can simply hide that function in the
appropriate #ifdef.
Fixes: d09220a887f7 ("ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context")
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in nspire dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes the battery voltage monitoring gpio-hog settings.
When the gpio is low, it turns off the battery voltage to the ADC chip.
However, this needs to be on all of the time so that we can monitor
battery voltage.
Also, there was a typo that prevented pinmuxing from working correctly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add dma_mask to dm365's EDMA device.
Without a valid dma_mask, EDMA on DM365 refuses to
probe.
Fixes: cef5b0da4019 ("ARM: davinci: Add dma_mask to eDMA devices")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Alejandro Mery <amery@hanoverdisplays.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Convert the DM365 EDMA platform device creation to use
struct platform_device_info XXXXXX __initconst and
platform_device_register_full()
This will allow us to specify the dma_mask for the device
in an upcoming patch. Without this, EDMA on DM365 refuses
to probe.
Fixes: 7ab388e85faa ("ARM: davinci: Use platform_device_register_full() to create pdev for eDMA")
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Alejandro Mery <amery@hanoverdisplays.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It looks like either the current kernel or the hardware has reliability
issues when the gmac is actually running at 1GBit. In my test-case
it is not able to boot on a nfsroot at this speed, as the system
will always lose the connection to the nfs-server during boot, before
reaching any login prompt and not recover from this.
So until this is solved, limit the speed to 100MBit as with this the
nfsroot survives stress tests like an apt-get upgrade without problems.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We have phy-cells for usb_phy0, but it's missing for usb_phy1 and we get:
Warning (phys_property): Missing property '#phy-cells' in node
/ocp/l4ls@48000000/control@140000/usb-phy@1b00 or bad phandle
(referred from /ocp/usb@47400000/usb@47401800:phys[0])
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sdcard detect pin on orange-pi-zero-plus2 is pulled up.
Fix cd-gpio description to enable sdcard detect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators,
replace fixed regulator vcc3v3 with AXP803 dcdc1 regulator where ever
it need to replace.
Tested mmc0 on sopine baseboard.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When the HDMI controller device node was added, the needed PLL clock
macros were not exported. A separate patch addresses that, but it is
merged through a different tree.
Now that both patches are in mainline proper, we can convert the raw
numbers to proper macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Include the OF-based modalias in the uevent sent when registering devices
on the sunxi RSB bus, so that user space has a chance to autoload the
kernel module for the device.
Fixes a regression caused by commit 3f241bfa60bd ("arm64: allwinner: a64:
pine64: Use dcdc1 regulator for mmc0"). When the axp20x-rsb module for
the AXP803 PMIC is built as a module, it is not loaded and the system
ends up with an disfunctional MMC controller.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Cc: stable <stable@vger.kernel.org> # 4.4.x 7a3b7cd332db of: device: Export of_device_{get_modalias, uvent_modalias} to modules
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The I2C adapter driver is sometimes slow, causing the SCL line to
be stuck low for more than the stipulated SMBUS timeout of 25-35 ms.
This causes the client device to give up which in turn causes silent
corruption of data. So, disable the SMBUS timeout in the client device.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Probably due to some copy-paste mistake, the tsadc of rk3328 ended up
with a 0 as 4th element that shouldn't be there, as interrupts on the
rk3328 only have multiples of 3, making dtc complain. So remove it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ARM CCI driver seem to be using smp_processor_id() in a
preemptible context, which is likely to make a DEBUG_PREMPT
kernel scream at boot time.
Turn this into a get_cpu()/put_cpu() that extends over the CPU
hotplug registration, making sure that we don't race against
a CPU down operation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Booting a DEBUG_PREEMPT enabled kernel on a CCN-based system
results in the following splat:
[...]
arm-ccn e8000000.ccn: No access to interrupts, using timer.
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x1c/0x28
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.13.0 #6111
Hardware name: AMD Seattle/Seattle, BIOS 17:08:23 Jun 26 2017
Call trace:
[<ffff000008089e78>] dump_backtrace+0x0/0x278
[<ffff00000808a22c>] show_stack+0x24/0x30
[<ffff000008bc3bc4>] dump_stack+0x8c/0xb0
[<ffff00000852b534>] check_preemption_disabled+0xfc/0x100
[<ffff00000852b554>] debug_smp_processor_id+0x1c/0x28
[<ffff000008551bd8>] arm_ccn_probe+0x358/0x4f0
[...]
as we use smp_processor_id() in the wrong context.
Turn this into a get_cpu()/put_cpu() that extends over the CPU hotplug
registration, making sure that we don't race against a CPU down operation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Use 'devm_kasprintf()' to simplify the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9074 5592 416 15082 3aea drivers/bus/arm-ccn.o
File size After adding 'const':
text data bss dec hex filename
9327 5336 416 15079 3ae7 drivers/bus/arm-ccn.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The interrupts property in the iep-IOMMU node for the rk3288 dts file has a
spurious extra cell causing a dtc warning:
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff900800
Remove the extra cell.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Revert "Merge tag 'scpi-updates-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers"
Paraphrased from email from Kevin Hilman:
Revert ARM SCPI changes since v4.14.
Untested changes caused regressions in SCPI and CPUfreq/DVFS failures
on most Amlogic SoCs. Changes reverted for v4.15 so they can be better
reviewed and tested.
These ARM SCPI changes caused SCPI regressions resulting in CPUfreq
failures on most Amlogic SoCs (found by kernelci.org.)
Unfortunately, this was not caught in linux-next due to other bugs/panics
on these platforms masking this problem so we've only found it since
we've fixed the other issues.
Since we're already in the -rc cycle, I'd prefer to revert to a known
working state (that of v4.14) rather than finding/reverting a subset,
which would just lead to another untested state.
These changes can then have some time to be better reviewed and tested
and resubmitted for v4.16.
Kevin Hilman has tested this revert on the affected Amlogic SoCs and
verified that we're back to the previous (working) condition.
This reverts commit 6710acf2596a29f7351e8165d981645f403e0025, reversing
changes made to 4b367f2e8854da34d14bd154ff4432fb49f69b36.
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:
- Fix smatch issue introduced by recent omap device changes for legacy
resources
- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
devices found by pending CMA changes. While it seems that we have not hit
this in other use cases, let's fix it to avoid a nasty and hard to find
suprise as right now there is just luck keeping the SRAM virtual address
to physical address translation working with the 0xffff high_mask.
- Fix am335x reading of domain state registers that only exist for the
PM_CEFUSE domain and produce wrong results for other domains
- Fix missing setting for error code for omap device if allocation fails
- Fix missing modules_offs for omap3 MMC3 affecting n9/n950
- Fix cm_split_idlest() reading reserved registers showing wrong
idlestatus
- Fixes to correct #phy-cells property for compiler warnings that
recently started happening
- Add a missing OHCI remote-wakeup-connected property that I was supposed
to merge after the ohci-omap3 to ohci-platform changes but somehow managed
to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
and modem hang
- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
typically happened within 20 - 40 minutes on an idle system. This turned
out to be an issue caused by using the parent interrupt controller directly
with the WUGEN + GIC stacked interrupt controller domains
- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
have been broken since we changed GPMC to use the interrupt controller
binding for some pins. And fix the wrong pin muxing for WLAN while at it
- Fixes for am437x interrupt and dma properties to fix compiler warnings
that recently started happening
* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
ARM: dts: am4372: Correct the interrupts_properties of McASP
ARM: dts: logicpd-somlv: Fix wl127x pinmux
ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
ARM: OMAP2+: Missing error code in omap_device_build()
ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
ARM: dts: Add remote-wakeup-connected for omap OHCI
ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
ARM: OMAP2+: Fix smatch found issue for omap_device
ARM: OMAP2/3: CM: fix cm_split_idlest functionality
ARM: OMAP3: hwmod_data: add missing module_offs for MMC3
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaH174AAoJEFBXWFqHsHzOL+kIALWexxxRlwyOl75pkkZKTX2m
AsvVTq3jgjvNTJn8mjuhzYstgUr0/GqX1InG7eBeJwQPQj+mn1roElkd1wz09xXY
lKECXbTwQ0+Jc8Diomms5VvBD3y3OwaQVZKAPbTfI6A4nuUCaQdUVDMplP6dCoTI
FUcxbOvAppAFEeC3X04Gc2OdUpBRSiio8DE5nvuIGzIRvA9auc5YTbJ9sOtduj4o
lZvVgAHqccTmFgaFfPdW6T7h7uyZ1Jz5ItDx3BTk+QtWxFq+Cb9hOEJg/I+Z6QY+
2twJZxyXgpaWmdQkP18tSOEA8dGZDwIwhRG1ZEeeY0JNPw6dy5w9j1W1zijdCIk=
=RRYB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.15:
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
Revert "ARM: dts: imx53: add srtc node"
ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>
* Fixes problem with an invalid call to of_node_put() in
optee_driver_init()
-----BEGIN PGP SIGNATURE-----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=ZnSP
-----END PGP SIGNATURE-----
Merge tag 'tee-drv-fix-for-4.15' of https://git.linaro.org/people/jens.wiklander/linux-tee into fixes
One small fix for optee_driver_init()
* Fixes problem with an invalid call to of_node_put() in
optee_driver_init()
* tag 'tee-drv-fix-for-4.15' of https://git.linaro.org/people/jens.wiklander/linux-tee:
optee: fix invalid of_node_put() in optee_driver_init()
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
-----BEGIN PGP SIGNATURE-----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=A6Ju
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix PPI interrupt types
ARM: dts: NSP: Disable AHCI controller for HR NSP boards
ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC DT Fixes for v4.15
Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.
* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in Marvell dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The list is almost sorted. Move "lg" up to complete it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The rk3066 also has operating points now, but without adjusting
the cpu-regulator will break once higher voltages are needed for
a specific frequency, so add the needed cpu0-regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>