SystemZTargetLowering::emitStringWrapper() previously loaded the character
into R0 before the loop and made R0 live on entry. I'd forgotten that
allocatable registers weren't allowed to be live across blocks at this stage,
and it confused LiveVariables enough to cause a miscompilation of f3 in
memchr-02.ll.
This patch instead loads R0 in the loop and leaves LICM to hoist it
after RA. This is actually what I'd tried originally, but I went for
the manual optimisation after noticing that R0 often wasn't being hoisted.
This bug forced me to go back and look at why, now fixed as r188774.
We should also try to optimize null checks so that they test the CC result
of the SRST directly. The select between null and the SRST GPR result could
then usually be deleted as dead.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188779 91177308-0d34-0410-b5e6-96231b3b80d8
Post-RA LICM keeps three sets of registers: PhysRegDefs, PhysRegClobbers
and TermRegs. When it sees a definition of R it adds all aliases of R
to the corresponding set, so that when it needs to test for membership
it only needs to test a single register, rather than worrying about
aliases there too. E.g. the final candidate loop just has:
unsigned Def = Candidates[i].Def;
if (!PhysRegClobbers.test(Def) && ...) {
to test whether register Def is multiply defined.
However, there was also a shortcut in ProcessMI to make sure we didn't
add candidates if we already knew that they would fail the final test.
This shortcut was more pessimistic than the final one because it
checked whether _any alias_ of the defined register was multiply defined.
This is too conservative for targets that define register pairs.
E.g. on z, R0 and R1 are sometimes used as a pair, so there is a
128-bit register that aliases both R0 and R1. If a loop used
R0 and R1 independently, and the definition of R0 came first,
we would be able to hoist the R0 assignment (because that used
the final test quoted above) but not the R1 assignment (because
that meant we had two definitions of the paired R0/R1 register
and would fail the shortcut in ProcessMI).
This patch just uses the same check for the ProcessMI shortcut as
we use in the final candidate loop.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188774 91177308-0d34-0410-b5e6-96231b3b80d8
For now this matches the equivalent of (neg (abs ...)), which did hit a few
times in projects/test-suite. We should probably also match cases where
absolute-like selects are used with reversed arguments.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188671 91177308-0d34-0410-b5e6-96231b3b80d8
This first cut is pretty conservative. The final argument register (R6)
is call-saved, so we would need to make sure that the R6 argument to a
sibling call is the same as the R6 argument to the calling function,
which seems worth keeping as a separate patch.
Saying that integer truncations are free means that we no longer
use the extending instructions LGF and LLGF for spills in int-conv-09.ll
and int-conv-10.ll. Instead we treat the registers as 64 bits wide and
truncate them to 32-bits where necessary. I think it's unlikely we'd
use LGF and LLGF for spills in other situations for the same reason,
so I'm removing the tests rather than replacing them. The associated
code is generic and applies to many more instructions than just
LGF and LLGF, so there is no corresponding code removal.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188669 91177308-0d34-0410-b5e6-96231b3b80d8
Generalize r188163 to cope with return types other than MVT::i32, just
as the existing visitMemCmpCall code did. I've split this out into a
subroutine so that it can be used for other upcoming patches.
I also noticed that I'd used the wrong API to record the out chain.
It's a load that uses DAG.getRoot() rather than getRoot(), so the out
chain should go on PendingLoads. I don't have a testcase for that because
we don't do any interesting scheduling on z yet.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188540 91177308-0d34-0410-b5e6-96231b3b80d8
r188163 used CLC to implement memcmp. Code that compares the result
directly against zero can test the CC value produced by CLC, but code
that needs an integer result must use IPM. The sequence I'd used was:
ipm <reg>
sll <reg>, 2
sra <reg>, 30
but I'd forgotten that this inverts the order, so that CC==1 ("less")
becomes an integer greater than zero, and CC==2 ("greater") becomes
an integer less than zero. This sequence should only be used if the
CLC arguments are reversed to compensate. The problem then is that
the branch condition must also be reversed when testing the CLC
result directly.
Rather than do that, I went for a different sequence that works with
the natural CLC order:
ipm <reg>
srl <reg>, 28
rll <reg>, <reg>, 31
One advantage of this is that it doesn't clobber CC. A disadvantage
is that any sign extension to 64 bits must be done separately,
rather than being folded into the shifts.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188538 91177308-0d34-0410-b5e6-96231b3b80d8
- Instead of setting the suffixes in a bunch of places, just set one master
list in the top-level config. We now only modify the suffix list in a few
suites that have one particular unique suffix (.ml, .mc, .yaml, .td, .py).
- Aside from removing the need for a bunch of lit.local.cfg files, this enables
4 tests that were inadvertently being skipped (one in
Transforms/BranchFolding, a .s file each in DebugInfo/AArch64 and
CodeGen/PowerPC, and one in CodeGen/SI which is now failing and has been
XFAILED).
- This commit also fixes a bunch of config files to use config.root instead of
older copy-pasted code.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188513 91177308-0d34-0410-b5e6-96231b3b80d8
For now this is restricted to fixed-length comparisons with a length
in the range [1, 256], as for memcpy() and MVC.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@188163 91177308-0d34-0410-b5e6-96231b3b80d8
This follows the same lines as the integer code. In the end it seemed
easier to have a second 4-bit mask in TSFlags to specify the compare-like
CC values. That eats one more TSFlags bit than adding a CCHasUnordered
would have done, but it feels more concise.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187883 91177308-0d34-0410-b5e6-96231b3b80d8
This patch just uses a peephole test for "add; compare; branch" sequences
within a single block. The IR optimizers already convert loops to
decrement-and-branch-on-nonzero form in some cases, so even this
simplistic test triggers many times during a clang bootstrap and
projects/test-suite run. It looks like there are still cases where we
need to more strongly prefer branches on nonzero though. E.g. I saw a
case where a loop that started out with a check for 0 ended up with a
check for -1. I'll try to look at that sometime.
I ended up adding the Reference class because MachineInstr::readsRegister()
doesn't check for subregisters (by design, as far as I could tell).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187723 91177308-0d34-0410-b5e6-96231b3b80d8
This also fixes a bug in the predication of LR to LOCR: I'd forgotten
that with these in-place instruction builds, the implicit operands need
to be added manually. I think this was latent until now, but is tested
by int-cmp-45.c. It also adds a CC valid mask to STOC, again tested by
int-cmp-45.c.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187573 91177308-0d34-0410-b5e6-96231b3b80d8
Convert >= 1 to > 0, etc. Using comparison with zero isn't a win on its own,
but it exposes more opportunities for CC reuse (the next patch).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187571 91177308-0d34-0410-b5e6-96231b3b80d8
The loop optimizers were assuming that scales > 1 were OK. I think this
is actually a bug in TargetLoweringBase::isLegalAddressingMode(),
since it seems to be trying to reject anything that isn't r+i or r+r,
but it has no default case for scales other than 0, 1 or 2. Implementing
the hook for z means that z can no longer test any change there though.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187497 91177308-0d34-0410-b5e6-96231b3b80d8
Extend r187495 to conditional loads. I split this out because the
easiest way seemed to be to force a particular operand order in
SystemZISelDAGToDAG.cpp.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187496 91177308-0d34-0410-b5e6-96231b3b80d8
System z branches have a mask to select which of the 4 CC values should
cause the branch to be taken. We can invert a branch by inverting the mask.
However, not all instructions can produce all 4 CC values, so inverting
the branch like this can lead to some oddities. For example, integer
comparisons only produce a CC of 0 (equal), 1 (less) or 2 (greater).
If an integer EQ is reversed to NE before instruction selection,
the branch will test for 1 or 2. If instead the branch is reversed
after instruction selection (by inverting the mask), it will test for
1, 2 or 3. Both are correct, but the second isn't really canonical.
This patch therefore keeps track of which CC values are possible
and uses this when inverting a mask.
Although this is mostly cosmestic, it fixes undefined behavior
for the CIJNLH in branch-08.ll. Another fix would have been
to mask out bit 0 when generating the fused compare and branch,
but the point of this patch is that we shouldn't need to do that
in the first place.
The patch also makes it easier to reuse CC results from other instructions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187495 91177308-0d34-0410-b5e6-96231b3b80d8
r187116 moved compare-and-branch generation from the instruction-selection
pass to the peephole optimizer (via optimizeCompare). It turns out that even
this is a bit too early. Fused compare-and-branch instructions don't
interact well with predication, where a CC result is needed. They also
make it harder to reuse the CC side-effects of earlier instructions
(not yet implemented, but the subject of a later patch).
Another problem was that the AnalyzeBranch family of routines weren't
handling compares and branches, so we weren't able to reverse the fused
form in cases where we would reverse a separate branch. This could have
been fixed by extending AnalyzeBranch, but given the other problems,
I've instead moved the fusing to the long-branch pass, which is also
responsible for the opposite transformation: splitting out-of-range
compares and branches into separate compares and long branches.
I've added a test for the AnalyzeBranch problem. A test for the
predication problem is included in the next patch, which fixes a bug
in the choice of CC mask.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187494 91177308-0d34-0410-b5e6-96231b3b80d8
r186399 aggressively used the RISBG instruction for immediate ANDs,
both because it can handle some values that AND IMMEDIATE can't,
and because it allows the destination register to be different from
the source. I realized later while implementing the distinct-ops
support that it would be better to leave the choice up to
convertToThreeAddress() instead. The AND IMMEDIATE form is shorter
and is less likely to be cracked.
This is a problem for 32-bit ANDs because we assume that all 32-bit
operations will leave the high word untouched, whereas RISBG used in
this way will either clear the high word or copy it from the source
register. The patch uses the z196 instruction RISBLG for this instead.
This means that z10 will be restricted to NILL, NILH and NILF for
32-bit ANDs, but I think that should be OK for now. Although we're
using z10 as the base architecture, the optimization work is going
to be focused more on z196 and zEC12.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187492 91177308-0d34-0410-b5e6-96231b3b80d8
Before the patch we took advantage of the fact that the compare and
branch are glued together in the selection DAG and fused them together
(where possible) while emitting them. This seemed to work well in practice.
However, fusing the compare so early makes it harder to remove redundant
compares in cases where CC already has a suitable value. This patch
therefore uses the peephole analyzeCompare/optimizeCompareInstr pair of
functions instead.
No behavioral change intended, but it paves the way for a later patch.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187116 91177308-0d34-0410-b5e6-96231b3b80d8
As with the stores, these instructions can trap when the condition is false,
so they are only used for things like (cond ? x : *ptr).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187112 91177308-0d34-0410-b5e6-96231b3b80d8
These instructions are allowed to trap even if the condition is false,
so for now they are only used for "*ptr = (cond ? x : *ptr)"-style
constructs.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@187111 91177308-0d34-0410-b5e6-96231b3b80d8
The insn definitions themselves crept into r186689, sorry.
This should be the last of the distinct-ops instructions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186690 91177308-0d34-0410-b5e6-96231b3b80d8
Follows the same lines as r186686, but much more limited, since we only
use ADD LOGICAL for multi-i64 additions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186689 91177308-0d34-0410-b5e6-96231b3b80d8
The atomic tests assume the two-operand forms, so I've restricted them to z10.
Running and-01.ll, or-01.ll and xor-01.ll for z196 as well as z10 shows why
using convertToThreeAddress() is better than exposing the three-operand forms
first and then converting back to two operands where possible (which is what
I'd originally tried). Using the three-operand form first stops us from
taking advantage of NG, OG and XG for spills.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186683 91177308-0d34-0410-b5e6-96231b3b80d8
The original code only folded SRA into ROTATE ... SELECTED BITS
if there was no outer shift. This patch splits out that check
and generalises it slightly. The extra cases aren't really that
interesting, but this is paving the way for RNSBG support.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186571 91177308-0d34-0410-b5e6-96231b3b80d8
Another patch in the series to make more use of R.SBG. This one extends
r186072 and r186073 to handle cases where the AND is inside the shift.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186399 91177308-0d34-0410-b5e6-96231b3b80d8
This update was done with the following bash script:
find test/CodeGen -name "*.ll" | \
while read NAME; do
echo "$NAME"
if ! grep -q "^; *RUN: *llc.*debug" $NAME; then
TEMP=`mktemp -t temp`
cp $NAME $TEMP
sed -n "s/^define [^@]*@\([A-Za-z0-9_]*\)(.*$/\1/p" < $NAME | \
while read FUNC; do
sed -i '' "s/;\(.*\)\([A-Za-z0-9_-]*\):\( *\)$FUNC: *\$/;\1\2-LABEL:\3$FUNC:/g" $TEMP
done
sed -i '' "s/;\(.*\)-LABEL-LABEL:/;\1-LABEL:/" $TEMP
sed -i '' "s/;\(.*\)-NEXT-LABEL:/;\1-NEXT:/" $TEMP
sed -i '' "s/;\(.*\)-NOT-LABEL:/;\1-NOT:/" $TEMP
sed -i '' "s/;\(.*\)-DAG-LABEL:/;\1-DAG:/" $TEMP
mv $TEMP $NAME
fi
done
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186280 91177308-0d34-0410-b5e6-96231b3b80d8
Normal (sext (setcc ...)) sequences are optimised into
(select_cc ..., -1, 0) by DAGCombiner::visitSIGN_EXTEND.
However, this is deliberately not done for vectors, and after
vector type legalization we have (sext_inreg (setcc ...)) instead.
I wondered about trying to extend DAGCombiner to handle this case too,
but it seemed to be a loss on some other targets I tried, even those for
which SETCC isn't "legal" and SELECT_CC is.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186149 91177308-0d34-0410-b5e6-96231b3b80d8
If the source of these instructions is spilled we should load the destination.
If the destination is spilled we should store the source.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186147 91177308-0d34-0410-b5e6-96231b3b80d8
RISBG can handle some ANDs for which no AND IMMEDIATE exists.
It also acts as a three-operand AND for some cases where an
AND IMMEDIATE could be used instead.
It might be worth adding a pass to replace RISBG with AND IMMEDIATE
in cases where the register operands end up being the same and where
AND IMMEDIATE is smaller.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@186072 91177308-0d34-0410-b5e6-96231b3b80d8
Look for patterns of the form (store (load ...), ...) in which the two
locations are known not to partially overlap. (Identical locations are OK.)
These sequences are better implemented by MVC unless either the load or
the store could use RELATIVE LONG instructions.
The testcase showed that we weren't using LHRL and LGHRL for extload16,
only sextloadi16. The patch fixes that too.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185919 91177308-0d34-0410-b5e6-96231b3b80d8
Use "STC;MVC" for memsets that are too big for two STCs or MV...Is yet
small enough for a single MVC. As with memcpy, I'm leaving longer cases
till later.
The number of tests might seem excessive, but f33 & f34 from memset-04.ll
failed the first cut because I'd not added the "?:" on the calculation
of Size1.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185918 91177308-0d34-0410-b5e6-96231b3b80d8
Use MVC for memcpy in cases where a single MVC is enough. Using MVC is
a win for longer copies too, but I'll leave that for later.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185802 91177308-0d34-0410-b5e6-96231b3b80d8
