hci_conn_hold/put_device() is used to control when hci_conn->dev is no
longer needed and can be deleted from the system. Lets first look how they
are currently used throughout the code (excluding HIDP!).
All code that uses hci_conn_hold_device() looks like this:
...
hci_conn_hold_device();
hci_conn_add_sysfs();
...
On the other side, hci_conn_put_device() is exclusively used in
hci_conn_del().
So, considering that hci_conn_del() must not be called twice (which would
fail horribly), we know that hci_conn_put_device() is only called _once_
(which is in hci_conn_del()).
On the other hand, hci_conn_add_sysfs() must not be called twice, either
(it would call device_add twice, which breaks the device, see
drivers/base/core.c). So we know that hci_conn_hold_device() is also
called only once (it's only called directly before hci_conn_add_sysfs()).
So hold and put are known to be called only once. That means we can safely
remove them and directly call hci_conn_del_sysfs() in hci_conn_del().
But there is one issue left: HIDP also uses hci_conn_hold/put_device().
However, this case can be ignored and simply removed as it is totally
broken. The issue is, the only thing HIDP delays with
hci_conn_hold_device() is the removal of the hci_conn->dev from sysfs.
But, the hci_conn device has no mechanism to get notified when its own
parent (hci_dev) gets removed from sysfs. hci_dev_hold/put() does _not_
control when it is removed but only when the device object is created
and destroyed.
And hci_dev calls hci_conn_flush_*() when it removes itself from sysfs,
which itself causes hci_conn_del() to be called, but it does _not_ cause
hci_conn_del_sysfs() to be called, which is wrong.
Hence, we fix it to call hci_conn_del_sysfs() in hci_conn_del(). This
guarantees that a hci_conn object is removed from sysfs _before_ its
parent hci_dev is removed.
The changes to HIDP look scary, wrong and broken. However, if you look at
the HIDP session management, you will notice they're already broken in the
exact _same_ way (ever tried "unplugging" HIDP devices? Breaks _all_ the
time).
So this patch only makes HIDP look _scary_ and _obviously broken_. It does
not break HIDP itself, it already is!
See later patches in this series which fix HIDP to use proper
session-management.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch sends Reject Synchronous Connection Request Command when
hci_conn_timeout is triggered, and the SCO connection is in BT_CONNECT2
state. It prevents inconsistency if the remote host doesn't implement
properly the timeout for the connection request, and it removes the
connection reference left when the socket is closed for incoming SCO
connections.
[ 2650.129080] sco_sock_release: sock ffff8801ca417400, sk ffff88020c408800
[ 2650.129092] sco_sock_clear_timer: sock ffff88020c408800 state 6
[ 2650.129101] __sco_sock_close: sk ffff88020c408800 state 6 socket
ffff8801ca417400
[ 2650.129108] sco_chan_del: sk ffff88020c408800, conn ffff8801c650ea20,
err 104
[ 2650.129114] hci_conn_put: hcon ffff88020c40a800 orig refcnt 1
[ 2650.129128] sco_sock_kill: sk ffff88020c408800 state 9
[ 2650.129135] sco_sock_destruct: sk ffff88020c408800
[ 2650.138468] hci_conn_timeout: hcon ffff88020c40a800 state BT_CONNECT2
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes the status parameter of the l2cap_conn_add function.
The parameter 'status' is always 0.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes the memory allocation flags in the sco_conn_add
function, replacing the type to GFP_KERNEL. This function is executed
in process context and it is not called inside an atomic section.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().
hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.
But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.
To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.
Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We need to verify that the given sockets actually are l2cap sockets. If
they aren't, we are not supposed to access bt_sk(sock) and we shouldn't
start the session if the offsets turn out to be valid local BT addresses.
That is, if someone passes a TCP socket to HIDCONNADD, then we access some
random offset in the TCP socket (which isn't even guaranteed to be valid).
Fix this by checking that the socket is an l2cap socket.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
We print this error twice in the first error-path so remove it. One error
message is enough.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The driver init queue is no longer needed. This can be all handled
inside the drivers now. So remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some drivers require a special stage for their early init. This is
always specific to the driver or transport. So call back into driver to
allow bringing up the device.
The advantage with this stage is that the Bluetooth core is actually
handling the HCI layer now. This means that command and event processing
is available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a __hci_cmd_sync_ev function, analogous to
__hci_cmd_sync except that it also takes an event parameter to indicate
that the command completes with a special event instead of command
complete. Internally this new function takes advantage of the
hci_req_add_ev function introduced in the previous patch.
The primary expected user of this new function are the setup routines of
HCI drivers which may want to send custom commands and return only when
they have completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for having commands within HCI requests that do
not result in a command complete but some other event. This is at least
needed for some vendor specific commands to be issued in the
hdev->setup() procecure, but might also be useful for other commands.
The way that the support is implemented is by extending the skb control
buffer to have a field to indicate that the command is expected to
terminate with a special event. After sending the command each received
event can then be compared against this field through hdev->sent_cmd.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a helper function for sending a single HCI command
waiting for its completion and then returning back the parameters in the
resulting command complete event (if there was one).
The implementation is very similar to that of hci_req_sync() except that
instead of invocing a callback for sending HCI commands the function
constructs and sends one itself and after being woken up picks the last
received event from hdev->recv_evt (if it matches the right criteria)
and returns it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds tracking of received HCI events to the hci_dev struct.
This is necessary so that a subsequent patch can implement a function
for sending a single command synchronously and returning the resulting
command complete parameters in the function return value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes redundant whitespace from the HCI ldisc driver.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a check HCI_UART_REGISTERED before reading UART data in
the HCI UART H4 driver. UART data could arrive when inside the
hci_uart_tty_ioctl function after calling test_and_set_bit for
HCI_UART_PROTO_SET but before the hci_uart_set_proto function has
returned.
Backtrace:
[<c05f27ec>] (hci_recv_stream_fragment+0x0/0x74) from [<c04126f4>] (h4_recv+0x18/0x40)
r7:eb1d4d1c r6:eb7683b0 r5:eae8e800 r4:0000000c
[<c04126dc>] (h4_recv+0x0/0x40) from [<c0411870>] (hci_uart_tty_receive+0x6c/0x94)
r5:eae8e800 r4:eb768380
[<c0411804>] (hci_uart_tty_receive+0x0/0x94) from [<c027be88>] (flush_to_ldisc+0x16c/0x17c)
r6:eae8e8d8 r5:eae8e800 r4:eae8e8c8
[<c027bd1c>] (flush_to_ldisc+0x0/0x17c) from [<c0050ae8>] (process_one_work+0x144/0x4d4)
[<c00509a4>] (process_one_work+0x0/0x4d4) from [<c0051208>] (worker_thread+0x180/0x370)
[<c0051088>] (worker_thread+0x0/0x370) from [<c005617c>] (kthread+0x90/0x9c)
[<c00560ec>] (kthread+0x0/0x9c) from [<c003a3a0>] (do_exit+0x0/0x7ec)
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch removes the hci_req_cmd_status function since it is not
used anymore. The HCI request framework now considers the HCI command
has complete once the Command Status or Command Complete Event is
received.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the HCI request framework was properly fixed, the hci_req_sync
call, in hci_inquiry, will return as soon as the HCI command completes
(not the Inquiry procedure). However, in inquiry ioctl implementation,
we want to sleep the user process until the inquiry procedure finishes.
This patch changes hci_inquiry so, in case the HCI Inquiry command
was executed successfully, it waits the HCI_INQUIRY flag to be cleared.
This way, the user process will sleep until the inquiry procedure
finishes.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some HCI commands don't send a Command Complete Event once the HCI
command has completed so they require some special handling from the
HCI request framework. These HCI commands, however, send a Command
Status Event to indicate that the command has been received, and
that the controller is currently performing the task for the command.
So, in order to properly handle those HCI commands, the HCI request
framework should consider the HCI command has completed once the
Command Status Event is received.
This way, we fix some issues regarding the Inquiry command support,
as well as add support for all those HCI commands which would require
some special handling from the HCI request framework.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions are moved in preparation of later patches.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length is not according specification so better fix it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.
this commit will be squashed.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is deleted make sure to cleanup all packet
buffers related to that interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware signalling functionality needs the credit map firmware
events. This patch adds registration of a handler for this event.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware signalling needs to handle resources upon interface
events. This patch add calls in the interface event handling
routine.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use information from the device to determine the bands property
of the wiphy object. After this change the support of 80211n is
correctly presented in the bands property.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_sdbrcm_txpkt() a new packet is allocated and used to transmit
to firmware freeing up the original packet. However, that packet is
still referenced in firmware-signalling so this would result in a
double free. Using skb_cow() avoids this as the packet reference is
unchanged.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When taking care of packet alignment to 64-byte boundary padding may
be added between SDPCM header and CDC data. It clear both SDPCM header
space and padding space. Changed it to only clear padding space. In
filling the SDPCM header it uses unaligned access to set SDPCM software
header, but preceding code assures it is properly aligned.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Iad22f277f3496440ba4d2db771205714774570ac
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/76
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdbrcm_txpkt() calls brcmf_txcomplete() with
a parameter success. For this parameter it passes ret != 0, but
that condition is true upon failure.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
