172 %ECX<def> = MOV32rr %reg1039<kill>
180 INLINEASM <es:subl $5,$1
sbbl $3,$0>, 10, %EAX<def>, 14, %ECX<earlyclobber,def>, 9, %EAX<kill>,
36, <fi#0>, 1, %reg0, 0, 9, %ECX<kill>, 36, <fi#1>, 1, %reg0, 0
188 %EAX<def> = MOV32rr %EAX<kill>
196 %ECX<def> = MOV32rr %ECX<kill>
204 %ECX<def> = MOV32rr %ECX<kill>
212 %EAX<def> = MOV32rr %EAX<kill>
220 %EAX<def> = MOV32rr %EAX
228 %reg1039<def> = MOV32rr %ECX<kill>
The early clobber operand ties ECX input to the ECX def.
The live interval of ECX is represented as this:
%reg20,inf = [46,47:1)[174,230:0) 0@174-(230) 1@46-(47)
The right way to represent this is something like
%reg20,inf = [46,47:2)[174,182:1)[181:230:0) 0@174-(182) 1@181-230 @2@46-(47)
Of course that won't work since that means overlapping live ranges defined by two val#.
The workaround for now is to add a bit to val# which says the val# is redefined by a early clobber def somewhere. This prevents the move at 228 from being optimized away by SimpleRegisterCoalescing::AdjustCopiesBackFrom.
llvm-svn: 61259
that have i32 immediates so that they get selected first. This
currently only matters in the JIT, as assemblers will
automatically use the smallest encoding.
llvm-svn: 61250
- Use SplitBlockPredecessors to factor out common predecessors of the critical edge destination. This is disabled for now due to some regressions.
llvm-svn: 61248
The EH_frame and .eh symbols are now private, except for darwin9 and earlier.
The patch also fixes the definition of PrivateGlobalPrefix on pcc linux.
llvm-svn: 61242
The problematic part of this patch is that we were out of attribute bits,
requiring some fancy bit hacking to make it fit (by shrinking alignment)
without breaking existing users or the file format.
This change will require users to rebuild llvm-gcc to match llvm.
llvm-svn: 61239
and the RegisterScavenger not to expect traditional liveness
techniques are applicable to these registers, since we don't fully
modify the effects of push and pop after stackification.
llvm-svn: 61179
my last patch to this file.
The issue there was that all uses of an IV inside a loop
are actually references to Base[IV*2], and there was one
use outside that was the same but LSR didn't see the base
or the scaling because it didn't recurse into uses outside
the loop; thus, it used base+IV*scale mode inside the loop
instead of pulling base out of the loop. This was extra bad
because register pressure later forced both base and IV into
memory. Doing that recursion, at least enough
to figure out addressing modes, is a good idea in general;
the change in AddUsersIfInteresting does this. However,
there were side effects....
It is also possible for recursing outside the loop to
introduce another IV where there was only 1 before (if
the refs inside are not scaled and the ref outside is).
I don't think this is a common case, but it's in the testsuite.
It is right to be very aggressive about getting rid of
such introduced IVs (CheckForIVReuse and the handling of
nonzero RewriteFactor in StrengthReduceStridedIVUsers).
In the testcase in question the new IV produced this way
has both a nonconstant stride and a nonzero base, neither
of which was handled before. (This patch does not handle
all the cases where this can happen.) And when inserting
new code that feeds into a PHI, it's right to put such
code at the original location rather than in the PHI's
immediate predecessor(s) when the original location is outside
the loop (a case that couldn't happen before)
(RewriteInstructionToUseNewBase); better to avoid making
multiple copies of it in this case.
Everything above is exercised in
CodeGen/X86/lsr-negative-stride.ll (and ifcvt4 in ARM which is
the same IR).
llvm-svn: 61178
- ability to insert previously created instructions using a builder
- creation of aliases
- creation of inline asm constants
Patch by Zoltan Varga!
llvm-svn: 61153
