Add aliases for the vpush/vpop mnemonics to the VFP load/store multiple
writeback instructions w/ SP as the base pointer.
rdar://9683231
llvm-svn: 133932
When the destination operand is the same as the first source register
operand for arithmetic instructions, the destination operand may be omitted.
For example, the following two instructions are equivalent:
sub r2, r2, #6
sub r2, #6
rdar://9682597
llvm-svn: 133925
Removed the check that peeks past EXTRA_SUBREG, which I don't think
makes sense any more. Intead treat it as a normal register def. No
significant affect on x86 or ARM benchmarks.
llvm-svn: 133917
alloca that only holds a copy of a global and we're going to replace the users
of the alloca with that global, just nuke the lifetime intrinsics. Part of
PR10121.
llvm-svn: 133905
Both become <earlyclobber> defs on the INLINEASM MachineInstr, but we
now use two different asm operand kinds.
The new Kind_Clobber is treated identically to the old
Kind_RegDefEarlyClobber for now, but x87 floating point stack inline
assembly does care about the difference.
This will pop a register off the stack:
asm("fstp %st" : : "t"(x) : "st");
While this will pop the input and push an output:
asm("fst %st" : "=&t"(r) : "t"(x));
We need to know if ST0 was a clobber or an output operand, and we can't
depend on <dead> flags for that.
llvm-svn: 133902
The INLINEASM MachineInstrs have an immediate operand describing each
original inline asm operand. Decode the bits in MachineInstr::print() so
it is easier to read:
INLINEASM <es:rorq $1,$0>, $0:[regdef], %vreg0<def>, %vreg1<def>, $1:[imm], 1, $2:[reguse] [tiedto:$0], %vreg2, %vreg3, $3:[regdef-ec], %EFLAGS<earlyclobber,imp-def>
llvm-svn: 133901
The .b8 operations in PTX are far more limiting than I first thought. The mov operation isn't even supported, so there's no way of converting a .pred value into a .b8 without going via .b16, which is
not sensible. An improved implementation needs to use the fact that loads and stores automatically extend and truncate to implement support for EXTLOAD and TRUNCSTORE in order to correctly support
boolean values.
llvm-svn: 133873
Move the target-specific RecordRelocation logic out of the generic MC
MachObjectWriter and into the target-specific object writers. This allows
nuking quite a bit of target knowledge from the supposedly target-independent
bits in lib/MC.
llvm-svn: 133844
The fixup value comes in as the whole 32-bit value, so for the lo16 fixup,
the upper bits need to be masked off. Previously we assumed the masking had
already been done and asserted.
rdar://9635991
llvm-svn: 133818
The i8 type is required for boolean values, but can only use ld, st and mov instructions. The i1 type continues to be used for predicates.
llvm-svn: 133814
instructions can be used to match combinations of multiply/divide and VCVT
(between floating-point and integer, Advanced SIMD). Basically the VCVT
immediate operand that specifies the number of fraction bits corresponds to a
floating-point multiply or divide by the corresponding power of 2.
For example, VCVT (floating-point to fixed-point, Advanced SIMD) can replace a
combination of VMUL and VCVT (floating-point to integer) as follows:
Example (assume d17 = <float 8.000000e+00, float 8.000000e+00>):
vmul.f32 d16, d17, d16
vcvt.s32.f32 d16, d16
becomes:
vcvt.s32.f32 d16, d16, #3
Similarly, VCVT (fixed-point to floating-point, Advanced SIMD) can replace a
combinations of VCVT (integer to floating-point) and VDIV as follows:
Example (assume d17 = <float 8.000000e+00, float 8.000000e+00>):
vcvt.f32.s32 d16, d16
vdiv.f32 d16, d17, d16
becomes:
vcvt.f32.s32 d16, d16, #3
llvm-svn: 133813
.file and .loc directives.
Ideally, we would utilize the existing support in AsmPrinter for this, but
I cannot find a way to get .file and .loc directives to print without the
rest of the associated DWARF sections, which ptxas cannot handle.
llvm-svn: 133812
enables SelectionDAG::getLoad at MipsISelLowering.cpp:1914 to return a
pre-existing node instead of redundantly create a new node every time it is
called.
llvm-svn: 133811
