Support command line parameters of the form:
earlycon=<name>,io|mmio|mmio32|mmio32be,<addr>,<options>
This commit seem to be needed even after commit:
serial: 8250: Add support for big-endian MMIO accesses
c627f2ceb6
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the serial works as a bluetooth sink, due to audio realtime
requirement, the driver should have something similar with ALSA:
1. one big DMA buffer to easy the schedule jitter
2. split this big DMA buffer to multiple small periods, for each
period, we get a DMA interrupt, then push the data to userspace.
the small periods will easy the audio latency.
so ALSA generally uses a cyclic chained DMA.
but for sirfsoc, the dma hardware has the limitation: we have
only two loops in the cyclic mode, so we can only support two
small periods to switch. if we make the DMA buffer too big, we
get long latency, if we make the DMA buffer too little, we get
miss in scheduling for audio realtime.
so this patch moves to use a hrtimer to simulate the cyclic
DMA, then we can have a big buffer, and also have a timely
data push to users as the hrtimer can generate in small period
then actual HW interrupts.
with this patch, we also delete a lot of complex codes to handle
loop buffers, and RX timeout interrupt since the RX work can be
completely handled from hrtimer interrupt.
tests show using this way will make our bad audio streaming be-
come smooth.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A corner case exists in the current driver. if an app opens the console
device, and before writing to console device, and there are huge kernel
ogs to print out, system will hang on
sirfsoc_uart_console_putchar:
while (rd_regl(port, ureg->sirfsoc_tx_fifo_status) &
ufifo_st->ff_full(port->line))
cpu_relax();
as in sirfsoc_uart_startup(), the driver assigns tx_fifo_op to 0 will stop
TX FIFO, this loop will be endless.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_set_mctrl() is a void type function. Returning something
does not look nice.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS-485 configuration is also done under the spinlock
so no blocking I/O allowed.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.stop_rx/tx() are called in atomic context, we cannot use
blocking I/O. While at it correct the name of RX bit and
'*' placement in pointer declarations.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert md_proc into general async reconfiguration procedure.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of spinning under port->lock let's just sleep
inside the kthread. It should be equivalent as TX cannot
proceed when thread is blocked.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert workqueue usage to a real-time kworker. The problem
with workqueues is that we cannot set real-time priorities on
our work and asynchronous reconfiguration can be blocked by
less important tasks.
We need kthread for the interrupt anyway and because we will
now be using single kthread for all TX-related operations we
can get rid of the port mutex.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LSR_TEMT_BIT (LSR bit 6) provides us exactly the information
we need to determine if transmission is finished - FIFO level
and shift register empty. We can save ourselves reading FIFO
level explicitly if we use this bit.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without matching bus-specific strings driver will not be loaded
automatically.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users of RS-485 can request via ioctl that RTS signals should
be activated selected number of milliseconds before the actual
data transmission or delay reception certain number of milli-
seconds after the transmission is finished. In sc16is7xx,
however, RTS signalling is handled by the hardware and driver
has no way of providing this feature.
We still try to provide .delay_rts_before_send by delaying
transmission but without actual effect on the RTS line.
Note: this change will make the driver return -EINVAL when the
feature is requested (.delay_rts_after_send is set).
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi interface for sc16is7xx is added along with Kconfig flag
to enable spi or i2c, thus in a instance we can have either
spi or i2c or both, in sync to the hw.
Signed-off-by: Rama Kiran Kumar Indrakanti <indrakanti_ram@hotmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the necessary driver boilerplate to let the driver be used when
the respective ACPI table is discovered by the ACPI subsystem.
[Andre: change table name, add MODULE_DEVICE_TABLE entry and improve
commit message]
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM Server Base System Architecture[1] document describes a
generic UART which is a subset of the PL011 UART.
It lacks DMA support, baud rate control and modem status line
control, among other things.
The idea is to move the UART initialization and setup into the
firmware (which does this job today already) and let the kernel just
use the UART for sending and receiving characters.
We use the recent refactoring to build a new struct uart_ops
variable which points to some new functions avoiding access to the
missing registers. We reuse as much existing PL011 code as possible.
In contrast to the PL011 the SBSA UART does not define any AMBA or
PrimeCell relations, so we go with a pretty generic probe function
which only uses platform device functions.
A DT binding is provided with this patch, ACPI support is added in a
separate one.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBSA UART has a fixed baud rate and flow control setting, which
cannot be changed or queried by software.
Add a vendor specific property to always return fixed values when
trying to read the console options.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBSA UART should not be enabled or disabled (it is always on),
and consequently the spec lacks the UART_CR register.
Add a vendor specific property to skip disabling or enabling of the
UART. This will be used later by the SBSA UART support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid lines with more than 80 characters and to make the
pl011_int() function more readable, move the workaround out into a
separate function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register UART_MIS is actually a bitwise AND of the
UART_RIS and the UART_MISC register.
Since the SBSA UART does not include the _MIS register, use the
two separate registers to get the same behaviour. Since we are
inside the spinlock and we read the _IMSC register only once, there
should be no race issue.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the pl011_probe() function is relying on some AMBA IDs
and a device tree node to initialize the driver and a port.
Both features are not necessarily required for the driver:
- we lack AMBA IDs in the ARM SBSA generic UART and
- we lack a DT node in ACPI systems.
So lets refactor the function to ease later reuse.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_set_termios() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_shutdown() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_startup() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although we care about not unregistering the driver if there are
still ports connected during the .remove callback, we do miss this
check in the pl011_probe function. So if the current port allocation
fails, but there are other ports already registered, we will kill
those.
So factor out the port removal into a separate function and use that
in the probe function, too.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mediatek serial port driver is built-in, but serial
console is disabled in Kconfig (e.g. when the serial driver
itself is a loadable module), we get this build error:
drivers/built-in.o: In function `early_mtk8250_setup':
undefined reference to `early_serial8250_setup'
To avoid that problem, this patch encloses the early_mtk8250_setup
function in #ifdef CONFIG_SERIAL_8250_CONSOLE, the same symbol
that guards the early_serial8250_setup function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A configuration that enables earlycon but not the core console
code causes a link error:
drivers/built-in.o: In function `setup_earlycon':
drivers/tty/serial/earlycon.c:70: undefined reference to `uart_parse_earlycon'
That error can be triggered by the newly added samsung earlycon support,
which is missing a 'select' statement.
As suggested by Peter Hurley, solves the problem by moving the
'select SERIAL_EARLYCON' statement to the samsung console driver
option, as it is done by all other console drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b94ba0328d ("serial: samsung: Add support for early console")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function mctrl_gpio_init returns failure if the assignment to any
member of the gpio array results in an error pointer. So there is no
need to check for such error values in the other functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to dmaengine_slave_config() fails, then the DMA buffer will
not be freed/unmapped. Fix this by moving the code that stores the
address of the buffer in the tegra_uart_port structure to before the
call to dmaengine_slave_config().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it seems this is a more typical behaviour from reviewing other console
drivers.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add overrun error's flag mark and parity's counter, we can show the
statistic from procfs node.
BTW, let the indentation of stick bits configuration look better.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In special condition, when cpu schedule into rx_tmo_process_tl or
rx_dma_complete_tl and all the receive dma tasks have done, it will
go into endless loop because no dma task cookie status be changed.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From HW spec, when rxfifo's data is less than AFC_RX_THD(RX threshhold), RTS
signal is active. otherwise, RTS signal is inactive.
Crrently the RX threshhold is set as zero, so RTS has no chance to be
active. This patch replaces the default 0 by a positive number.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
differentiate difference port types by re-defining the status MARCO
or putting HW differences into private data of the related ports.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...
Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.
Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 734745caeb serial/amba-pl011:
(Activate TX IRQ passively) introduces a race which causes the driver
sometimes to attempt to write a character to the TX FIFO when the FIFO
is already full.
The PL011 does not guarantee its behaviour when the FIFO is overfilled.
In practice, this can cause duplicate and/or dropped characters to be
output on the wire. The problem is common enough to be readily
observable on the ARM Juno platform when the PL011 UART is used as
the console and DMA is not in use.
This patch fixes this problem by always polling for space before each
character is written to the FIFO.
This will be amended to a less brute-force approach in a later commit,
but this patch should help ensure correct behaviour for now.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 02730d3c05
(Merge 4.1-rc4 into tty-next), git mismerged some lines,
reintroducing a reference to the removed field
uart_amba_port.tx_irq_seen. This causes a build failure.
This patch removes the mismerged lines, restoring the code to what
was in tty-next (which was the intention).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is no longer used now that mach-msm has been removed.
Delete it.
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function tegra_uart_dma_channel_allocate() does not check that
dma_map_single() mapped the DMA buffer correctly. Add a check for this
and appropriate error handling.
Furthermore, if dmaengine_slave_config() (called by
tegra_uart_dma_channel_allocate()) fails, then memory allocated/mapped
is not freed/unmapped. Therefore, call tegra_uart_dma_channel_free()
instead of just dma_release_channel() if dmaengine_slave_config() fails.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues in the shutdown path of the UARTs which are:
1. The function tegra_uart_shutdown() calls tegra_uart_flush_buffer()
to stop DMA TX transfers. However, tegra_uart_flush_buffer() is
called after the DMA channels have already been freed and so actually
does nothing.
2. The function that frees the DMA channels
(tegra_uart_dma_channel_free()), unmaps the dma buffer before
freeing the DMA channel and does not ensure the DMA has been
stopped.
Resolve this by fixing the code in tegra_uart_dma_channel_free() to
ensure the DMA is stopped, free the DMA channel and then unmap the DMA
buffer. Finally, remove the unnecessary call to tegra_uart_flush_buffer().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA cookie for the RX channel is being used by the TX channel.
Therefore, fix driver to use the correct DMA cookie for the TX channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() takes an argument "size" which is
of type size_t. This is an unsigned type. Update the count,
rx_bytes_requested and tx_bytes_requested in the tegra serial driver to
be unsigned integers so that an unsigned type is passed to
tty_insert_flip_string().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra serial driver has two paths through which receive data is
copied up to the tty layer. These are:
1. DMA completion callback
2. UART RX interrupt
A UART RX interrupt occurs for either RX_TIMEOUT (data has been sitting
in the Rx FIFO for more than 4 character times without being read
because there is not enough data to reach the trigger level), End of
Receive Data event (receiver detects that data stops coming in for more
than 4 character times) or a receive error.
In the RX interrupt path, the following happens ...
- All RX DMA transfers are stopped
- Any data in the DMA buffer and RX FIFO are copied up to the tty layer.
- DMA is restarted/primed for the RX path
In the DMA completion callback, the DMA buffer is copied up to the tty
layer but there is no check to see if the RX interrupt could have
occurred between the DMA interrupt firing the the DMA callback running.
Hence, if a RX interrupt was to occur shortly after the DMA completion
interrupt, it is possible that the RX interrupt path has already copied
the DMA buffer before the DMA callback has been called. Therefore, when
the DMA callback is called, if the DMA is already in-progress, then this
indicates that the UART RX interrupt has already occurred and there is
nothing to do in the DMA callback. This race condition can cause
duplicated data to be received.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Moved async_tx_ack() call to after check to see
if DMA has completed because if the DMA is in progress we do not need
to ACK yet. Changed the print from dev_info to dev_debug. Updated
changelog to add more commentary on the race condition based upon
feedback from author.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is only necessary to read data from the dma buffer when the count
value is non-zero and hence, tegra_uart_copy_rx_to_tty() so only be
called when this is the case.
Although, this was being tested for in two places, there is a third
place where this was not tested. However, instead of adding another
if-statement prior to calling tegra_uart_copy_rx_to_tty(), move the test
inside the function.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Re-worked patch to move the check for the count
value inside the function tegra_uart_copy_rx_to_tty(). Updated
changelog with more commentary.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 3 UART clock periods after enabling
the TX fifo, otherwise data could be lost.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 32 UART clock periods for the flush
to propagate otherwise TX data could be post. Add a helper function
to wait for N UART clock periods and update delay following FIFO
flush to be 32 UART clock cycles.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port.type has already been set by of_platform_serial_setup()
called from a few lines above.
Setting it to the same value is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port.fifosize member has already been copied at 8 lines above.
Maybe the compiler optimization can clean it away, but just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early console functions are only used during the early boot stage.
This change just saves a small amount of memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nr_uarts was set to 0 (via config or 8250_core.nr_uarts), we crash
early on x86 because serial8250_isa_init_ports dereferences base_ops
which remains NULL. In fact, there is nothing to do for all the callers
of serial8250_isa_init_ports if there are no uarts.
Based on suggestions by Peter Hurley.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Staticize symbols not exported and not used outside of file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code it refers to was removed in commit b545e4f406 ("serial:
sh-sci: Compute overrun_bit without using baud rate algo").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
error_mask is the union of all error indicating bits in the SCxSR
register, while overrun_mask may apply to a different register (SCLSR),
depending on the SCI variant.
Hence overrun_mask should only be ORed into error_mask if it applies to
the SCxSR register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various SCI implementations use 3 different methods to signal
overrun errors:
- Bit SCI_ORER in register SCxSR on SCI,
- Bit SCIFA_ORER in register SCxSR on SCIFA and SCIFB, and SCIF on
SH7705/SH7720/SH7721,
- Bit SCLSR_ORER in (optional!) register SCLSR on (H)SCIF.
However:
1. sci_handle_fifo_overrun()
a. handles (H)SCIF and SCIFA/SCIFB only,
b. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
2. sci_mpxed_interrupt()
a. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
b. ignores that not all SCIFs have the SCLSR register, causing
"Invalid register access" WARN()ings.
To fix the above:
1. Determine and store the correct register enum during
initialization,
2. Replace the duplicated buggy switch statements by using the stored
register enum,
3. Add the missing existence check to sci_mpxed_interrupt().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing overrun bit definition for (H)SCIF.
Replace overrun_bit by overrun_mask, so we can use the existing
defines instead of hardcoded values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing overrun error bit in SCxSR on SCIFA/SCIFB and SCIF on
SH7705/SH7720/SH7721.
Document what the corresponding bit(s) on plain SCIF are used for.
Sort the components of SCIF_DEFAULT_ERROR_MASK by reverse definition
order.
Replace the hardcoded values in the SCxSR_*_CLEAR macros by proper
defines. Use bit masks (negations of sets of bits) to make it more
obvious which bits are being cleared.
Assembler output (on sh) was compared before and after this commit:
- For the first branch of the big "#if defined(...) || ..." construct,
the code has changed slightly, as 32-bit bitmasks can be loaded in a
single instruction, unlike the old large 16-bit constants (the SCxSR
register is 16 bit, so we don't care about the top 16 bits),
- For the second branch, the generated code is identical.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the register definitions for the Serial Port Control and Data
Registers on SCIFA/SCIFB, which are needed for RTS/CTS pin control.
Extracted from patches by Magnus Damm <damm+renesas@opensource.se>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing register bit definitions to set the RTS pin and read the
CTS pin on (H)SCIF.
Extracted from patches by Magnus Damm <damm+renesas@opensource.se>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move private register definitions and enums from the public
<linux/serial_sci.h> header file to the driver private "sh-sci.h" header
file.
The common Serial Control Register definitions are left in the public
header file, as they're needed to fill in plat_sci_port.scscr on legacy
systems not using DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Pat Gefre <pfg@sgi.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Pat Gefre <pfg@sgi.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Mikael Starvik <starvik@axis.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In SiRF platform, there are different fifo size of uart and usp,
with the fifosize configuration changes in different chips, we
can not use port line to decide how to check FIFO full,empty and
level.
There is a direct mapping between FIFO HW register layout with
fifo size, so move to use fifosize as the input to check fifo
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In different platform of SiRF SoCs, there is no same uart and usp-uart
numbers, it is not convenient to use hard-coded ports array and port
lines.
here we drop the hard-coded ports table , and drop "cell-index". then
move to use alias id to get line.
for example:
aliases {
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
serial6 = &uart6;
serial9 = &usp2;
};
at the same, enlarge the max port number according to the chip with the most
UART.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 8250 MTK UART driver to support earlycon device tree.
Earlycon take effect by
add "earlycon" in kernel boot argument
add "linux,sdtout-path" property in device tree file
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2ee6dfa0e.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is pm_qos_add_request() being executed on serial_omap_probe(),
which stores "&up->pm_qos_request" from omap-serial driver to
"pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If
serial_omap_probe() fails after pm_qos_add_request() (e.g. on
uart_add_one_port() call), pm_qos_array still keeping pm_qos_request
struct from omap-serial driver, which is not valid anymore (since driver
failed). This leads further to kernel crash on pm_qos_update_target(),
executing from some completely different driver.
We were observing this while trying to run audio playback while having
one of omap-serial driver instances failed on uart_add_one_port() call:
Unable to handle kernel paging request at virtual address fffffffc
Backtrace:
(plist_add) from (pm_qos_update_target)
(pm_qos_update_target) from (pm_qos_add_request)
(pm_qos_add_request) from (snd_pcm_hw_params)
(snd_pcm_hw_params) from (snd_pcm_common_ioctl1)
(snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1)
(snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl)
(snd_pcm_playback_ioctl) from (do_vfs_ioctl)
(do_vfs_ioctl) from (SyS_ioctl)
(SyS_ioctl) from (ret_fast_syscall)
This patch adds pm_qos_remove_request() on fail path in
serial_omap_probe() in order to fix this issue. While at it, free the
wakeup settings on fail path as well, just like it's done in
serial_omap_remove().
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Log warnings meant to help diagnose problems setting up earlycon
are reporting false positives for 'console='. Revert to the
previous behavior which reported nothing.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk 8250 needs two clocks, one for providing the baudrate and
one that needs to be enabled for register accesses. The latter has
not been supported, this patch adds support for it. It is optional
for now since not all SoCs provide a bus clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime callbacks already enable and disable the device.
Use them in probe() and remove() instead of duplicating the
code. This allows us to concentrate more code for enabling/disabling
the UART in a single place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a struct device * is present clk_get should be used rather
than of_clk_get. Use the devm variant of this function to be able to
drop the clk_put in the error and remove pathes. While at it fix
a wrong error message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver has probed successfully the clk pointer is always valid,
so no need to test for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function meson_uart_release_port() inappropriately try to
iounmap() a resource managed by devm_ioremap_nocache().
The function meson_uart_release_port() maybe called by uart_ioctl()
that means meson_uart_release_port() is not called from within a
probe or remove function, for safety, I convert iounmap() to
devm_iounmap().
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_running flag should show if DMA is currently active. However
there is a window between when the flag is set/cleared and when
the DMA is started/stopped. Because the flag is queried from both
hard and soft irq contexts, the driver can make incorrect
decisions and do things like start a DMA transfer using a buffer
that is already setup to be used for a DMA transfer.
This patch adds a spinlock to synchronize the rx_running flag and
close the above mentioned window.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `ifx_spi_free_device':
ifx6x60.c:(.text+0x96d9a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ifx_spi_spi_probe':
ifx6x60.c:(.text+0x978a2): undefined reference to `dma_alloc_coherent'
While DMA is optional in this driver, and is used only if
ifx_modem_platform_data.use_dma is set, there are currently no in-tree
users of ifx_modem_platform_data (and thus of this driver), so just make
it depend on HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to cast the last parameter of {request,free}_irq() to
"void *", as any pointer type is accepted.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting spi_driver pointers to "void *" when calling
spi_{,un}register_driver() bypasses all type checking.
Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 52bec4ed4e("serial: sirf: add a new uart type
support").
we misunderstood the clock dependency in atlas7. Actually involved
several clocks are in a tree structure. we still only need to take
the leaf clock node for BT uarts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove CONFIG_SERIAL_DETECT_IRQ and CONFIG_SERIAL_MANY_PORTS, and
substitute all references to the proper 8250 Kconfig options. Now, the
actual Kconfig dependencies are not hidden when reading the code and
static analyzers are less confused.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_ prefix is reserved for Kconfig options in Make and CPP
syntax; static analysis tools rely on this convention. This patch
enforces this behavior for SERIAL_BFIN_{HARD_}CTSRTS.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix reference on PPC_MPC52xx in C comment after #endif.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file local CPP identifier is not referenced anywhere else, so we
can safely remove it.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the changed flag of IRQ status in interruption
instead of handling it in tasklet due to the tasklet
may be scheduled more than once in one interruption.
Otherwise, the changed status may be processed more
than once which will lead to unexpected result. And
seriously, kernel will crash.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'CONFIG_' prefix is reserved for Kconfig options in Make and CPP
syntax only. Remove this prefix from the self-defined CPP identifier to
apply to this convention and make static analysis tools happy.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_SERIAL_PROC_ENTRY is not defined in Kconfig. The affected #ifdef
block has not been compiled for years, and the embedded macro, PROCSTAT,
ended up as a NOOP. Hence, remove the block and all calls to PROCSTAT.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_RS485_{ON_PORT_G, LTC1387} are not defined in Kconfig. The
affected #ifdef block have not been compiled for years, so remove them
entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ETRAX_EXTERN_PB6CLK_ENABLED is not defined in Kconfig. The affected
#ifdef block has not been compiled for years, so remove it entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig option ARCH_SH7372 has been removed by commit 59b89af1d5
("ARM: shmobile: sh7372: Remove Legacy C SoC code"). This patch removes
the last reference on this Kconfig option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value from imx_setup_ufcr() is always 0 and its value is never
checked, so better to remove the return value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously Soft Reset (clear of SRST bit in UCR2 register)
of UART in startup is not protected by lock, which may have race
with console_write, as console_write may occur at anytime even
when UART port is shutdown.
To avoid this race, protect Soft reset of UART port with spin_lock.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 734745c serial/amba-pl011: Activate TX IRQ passively
adds some complexity and overhead in the form of a softirq
mechanism for transmitting in the absence of interrupts.
This patch simplifies the code flow to reduce the reliance on
subtle behaviour and avoid fragility under future maintenance.
To this end, the TX softirq mechanism is removed and instead
pl011_start_tx() will now simply stuff the FIFO until full
(guaranteeing future TX IRQs), or until there are no more chars
to write (in which case we don't care whether an IRQ happens).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2ee6dfa0e.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
If the device node has a "big-endian" property and 32-bit registers, tell
the serial driver to use UPIO_MEM32BE instead of UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add cases for UPIO_MEM32BE wherever there are currently cases handling
UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
Hardware is capable of inverting RTS signal when working
in RS-485 mode. Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).
It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.
We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the expected behavior of kernel command lines of the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
and
earlycon=uart[8250],io|mmio|mmio32,<addr>[,options]
earlycon=uart[8250],<addr>[,options]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a849 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit ba019a3e2a ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2a ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tangier contains 4 HSUART ports as found on Intel Edison board which are
8250 compatible. The patch adds necessary bits to the driver.
Note that the HSU port0 is currently unavailable and thus not supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12 48000000 64000000 4000000(1)
49 50 14 49000000 56000000 3500000(1)
4 5 16 40000000 40000000 2500000(1)
16 25 16 32000000 32000000 500000(4),1000000(2),2000000(1)
24 25 16 48000000 48000000 1500000(2),3000000(1)
2304 3125 16 36864000 36864000 576000(4),1152000(2)
8192 15625 16 26214400 26214400 50(32768),200(8192)
9216 15625 16 29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),1843200(1)
12288 15625 16 39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16 28835840 28835840 110(16384)
274432 390625 16 3512729635127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
4 5 16 80000000 80000000 2500000(2)
14 25 16 56000000 56000000 3500000(1)
16 25 16 64000000 64000000 500000(8),1000000(4),2000000(2),
4000000(1)
24 25 16 96000000 96000000 1500000(4),3000000(2)
2180 3103 16 70254592 70254592 134(32768)
2304 3125 16 73728000 73728000 576000(8),1152000(4)
8192 15625 16 52428800 52428800 50(65536),200(16384)
9216 15625 16 58982400 58982400 1800(2048),57600(64),115200(32),
230400(16),460800(8),921600(4),1843200(2)
12288 15625 16 78643200 78643200 75(65536),150(32768),300(16384),
600(8192),1200(4096),2400(2048),
4800(1024),9600(512),19200(256),38400(128)
9893 17154 16 57671680 57671680 110(32768)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"brd->nasync" amd "brd->maxports" are the same. They hold the number of
filled out channels in the brd->channels[] array. These tests should
be ">=" instead of ">" so that we don't read one element past the end.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the 8250 driver reserve exactly the mmio region specified
in the devicetree. This prevents conflicts between UPIO_AU type
UARTs and other devices mapped closer than the default size of
0x1000 (or 0x100 for RT2880).
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a mapsize field to struct uart_port to be used in
conjunction with mapbase. If set, it overrides whatever value
serial8250_port_size() would otherwise report.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although clk_disable_unprepare() is called both on .remove()
and in .probe() error path, the clock is never actually enabled.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EFCR register contains RS-485 configuration which should not
be changed by shutdown. Instead of doing a write only update
the appropriate bits.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not explicitly removed on the error path
the device will not get properly unregistered leaving
/dev/ttySC* nodes in the filesystem.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
