The multicast variable in the ieee80211_accept_frame() function is
treated as a boolean, but defined as int. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the enum definitions are unnamed but there's still
an attempt at documenting them - that doesn't work. Name
them to make that work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the definition for FT-8021.1X AKM selector as defined in
IEEE Std 802.11-2016, table 9-133.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the definitions for SUITE_B and SUITE_B_192 AKM selectors as
defined in IEEE802.11REVmc_D5.0, table 9-132.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The monitor mode delivery logic makes it hard to add any
kind of filtering in an efficient way, because the monitor
SKB is created first and then passed to all interfaces.
Rewrite the logic to create the monitor SKB the first time
it's actually needed, and then keep delivering it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When part of a bigger bandwidth (160 MHz) channel falls in DFS
channel range it is possible that the center frequency may not
necessarily be a radar channel. Remove the sanity check on channel
flag for IEEE80211_CHAN_RADAR in regulatory_propagate_dfs_state(),
this should fix the dfs state propagation for non-DFS center freq
which has DFS channels in it's bandwidth, should also fix unnecessary
WARN_ON() spam in regulatory_propagate_dfs_state().
Fixes: 8976672736 ("cfg80211: Share Channel DFS state across wiphys of same DFS domain")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return error code -ENODEV from the no PHY found error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a generic SKB based non-optimized XDP path which is used
if either the driver lacks a specific XDP implementation, or the user
requests it via a new IFLA_XDP_FLAGS value named XDP_FLAGS_SKB_MODE.
It is arguable that perhaps I should have required something like
this as part of the initial XDP feature merge.
I believe this is critical for two reasons:
1) Accessibility. More people can play with XDP with less
dependencies. Yes I know we have XDP support in virtio_net, but
that just creates another depedency for learning how to use this
facility.
I wrote this to make life easier for the XDP newbies.
2) As a model for what the expected semantics are. If there is a pure
generic core implementation, it serves as a semantic example for
driver folks adding XDP support.
One thing I have not tried to address here is the issue of
XDP_PACKET_HEADROOM, thanks to Daniel for spotting that. It seems
incredibly expensive to do a skb_cow(skb, XDP_PACKET_HEADROOM) or
whatever even if the XDP program doesn't try to push headers at all.
I think we really need the verifier to somehow propagate whether
certain XDP helpers are used or not.
v5:
- Handle both negative and positive offset after running prog
- Fix mac length in XDP_TX case (Alexei)
- Use rcu_dereference_protected() in free_netdev (kbuild test robot)
v4:
- Fix MAC header adjustmnet before calling prog (David Ahern)
- Disable LRO when generic XDP is installed (Michael Chan)
- Bypass qdisc et al. on XDP_TX and record the event (Alexei)
- Do not perform generic XDP on reinjected packets (DaveM)
v3:
- Make sure XDP program sees packet at MAC header, push back MAC
header if we do XDP_TX. (Alexei)
- Elide GRO when generic XDP is in use. (Alexei)
- Add XDP_FLAG_SKB_MODE flag which the user can use to request generic
XDP even if the driver has an XDP implementation. (Alexei)
- Report whether SKB mode is in use in rtnl_xdp_fill() via XDP_FLAGS
attribute. (Daniel)
v2:
- Add some "fall through" comments in switch statements based
upon feedback from Andrew Lunn
- Use RCU for generic xdp_prog, thanks to Johannes Berg.
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: b5a9ee7cf3 ("qed: Revise QM configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When iterating through a map, we need to find a key that does not exist
in the map so map_get_next_key will give us the first key of the map.
This often requires a lot of guessing in production systems.
This patch makes map_get_next_key return the first key when the key
pointer in the parameter is NULL.
Signed-off-by: Teng Qin <qinteng@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return falue form sock_fanout_open is -1, not zero. One test
case was checking for 0 instead of -1.
Tested: Built and tested in clean client.
Signed-off-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is unused and probably was unintentionally left while
moving completion queue mapping in submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
qed/qede: VF tunnelling support
With this series VFs can run vxlan/geneve/gre tunnels over it.
Please consider applying this series to "net-next"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures UDP ports locally instead of
configuring them in deferred context which would be
helpful in synchronizing UDP ports configuration for VFs
which will be enabled in further patches.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables tunnel offloads via ndo_features_check()
if given UDP port is not offloaded to hardware. This in turn
allows to run multiple tunnel interfaces using different UDP ports.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: add informations about l2tpeth interfaces in /sys
Patch #1 lets userspace retrieve the naming scheme of an l2tpeth
interface, using /sys/class/net/<iface>/name_assign_type.
Patch #2 adds the DEVTYPE field in /sys/class/net/<iface>/uevent so
that userspace can reliably know if a device is an l2tpeth interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Export type of l2tpeth interfaces to userspace
(/sys/class/net/<iface>/uevent).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export naming scheme used when creating l2tpeth interfaces
(/sys/class/net/<iface>/name_assign_type). This let userspace know if
the device's name has been generated automatically or defined manually.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
per discussion at netconf/netdev:
When we have an action that is capable of branching (example a policer),
we can achieve a continuation of the action graph by programming a
"continue" where we find an exact replica of the same filter rule with a lower
priority and the remainder of the action graph. When you have 100s of thousands
of filters which require such a feature it gets very inefficient to do two
lookups.
This patch completes a leftover feature of action codes. Its time has come.
Example below where a user labels packets with a different skbmark on ingress
of a port depending on whether they have/not exceeded the configured rate.
This mark is then used to make further decisions on some egress port.
#rate control, very low so we can easily see the effect
sudo $TC actions add action police rate 1kbit burst 90k \
conform-exceed pipe/jump 2 index 10
# skbedit index 11 will be used if the user conforms
sudo $TC actions add action skbedit mark 11 ok index 11
# skbedit index 12 will be used if the user does not conform
sudo $TC actions add action skbedit mark 12 ok index 12
#lets bind the user ..
sudo $TC filter add dev $ETH parent ffff: protocol ip prio 8 u32 \
match ip dst 127.0.0.8/32 flowid 1:10 \
action police index 10 \
action skbedit index 11 \
action skbedit index 12
#run a ping -f and see what happens..
#
jhs@foobar:~$ sudo $TC -s filter ls dev $ETH parent ffff: protocol ip
filter pref 8 u32
filter pref 8 u32 fh 800: ht divisor 1
filter pref 8 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10 (rule hit 2800 success 1005)
match 7f000008/ffffffff at 16 (success 1005 )
action order 1: police 0xa rate 1Kbit burst 23440b mtu 2Kb action pipe/jump 2 overhead 0b
ref 2 bind 1 installed 207 sec used 122 sec
Action statistics:
Sent 84420 bytes 1005 pkt (dropped 0, overlimits 721 requeues 0)
backlog 0b 0p requeues 0
action order 2: skbedit mark 11 pass
index 11 ref 2 bind 1 installed 204 sec used 122 sec
Action statistics:
Sent 60564 bytes 721 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 3: skbedit mark 12 pass
index 12 ref 2 bind 1 installed 201 sec used 122 sec
Action statistics:
Sent 23856 bytes 284 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Not bad, about 28% non-conforming packets..
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlj/Cw8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9keOB/9dFFKUSqXEbevRCVj8Hc/tpmUnAYDP
xcIpz/8GRHPrkOx/tpqtzkAQjeiNzcrT5LDPLDoMSpubZDJjNTKGfcb5sOvGqK9P
IyY4dv0DO9/z1zxdpkK7CkR+g9Z3w9mEdQl2OS0yxbOXRPgX5Sl44Tp5xWgvJhOc
s60m/Y60PQ22CSee7EBYWCwvJPfLIdsr5AIM6wtbEveZU13afAFbyIqoP/97RZKF
sJ8NfGwQmRcD+AHw1nB/YfhNh4NEBE52IiBKf3zgC8Y8lDId/Wve/j/MnJGzeK48
eXPU3g1QaJTuEddn4xC0RRMKycR9klwfGJkY1cKSLtCWQxd1cfHKLdWY
=P474
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.12-20170425' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-04-25
this is a pull request of 21 patches for net-next/master.
There are 4 patches by Stephane Grosjean for the PEAK PCAN-PCIe FD
CAN-FD boards. The next 7 patches are by Mario Huettel, which add
support for M_CAN IP version >= v3.1.x to the m_can driver. A patch by
Remigiusz Kołłątaj adds support for the Microchip CAN BUS Analyzer. 8
patches by Oliver Hartkopp complete the initial CAN network namespace
support. Wei Yongjun's patch for the ti_hecc driver fixes the return
value check in the probe function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4fbae7d83c ("ipvlan: Introduce l3s mode") added
registration of netfilter hooks via nf_register_hooks().
This API provides the illusion of 'global' netfilter hooks by placing the
hooks in all current and future network namespaces.
In case of ipvlan the hook appears to be only needed in the namespace
that contains the ipvlan master device (i.e., usually init_net), so
placing them in all namespaces is not needed.
This switches ipvlan driver to pernet operations, and then only registers
hooks in namespaces where a ipvlan master device is set to l3s mode.
Extra care has to be taken when the master device is moved to another
namespace, as we might have to 'move' the netfilter hooks too.
This is done by storing the namespace the ipvlan port was created in.
On REGISTER event, do (un)register operations in the old/new namespaces.
This will also allow removal of the nf_register_hooks() in a future patch.
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: dabf54dd1c ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Autoload the vcan module when a vcan instance is to be created by
'ip link add type vcan'
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
See Kconfig entry for details.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN gateway was not implemented as per-net in the initial network
namespace support by Mario Kicherer (8e8cda6d73).
This patch enables the CAN gateway to be used in different namespaces.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_BCM protocol and its procfs entries were not implemented as per-net
in the initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net functionality for the CAN BCM.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statistics and its proc output was not implemented as per-net in the
initial network namespace support by Mario Kicherer (8e8cda6d73).
This patch adds the missing per-net statistics for the CAN subsystem.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_rx_alldev_list is a per-net data structure now. Remove it's definition
here and can_rx_dev_list too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The namespace support for the CAN subsystem does not need any additional
memory. So when ".size = 0" there's no extra memory allocated by the system.
And therefore ".id" is obsolete too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The can_rx_alldev_list is a per-net data structure now and allocated in
can_pernet_init(). Make sure the memory is free'd in can_pernet_exit() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SocketCAN driver for Microchip CAN BUS Analyzer
(http://www.microchip.com/development-tools/)
Changes in v4:
- possible memory leak fixed in mcba_usb_write_bulk_callback
- LED support added
- failure handling in mcba_usb_probe improved
- C99 initializers for structs on stack
Changes in v3:
- improved/simplified CAN ID conversion
- functions for transmission of skb and cmd separated
- fixed/improved netif_stop_queue handling
- style/cosmetic corrections
Changes in v2:
- Termination handling reimplemented to fit new netlink API
(IFLA_CAN_TERMINATION)
- Bitrate handling reimplemented to fit new netlink API
(IFLA_CAN_BITRATE)
- CAN ID conversion refactored (changed from macro to inline functions)
- CAN DLC handling using get_can_dlc()
- Endianness handling for can_speed introduced
- Debugging removed
- Redundant error prints removed
- Style/cosmetic corrections (i.e. macro names, redefs, inits etc.)
Signed-off-by: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Added defines for TX Event FIFO Element
* Adapted ndo_start_xmit function.
For versions >= v3.1.x it uses the TX FIFO to optimize the data
throughput. It stores the echo skb at the same index as in the
M_CAN's TX FIFO. The frame's message marker is set to this index.
This message marker is received in the TX Event FIFO after
the message was successfully transmitted. It is used to echo the
correct echo skb back to the network stack.
* Added m_can_echo_tx_event function. It reads all received
message markers in the TX Event FIFO and loops back the
corresponding echo skbs.
* ISR checks for new TX Event Entry interrupt for version >= 3.1.x.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* TX/TX Event FIFO sizes are configured for version >= v3.1.x
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adapts the initialization of the M_CAN. So it can be used
with all versions >= 3.0.x.
Changes:
* Added version element to m_can_priv structure to hold M_CAN version.
* Renamed bittiming structs for version 3.0.x
* Added new bittiming structs for version >= 3.1.x
* Function alloc_m_can_dev takes 2 new arguments. The TX FIFO size and the
base address of the module.
* Chip configuration for CAN_CTRLMODE_LOOPBACK is changed: Enabled
CCCR_MON bit. In combination with TEST_LBCK it activates the internal
loopback mode. Leaving CCCR_MON '0' results in external loopback mode.
* Clocks are temporarily enabled by platform_propbe function in order to
allow read access to the Core Release register and the Control Register.
Registers are used to detect M_CAN version and optional Non-ISO Feature.
Initialization of M_CAN for version >= 3.1.x:
* TX FIFO of M_CAN is used to transmit frames. The driver does not need to
stop the tx queue after each frame sent.
* Initialization of TX Event FIFO is added.
* NON-ISO is fixed for all M_CAN versions < 3.2.x. Version 3.2.x _can_ have
the NISO (Non-ISO) bit which can switch the mode of the M_CAN to Non-ISO
mode. This bit does not have to be writeable. Therefore it is checked.
If it is writable Non-ISO support is added to the controllers supported
CAN modes.
New Functions:
* Function to check the Core Release version. The read value determines the
behaviour of the driver.
* Function to check if the NISO bit for version >= 3.2.x is implemented.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Updated register defines to newest M_CAN version (v3.2.1).
* Changed defines in the whole code.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The virtual address of the device was printed. I removed it because it
leaks internal information.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
FIFO water marks disabled because the driver doesn't handle water mark
events.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Disabled interrupt line 1. The driver didn't use it.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-PCI Express FD boards made
by PEAK-System, for computers using the PCI Express slot.
The PCAN-PCI Express FD has one or two CAN FD channels, depending
on the model. A galvanic isolation of the CAN ports protects
the electronics of the card and the respective computer against
disturbances of up to 500 Volts. The PCAN-PCI Express FD can be operated
with ambient temperatures in a range of -40 to +85 °C.
Such boards run an extented version of the CAN-FD IP running into USB
CAN-FD interfaces from PEAK-System, so this patch adds several new commands
and their corresponding data types to the PEAK CAN-FD common definitions
header file too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN-FD IP from PEAK-System runs into several kinds of PC CAN-FD
interfaces. Up to now, only the USB CAN-FD adapters were supported by
the Kernel. In order to prepare the adding of some new non-USB CAN-FD
interfaces, this patch moves - and rename - the IP definitions file
from its private (usb) sub-directory into a - newly created - CAN specific
one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
