This patch adds clk_prepare/clk_unprepare calls to the serial/pxa
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bugzilla 40012: PIO_UNIMAP bug: error updating Unicode-to-font map
https://bugzilla.kernel.org/show_bug.cgi?id=40012
The unicode font map for the virtual console is a 32x32x64 table which
allocates rows dynamically as entries are added. The unicode value
increases sequentially and should count all entries even in empty
rows. The defect is when copying the unicode font map in con_set_unimap(),
the unicode value is not incremented properly. The wrong unicode value
is entered in the new font map.
Signed-off-by: Liz Clark <liz.clark@hp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanho Min reported that when the boot loader transfers
control to the kernel, there may be pending interrupts
causing the UART to lock up in an eternal loop trying to
pick tokens from the FIFO (since the RX interrupt flag
indicates there are tokens) while in practice there are
no tokens - in fact there is only a pending IRQ flag.
This patch address the issue with a combination of two
patches suggested by Russell King that clears and mask
all interrupts at probe() and clears any pending error
and RX interrupts at port startup time.
We suspect the spurious interrupts are a side-effect of
switching the UART from FIFO to non-FIFO mode.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Reported-by: Chanho Min <chanho0207@gmail.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jong-Sung Kim <neidhard.kim@lge.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kernel reboot, tty circular buffer is reset before last TX DMA interrupt is called,
while the buffer tail is updated in TX DMA interrupt handler. So, don't update the buffer
tail if it is reset.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We forgot to set the "key_map" variable here, so it's still NULL. This
was introduced recently in 079c9534a9 "vt:tackle kbd_table".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes:
WARNING: drivers/tty/serial/built-in.o(.data+0x30): Section mismatch in reference from the variable vt8500_platform_driver to the function .init.text:vt8500_serial_probe()
The variable vt8500_platform_driver references
the function __init vt8500_serial_probe()
And mark the remove pointer while we are here.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two callers to serial_out_sync() have a struct port right
there in scope, but then pass in a struct 8250_port which then
is locally resolved back to a struct port.
Delete the needless back and forth and just pass in the struct
port directly. Rename the function to have "_port" in its
name, so the name <--> args relationship is consistent with the
other serial_in/out vs serial_port_in/out function classes.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_in and serial_out helpers are expecting to operate
on an 8250_port struct. These in turn go after the contained
normal port struct which actually has the actual in/out accessors.
But what is happening in some cases, is that a function is passed
in a port struct, and it runs container_of to get the 8250_port
struct, and then it uses serial_in/out helpers on that. But when
you do, it goes full circle, since it jumps back inside the 8250_port
to find the contained port struct (which we already knew!).
So, if we are operating in a scope where we know the struct port,
then use the serial_port_in/out helpers and avoid the bouncing
around. If we don't have the struct port handy, and it isn't
worth making a local for it, then just leave things as-is which
uses the serial_in/out helpers that will resolve the 8250_port
onto the struct port.
Mostly, gcc figures this out on its own -- so this doesn't bring to
the table any revolutionary runtime delta. However, it is somewhat
misleading to always hammer away on 8250 structs, when the actual
underlying property isn't at all 8250 specific -- and this change
makes that clear.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking at the existing serial drivers (esp. the 8250 derived
variants) we see a common trend. They create a hardware specific
port struct, which in turn contains a generic serial_port struct.
The other trend, is that they all create some sort of shortcut
to go through the hardware specific struct, to the serial_port
struct, which has the basic in/out operations within. Looking
for the serial_in and serial_out in several drivers shows this.
Rather than let this continue, lets create a generic set of
similar helper wrappers that can be used on a struct port, so
we can eliminate bouncing out through hardware specific struct
pointers just to come back into struct port where possible.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_8250_port struct contains within a serial_port struct
and many times one or the other, or both are in scope within
functions via a passed in arg, or via container_of.
However there are a lot of cases where we have access directly
to the port pointer, but yet go through the parent 8250_port
structure instead to get it. These should just use the port
struct directly.
Similarly there are cases where it makes sense (from a code
cleanliness point of view) to declare a local for the port
struct, so we aren't going through the parent 8250_port struct
repeatedly to get to it.
We get a small reduction in text size, but it appears that
gcc was smart enough to internally be doing most of this
already, so the readability improvement is the larger gain.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These might have worked some magic with an ancient gcc back in
1992, but "objdump --disassemble" on gcc 4.6 on x86-64 shows
identical output before and after this commit. Send the casts
and their hysterical rasins to the bitbucket.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently 8250.c has serial_in and serial_out as shortcuts
to doing the port I/O. They are implemented as macros a
ways down in the file. This isn't by accident, but is
implicitly required, so cpp doesn't mangle other instances
of the common string "serial_in", as it exists as a field
in the port struct itself.
The above mangling avoidance violates the principle of least
surprise, and it also prevents the shortcuts from being
relocated up to the top of file, or into 8250.h -- either
being a better location than the current one.
Move them to 8250.h so other 8250-like drivers can also use
the shortcuts, and in the process, make the conflicting
names go away by using static inlines instead of macros.
The object file size remains unchanged with this modification.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the last traces of pausing I/O that we had back some
twenty years ago. Probably was only required for 8MHz ISA
cards running "on the edge" at 12MHz. Anyway it hasn't been
in use for years, so lets just bury it for good.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than hardcode 9600, use the existing default_baud parameter (which
also defaults to 9600).
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For cases where boards with non-default clocks are not yet added to the kernel
or when the clock varies across hardware revisions, it is useful to be
able to specify the UART clock on the kernel command line.
Add the user_uartclk parameter and prefer it, if set, to the default and
board specific UART clock settings. Specify user_uartclock on the command-line
with "pch_uart.user_uartclk=48000000".
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Fish River Island II (FRI2) UART clock following the CM-iTC
quirk handling mechanism. Depending on the firmware installed on the device, the
FRI2 uses a 48MHz or a 64MHz UART clock. This is detected with DMI strings.
Add similar UART clock quirk handling to the pch_console_setup() function to
enable kernel messages on boards with non-standard UART clocks.
Per Alan's suggestion, abstract out UART clock selection into
pch_uart_get_uartclk() to avoid code duplication.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The term "base baud" refers to the fastest baud rate the device can communicate
at. This is clock/16. pch_uart is using base_baud as the clock itself. Rename
the variables to be semantically correct.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In addition to the /32 prescaler, the MPC5200B supports a second
baudrate prescaler /4 to reach higher baudrates.
The current calculation (introduced with commit 0d1f22e4) in the kernel
preferes this low prescaler as often as possible, but with some
imprecise counterparts the communication on low baudrates fails.
According a support-mail from freescale the low prescaler (/4) allows
just 1% tolerance in bittiming in contrast to 4% of the high prescaler
(/32). The prescaler not only affects the baudrate-calculation, but
also the sampling of the bits on the wire.
With this patch, we use the slightly less precise, but higher tolerant
prescaler calculation on low baudrates up to (and including) 115200 baud
and the more precise calculation above.
Tested on a custom MPC5200B board with "fsl,mpc5200b-psc-uart".
Calculation Examples with prescaler (PS) 4 and 32 and divisor (DIV) on
various baudrates. Real stands for the real baudrate generated and Diff
for the differences between:
50 Baud PS 32 DIV 0xa122 Real 50 Diff 0.00%
75 Baud PS 32 DIV 0x6b6c Real 75 Diff 0.00%
110 Baud PS 32 DIV 0x493e Real 110 Diff 0.00%
134 Baud PS 32 DIV 0x3c20 Real 133 Diff 0.75%
150 Baud PS 32 DIV 0x35b6 Real 150 Diff 0.00%
200 Baud PS 32 DIV 0x2849 Real 199 Diff 0.50%
300 Baud PS 4 DIV 0xd6d8 Real 300 Diff 0.00%
PS 32 DIV 0x1adb Real 300 Diff 0.00%
600 Baud PS 4 DIV 0x6b6c Real 600 Diff 0.00%
PS 32 DIV 0x0d6e Real 599 Diff 0.17%
1200 Baud PS 4 DIV 0x35b6 Real 1200 Diff 0.00%
PS 32 DIV 0x06b7 Real 1199 Diff 0.08%
1800 Baud PS 4 DIV 0x23cf Real 1799 Diff 0.06%
PS 32 DIV 0x047a Real 1799 Diff 0.06%
2400 Baud PS 4 DIV 0x1adb Real 2400 Diff 0.00%
PS 32 DIV 0x035b Real 2401 Diff - 0.04%
4800 Baud PS 4 DIV 0x0d6e Real 4799 Diff 0.02%
PS 32 DIV 0x01ae Real 4796 Diff 0.08%
9600 Baud PS 4 DIV 0x06b7 Real 9598 Diff 0.02%
PS 32 DIV 0x00d7 Real 9593 Diff 0.07%
19200 Baud PS 4 DIV 0x035b Real 19208 Diff - 0.04%
PS 32 DIV 0x006b Real 19275 Diff - 0.39%
38400 Baud PS 4 DIV 0x01ae Real 38372 Diff 0.07%
PS 32 DIV 0x0036 Real 38194 Diff 0.54%
57600 Baud PS 4 DIV 0x011e Real 57692 Diff - 0.16%
PS 32 DIV 0x0024 Real 57291 Diff 0.54%
76800 Baud PS 4 DIV 0x00d7 Real 76744 Diff 0.07%
PS 32 DIV 0x001b Real 76388 Diff 0.54%
115200 Baud PS 4 DIV 0x008f Real 115384 Diff - 0.16%
PS 32 DIV 0x0012 Real 114583 Diff 0.54%
153600 Baud PS 4 DIV 0x006b Real 154205 Diff - 0.39%
PS 32 DIV 0x000d Real 158653 Diff - 3.29%
230400 Baud PS 4 DIV 0x0048 Real 229166 Diff 0.54%
PS 32 DIV 0x0009 Real 229166 Diff 0.54%
307200 Baud PS 4 DIV 0x0036 Real 305555 Diff 0.54%
PS 32 DIV 0x0007 Real 294642 Diff 4.09%
460800 Baud PS 4 DIV 0x0024 Real 458333 Diff 0.54%
PS 32 DIV 0x0005 Real 412500 Diff 10.48%
500000 Baud PS 4 DIV 0x0021 Real 500000 Diff 0.00%
PS 32 DIV 0x0004 Real 515625 Diff - 3.13%
576000 Baud PS 4 DIV 0x001d Real 568965 Diff 1.22%
PS 32 DIV 0x0004 Real 515625 Diff 10.48%
614400 Baud PS 4 DIV 0x001b Real 611111 Diff 0.54%
PS 32 DIV 0x0003 Real 687500 Diff -11.90%
921600 Baud PS 4 DIV 0x0012 Real 916666 Diff 0.54%
PS 32 DIV 0x0002 Real 1031250 Diff -11.90%
1000000 Baud PS 4 DIV 0x0011 Real 970588 Diff 2.94%
PS 32 DIV 0x0002 Real 1031250 Diff - 3.13%
1152000 Baud PS 4 DIV 0x000e Real 1178571 Diff - 2.31%
PS 32 DIV 0x0002 Real 1031250 Diff 10.48%
1500000 Baud PS 4 DIV 0x000b Real 1500000 Diff 0.00%
PS 32 DIV 0x0001 Real 2062500 Diff -37.50%
2000000 Baud PS 4 DIV 0x0008 Real 2062500 Diff - 3.13%
PS 32 DIV 0x0001 Real 2062500 Diff - 3.13%
2500000 Baud PS 4 DIV 0x0007 Real 2357142 Diff 5.71%
PS 32 DIV 0x0001 Real 2062500 Diff 17.50%
3000000 Baud PS 4 DIV 0x0006 Real 2750000 Diff 8.33%
PS 32 DIV 0x0001 Real 2062500 Diff 31.25%
3500000 Baud PS 4 DIV 0x0005 Real 3300000 Diff 5.71%
PS 32 DIV 0x0001 Real 2062500 Diff 41.07%
4000000 Baud PS 4 DIV 0x0004 Real 4125000 Diff - 3.13%
PS 32 DIV 0x0001 Real 2062500 Diff 48.44%
Signed-off-by: Frank Benkert <frank.benkert@avat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is supposed to be doing a shift before the comparison instead of
just doing a bitwise AND directly. The current code means the start()
just returns without doing anything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let us port the code to use tty_port. We now use open_count and tty
from there. This allows us also to use tty_port_tty_set with tty
refcounting instead of hand-written locking and logic.
Note that tty and open_count are no longer protected by cs->lock. It is
protected by tty_port->lock. But since all the places where they were
used are now switched to the helpers, we are fine.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Cc: <gigaset307x-common@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Close the window in open where driver_data is reset to NULL on each
open. It could cause other processes to get invalid retval from the
tty->ops operations because of the checks all over the code.
With this change we may do other cleanups. Now, the only valid check
for tty->driver_data != NULL is in close. This can happen only if open
fails at gigaset_get_cs_by_tty or try_module_get. The rest of checks
in various tty->ops->* are invalid as driver_data cannot be NULL
there. The same holds for cs->open_count. So remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: gigaset307x-common@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of digging a tty out of the tty_driver struct, which is not
defined to work, use tty_port properly. This includes proper tty
refcounting even though there is no possible race currently. But we
will need tty_port for tty buffers in the future anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer is initialized too late. tty->open may fire an invalid
timer. So initialize the timer earlier using DEFINE_TIMER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty->count test in the timer was racy. Let's remove the test and
properly delete the timer and wait for the body to finish using _sync
version of del_timer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, no need to duplicate the code. Let's use the helper.
Amiserial changes are only free of compilation errors. I have no
access to the hardware.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hmm, the code was sleeping with interrupts disabled. This was not
good. Fix this by turning interrupts at an appropriate place. (The
race is protected by CLOSING flag.)
After the move, the code is identical to tty_port_close_end, so use
it!
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparation for a switch to tty_port_block_til_ready. We
need amiga_carrier_raised and amiga_dtr_rts. The implementation is
taken from startup, shutdown and current block_til_ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amiserial is the last user of serialP.h. Let's move struct
serial_state directly to amiserial and remove serialP crap from
includes. Finally, remove the header from the tree completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* instead of line, use tty->index or iterator...
* irq and type are left unset. So get rid of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to make the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* remove pointless checks (tty cannot be NULL at that points)
* fix some printks (use __func__, print text directly w/o using global
strings)
* remove some empty lines
This is the last patch for simserial. Overall, the driver is 400 lines
shorter. Being now at 560 lines.
It was tested using ski with a busybox userspace.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code to conform to the standard. Also make it readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Or the obsolete ones like:
"Let's have a little bit of fun"
I have never had fun with software. For fun, one needs hard-ware.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert shutdown to be tty_port_operations->shutdown. Then we can use
tty_port_hangup. (And we have to use tty_port_close.)
This means we no longer touch ASYNC_INITIALIZED, TTY_IO_ERROR. Also we
do not need to do any peculiar TTY logic in the file now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now we convert startup to be ->activate of tty_port. This means we
no longer care about INITIALIZED and TTY_IO_ERROR flags.
After we have ->activate much of the code may go as it duplicates what
tty_port_open does. In this case tty_port_open adds block_til_ready to
the path. But we do not define carrier hooks, so it is a noop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that we will not be surprised in the ISR anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I.e. remove more copied bloat.
The only change is that we wait_until_sent now. Which is what we
really should do.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is identical except locking. But added locks to protect
counts do not hurt here. Rather the contrary.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All ->start, ->stop and ->wait_until_sent are empty and need not be
defined. The time to remove them is now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to make the code more readable.
Since tport doesn't conflict with port anymore and there are not many
tport accessors left, do also s/\<tport\>/port/g.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's do a spin-off of serial_state structure with only needed
elements.
And remove serialP crap from includes.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* instead of line, use tty->index or an iterator
* icount is not made public, only the tx path increments it
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not use any of the preinitialized rs_state members for something
real. So there is no need to initialize them. At the places we used
them for printing, just print the values.
And since only one port is supported, get rid of the loop. This
simplifies simrs_init a heap. Thus we can handle fail paths in a
standard way without panicing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes flags' type to ulong which is appropriate for all the
set/clear_bits performed in the drivers..
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing special. Just remove count from serial_state and change all
users to use tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
