Only root should have write permission on sysfs file ab8500_chargalg/chargalg.
Cc: stable@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no support to measure the main charger voltage and
current using AB9540 gpadc. Therefore this has been removed
from the driver.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Fix the way interrupts are handled within the PM2301 charging driver.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Olivier CLERGEAUD <olivier.clergeaud@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
When the charging safety timer elapses, the battery health is
shown as "Good". This is misleading and also makes it difficult
to distinguish issues relating to discharging despite the fact
that the charger is still connected.
When in actual fact a safety timer elapse is an indication of a
fault in the battery. Here we make this clearer by reporting
POWER_SUPPLY_HEALTH_UNSPEC_FAILURE instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add AB9540 and AB8505 support to ABx500 BTEMP driver.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Changed conditions for restarting low battery measurements counter
and adjusted the interval between measurements to avoid RF burst
induced voltage drops, and to shorten time to decide to shut down.
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Signed-off-by: Martin Bergstrom <martin.bergstrom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
AB8500 refuses to start charging when some types of non standard
chargers are connected. This change force the AB to start charging.
Signed-off-by: Henrik Sölver <henrik.solver@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Yvan FILLION <yvan.fillion@stericsson.com>
AC charger driver for the DB9540 based platforms.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
GPLv2+ is not a valid license string. Replace it with one that is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
As HZ is a full-second, there is little point in rounding it.
Let's save a few cycles by using HZ directly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When calculating the average current the nominator will
overflow when the charging current is high.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Henrik Sölver <henrik.solver@stericsson.com>
Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
A Legacy USB charger should be handled directly by the charger
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Cleanup of the ab8500_charger driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add support for the battery over-voltage situation
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
BTEMP thermal compensation factor times 10 is applied in two places, probe
and get_property. Removed from probe.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Round the capacity values for better enduser experience.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: pender01 <peter.enderborg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The Travel and Carkit adapter should be handled directly by
the charger driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Ignore the low btemp interrupts for ab8500 3.0 and 3.3
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The Linux Power Supply framework expects battery temperatures to have
a resolution of 0.1 degree Celsius; however, the AB8500 btemp driver
supplies a battery temperature resolution of 1 degree Celsius. We
therefore have to use a factor 10 on the measured values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
In case of time out error IRQ needs to be disabled
otherwise we will get unbalanced enable/disable pairs.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Gracefully handle gpadc conversion errors.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Johan BJORNSTEDT <johan.bjornstedt@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Doing so provides a greater degree of accuracy when dealing with
time-frames between 1us and 20ms. msleep() is only accurate for
wake-ups greater than 20ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Johan BJORNSTEDT <johan.bjornstedt@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add two new work queues to provide USB and AC charger disconnect
detection.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Rename the ab8500_power_loss_handling function to a more
descriptive name ab8500_enable_disable_sw_fallback
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Tested-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Avoid accessing vc_tbl_ref[3], which is one past the end of that array, in
da9052_determine_vc_tbl_index(), by adjusting the loop bound.
(Hint: there is 'i + 1' inside the loop.)
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
use devm_kzalloc and no need of error path and unload frees.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Use 'platform_device' in kernel messages rather than i2c client device
node. lp8788_update_charger_params() needs additional argument, 'pdev'.
Then, remove unnecessary lp8788 private data in lp8788_irq_register().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The lp8788-charger is a platform driver of lp8788-mfd. The platform device
is allocated when mfd_add_devices() is called in lp8788-mfd. On the other
hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case of
resource managed mem alloc and device kernel message.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example,
power-off by restarting to letting u-boot hold the SoC until the user
presses a key. Add a generic driver to implement this. It binds a function
to pm_power_off, which calls arm_pm_restart.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The QNAP NAS boxes have a microcontroller attached to the SoCs second
serial port. By sending it a simple command, it will turn the power for
the board off. This driver registers a function for pm_power_off to send
such a command.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
devm_kzalloc should not be followed by kfree, as this results in a double
free. The problem was found using the following semantic match
(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression x,e;
@@
x = devm_kzalloc(...)
... when != x = e
?-kfree(x,...);
// </smpl>
Furthermore, in the remove function, the calls to free_irq are moved up to
prevent a possible reference in the interrupt handler to resources freed by
power_supply_unregister.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
commit a66f59ba2e
bq27x00_battery: Add support for BQ27425 chip
introduced 2 bugs.
1/ 'chip' was set to BQ27425 unconditionally - breaking support for
other devices;
2/ BQ27425 does not support cycle count, how the code still tries to
get the cycle count for BQ27425, and now does it twice for other chips.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Saranya Gopal <saranya.gopal@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
As most of the charger chips come with two kinds of safety features
related to timing:
1. Watchdog Timer (interms of seconds/mins)
2. Safety Timer (interms of hours)
This patch adds these to fault causes in POWER_SUPPLY_PROP_HEALTH_* enums
so that whenever there is either watchdog timeout or safety timer timeout
driver could notify the user space accurately about the fault and will
also be helpful for debug.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
devm_kzalloc is device managed and makes error handling and code cleanup a
bit simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
module_i2c_driver() makes the code simpler by eliminating module_init and
module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests and rewrite _setup_polling() so that
it uses mod_delayed_work() if the next polling interval is sooner than
currently scheduled. queue_delayed_work() is used otherwise.
Only compile tested. I noticed that two work items - setup_polling
and cm_monitor_work - schedule each other. It's a very unusual
construct and I'm fairly sure it's racy. You can't break such
circular dependency by calling cancel on each. I strongly recommend
revising the mechanism.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch split _probe function for readability because _probe function
is longer than 400 line.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be probed. It
was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=hppb
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6
Pull battery update, part 2, from Anton Vorontsov:
"These are left overs that I didn't have time to review/apply before
the merge window opened. I didn't want to "spoil" the first pull
request with these late patches, so they were not included:
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be
probed. It was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling."
* tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6:
charger-manager: Fix bug when check dropped voltage after fullbatt event
charger-manager: Fix bug related to checking fully charged state of battery
ARM: OMAP: rx51: Register platform device for rx51_battery
The cpu_is_omap macros are now local to arch/arm/mach-omap2
in soc.h and plat/cpu.h can finally be dropped for omap2+.
Thanks everybody for help with fixing the drivers.
Note that we can now also remove the unused plat/cpu.h from
smartreflex.c and isp.c as they will cause compile errors
with ARCH_MULTIPLATFORM enabled.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch check difference value between current voltage of battery and
desc->fullbatt_uV whether positve or negative number. If difference value
is negative number when current voltage of battery is larger than
desc->fullbatt_uV, charger-manager return immediately because battery is
fully charged.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch fix bug related to checking fully charged state of battery when
charger-manager call is_full_charged() function. After reading property of
charger/fuel-gauge through power_supply API, val.intval is more than 1.
So, is_full_charged() function always return true. If true, battery means
fully charged state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
