Used by the regulator driver.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It's relying on non-exported symbols.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is supposed to be umode_t. It causes a GCC warning:
drivers/mfd/lm3533-core.c:440:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mfd/lm3533-core.c:440:2: warning: (near initialization for ‘lm3533_attribute_group.is_visible’) [enabled by default]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The name of the tunnelcreek watchdog device is not tunnelcreek_wdt but
ie6xx_wdt.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use SI-units (uA) for max-current interface (5000 - 29800 uA).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The max-current attributes of the subdrivers have been dropped so
remove the no longer used lm3533_ctrlbank_get_max_current function.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove boost-frequency and ovp attributes, which can be set through
platform data, from sysfs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add boost-frequency and over-voltage-protection settings to platform
data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Save a useful amount of code by removing the custom cache implementation
for wm8400 and using the regmap cache. Also simplify things by not
separately reseting the CODEC registers, this is a sufficiently infrequent
operation that we can simply invalidate the entire cache when this happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65910_parse_dt() prototype for !CONFIG_OF was not correct, leading to:
drivers/mfd/tps65910.c: In function ‘tps65910_i2c_probe’:
drivers/mfd/tps65910.c:218:3: error: too many arguments to function ‘tps65910_parse_dt’
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As gpio support for tps65910 is on gpio driver, registering
gpio support as the mfd sub devices instead of calling gpio_init()
from the core probe.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert memory allocation and regmap initialization to
use devm_* functions.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During regmap initialization, we do not provide the default value and
hence in place of caching register during regmap_init(), cache it
when actually we need it i.e. after reading of that register.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl-regulator has a collection of feature flags, some defined
in twl-core.c and one defined in i2c/twl.h.
This is confusing for anyone adding a new feature flag.
So collect them together and place them in twl.h immediately
after the structure in which they are initially set.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add device tree based initialization support for TI's tps65910 pmic.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change removes the read/write callback functions in favor of common
regmap accessors inside the header file. This change also makes use of
regmap_read/write for single register access which maps better onto what this
driver actually needs.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Hierarchical interrupt is supported since ab8500 V2.
However, it is not implemented in the ab8500-core driver.
With the current implementation, when an ab9540 interrupt
occurs, 17 Latch registers are read through i2c. With
hierarchical interrupt implementation, there are only 4 i2c
accesses.
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Reviewed-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6040 has three power supply source:
VBAT needs to be connected to VBAT, VIO, and V2V1.
Add regulator support for the VIO, V2V1 supplies.
Initially handle the two supply together with bulk commands.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the interrupts that come through this line should trigger
wakeups:
power button
RTC alarm
power available
usb plug/unplug
so mark the interrupt as a wakeup interrupt.
This is particularly important for when the interrupt arrives during
the late suspend phase. Without this setting it will be ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Return proper error instead of 0 if regmap_init_i2c fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch converts the iTCO_wdt driver to use the multi-function device
driver model. It uses resources discovered by the lpc_ich driver, so that
it no longer does its own PCI scanning.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for National Semiconductor / TI LM3533 lighting power chips.
This is the core driver which provides register access over I2C and
registers the ambient-light-sensor, LED and backlight sub-drivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This applies a supply alias for the db8500's fifth Nomadik i2c port.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch will enable probing to occur during a Device Tree enabled
boot. The IRQ base is expected to be located in and will be fetched
from the DT itself. We also prevent any of the db8500 regulators
from being registered here, as they will be enabled via DT instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pass the probe function as part of the platform_driver struct and
register using the more common platform_driver_register call. In
subsequent patches we'll also add DT support into the struct.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver calls of_match_node() with the arguments swapped.
Signed-off-by: Olof Johansson <olof@lixom.net>
Tested-by: Ying-Chun Liu <paul.liu@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the Intel Centerton processor DeviceID for the
Integrated Legacy Block (ILB).
The ILB provides GPIO, SMBus, and Watchdog functionality.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This also introduces <asm/sta2x11.h> to export a function that is in
the base sta2x11 support patches. The header will increase with other
prototypes and constants over time.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Read CUST_ID from the device and log it for diagnostics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver still uses a custom cache implementation but the underlying
physical I/O is now done using the regmap API, saving some code and
avoiding allocating enormous scratch arrays on the stack.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The removal of mach/io.h from most ARM platforms also set the range of
valid IO ports to be empty for most platforms when previously any 32
bit integer had been valid. This makes it impossible to add IO resources
as the added range is smaller than that of the root resource for IO ports.
Since we're not really using IO memory at all fix this by defining our
own root resource outside the normal tree and make that the parent of
all IO resources. This also ensures we won't conflict with read IO ports
if we ever run on a platform which happens to use them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A warning was being generated by the reference from tps65910_i2c_probe()
to tps65910_sleepinit() since the latter was annotated as __init but the
former was unannotated. Since these functions can only be called during
device init make them both __devinit, and while we're at it also annotate
tps65910_i2c_remove() __devexit for symmetry.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The legacy suspend operations have been deprecated and printing warnings
on boot for over a year now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_PM also covers runtime only PM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes it possible to disable battery management
via a module boot parameter. When 'ab8500-core.no_bm=1' then
ab8500_btemp, ab8500_chargalg, ab8500_charger and ab8500_fg will
not be probed. This boot parameter is used for scripted testing
of the system.
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If we are in the middle of an I2C transfer we need to deny suspend
of the AB8500 core. Implement an atomic reference counter for the
I2C operations to make sure we don't do this.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that the AB interrupt is only handled at a time when
all core drivers are resumed. Ensure that the AB interrupt
is marked as a wakeup interrupt.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB8505 and AB9540 has extended support for micro USB
resistance detection, used for detecting chargers. Let's
register resources for this resource. Let's also split off the
separate codec device for AB9540.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adds support for mc13xxx family ICs connected via i2c.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Acked-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All spi specific code is moved into a new module. The mc13xxx struct
moves to a new local include file by necessity.
A new config choice selects the SPI bus type support and by default is
value of SPI_MASTER to remain compatible with existing configs.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
