Add support to differentiate between iMR(no external memory) and MR(with
external memory) controllers.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MegaRAID older Firmware does not support uneven span configuration for PRL11.
E.g User wants to create 34 Driver PRL11 config, it was not possible using old
firmware, since it was not supported configuration in old firmware
Old Firmware expect even number of Drives in each span and same number of
physical drives at each span. Considering above design, 17 Drives at Span-0
and 17 drives at span-1 was not possible.
Now, using this new feature Firmware and Driver both required changes. New
Firmware can allow user to create 16 Drives at span-0 and 18 Drives at
span-1. This will allow user to create 34 Drives Uneven span PRL11.
RAID map is interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives. Since legacy RAID map consider
Even Span design, there was no place to keep Uneven span information in
existing Raid map. Because of this limitation, for Uneven span VD, driver can
not use RAID map.
This patch address the changes required in Driver to support Uneven span PRL11
support.
1. Driver will find if Firmware has UnevenSpanSupport or not by reading
Controller Info.
2. If Firmware has UnvenSpan PRL11 support, then Driver will inform about its
capability of handling UnevenSpan PRL11 to the firmware.
3. Driver will update its copy of span info on each time Raid map update is
called.
4. Follow different IO path if it is Uneven Span. (For Uneven Span, Driver
uses Span Set info to find relavent fields for that particular Virtual
Disk)
More verbose prints will be available by setting "SPAN_DEBUG" to 1 at
compilation time.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This Driver will use more than 8 MSI-x support provided by Invader/Fury max
upto 128 MSI-x.
[jejb: fix checkpatch warning]
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Previously we used PCI_MSI_FLAGS to locate a register in the MSI-X
capability. This did work because the MSI and MSI-X flags happen
to be at the same offsets, but was confusing.
PCI_MSIX_FLAGS_ENABLE is already defined in include/uapi/linux/pci_regs.h,
so no need to define it again.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Adam Radford <aradford@gmail.com>
This patch updates the megaraid_sas driver version and updates
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
This allows a user to adjust the queue depth of the adapter when throttled due
to I/O timeout.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the driver version to
v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This code has never worked correctly, doesn't disable interrupts when
set as a module parameter, doesn't disable interrupts when set after
driver load time in sysfs node, etc.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the
ChangeLog.megaraid_sas file and updates the driver version.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas adds a driver workaround for
PERC5/1068 based controller FW that keeps a command from the main
kernel that the driver cannot cancel which was causing a kernel panic
in shutdown of the kdump kernel.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas fixes the function
megasas_reset_fusion() and makes the reset code check
MFI_REG_STATE.fault.resetAdapter.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas fixes megasas_probe_one() to
clear MSI-X flags in kdump when the 'reset_devices' kernel parameter
is passed in.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds MegaRAID 9265/9285 (Device id 0x5b) specific code
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch adds struct megasas_instance_template changes to
the megaraid_sas driver, and changes all code to use the new instance
entries:
irqreturn_t (*service_isr )(int irq, void *devp);
void (*tasklet)(unsigned long);
u32 (*init_adapter)(struct megasas_instance *);
u32 (*build_and_issue_cmd) (struct megasas_instance *, struct scsi_cmnd *);
void (*issue_dcmd) (struct megasas_instance *instance,
struct megasas_cmd *cmd);
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch modifies the megaraid_sas driver to select the
lowest memory bar available so the driver will work in SR-IOV VF
environments where the memory bar mapping changes.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds MSI-X support and 'msix_disable' module parameter to
the megaraid_sas driver.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch updates the GPL headers in megaraid_sas_base.c and megaraid_sas.h.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver add the input parameters support for max_sectors for megaraid
sas gen2 chip. Customer can set the max_sectors support to 1MB for
gen2 chip during the driver load.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To add the Online controller reset support, driver need to do:
a). reset the controller chips -- Xscale and Gen2 which will change
the function calls and add the reset function related to this two
chips.
b). during the reset, driver will store the pending cmds which not
returned by FW to driver's pending queue. Driver will re-issue those
pending cmds again to FW after the OCR finished.
c). In driver's timeout routine, driver will report to OS as reset.
Also driver's queue routine will block the cmds until the OCR
finished.
d). in Driver's ISR routine, if driver get the FW state as state
change, FW in Failure status and FW support online controller
reset (OCR), driver will start to do the controller reset.
e). In driver's IOCTL routine, the application cmds will wait for the
OCR to finish, then issue the cmds to FW.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver issue the get ld list to fw to get the logic drive list.
Driver will keep the logic drive list for the internal use after
driver load.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver will update the OS devices after adding and deleting the device
from FW. When driver receive add or delete AEN from FW, driver will
send the DCMD cmd to get the System PD list from FW. Then driver will
check if this device already in the OS: If add event and OS don't have
the device (but it is in the list), driver add the device to OS,
otherwise driver will not add. If remove event, driver will check the
list, if is not in the list, but OS have the device, driver will
remove the device.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a lock to the skinny firmware initialisation sequence to prevent
the two stage write being non atomic if multiple instances use it.
Add a flag to the driver shutdown sequence to prevent aen ioctls being
called after shutdown begins.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To increase the performance, megaraid sas driver added the IEEE SGE
support to support SAS2 controller.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MegaRAID SAS2 controller ioctl can't use 32 cmd for applications.
Driver need to divide different number of cmds to IO and application.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add system PDs to OS. Driver implemented the get_pd_list function to
get the system PD from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the new megaraid sas 2 controller to the driver. megaraid sas2 is
LSI next generation SAS products. driver add the interface to support
this product.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add Poll_wait mechanism to SAS-2 MegaRAID SAS Linux driver. Driver
will wakeup poll after the driver get event from MegaRAID SAS FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add the new controllers (0x78 0x79) support to the driver. Those
controllers are LSI's next generation (gen2) SAS controllers.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: parenthesise a macro]
Signed-off-by: Bo Yang <bo.yang@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update the Version and Changelog for megaraid_sas Driver
Signed-off-by: Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add the new Controller (ID: 007C) support to driver.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When Driver sent wrong frame count to firmware. As this particular
command is sent to drive, FW is seeing continuous chip resets and so
the command will timeout.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
