Kenneth D. Merry
57b6261f94
Prior to this change, the CRN (Command Reference Number) is reset on any firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which specifies that the CRN should only be reset in response to a LIP Reset (LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS actions as conditions for resetting the CRN for the associated initiator port. These violations manifest themselves when the HBA is removed from the loop, or a target device is removed (especially during an outstanding command) without power cycling. If the HBA and and the target device determine upon re-establishing the loop that no PLOGI or PRLI is required, and the target does not issue a LIPxy to the initiator, the CRN for the target will have been improperly reset by the isp driver. As a result, the target port will silently ignore all FCP commands issued during the device probe (which will time out) preventing the device from attaching. This change corrects thie CRN reset behavior in response to loop state changes, also introduces CRN resets for the above mentioned ELS actions as encountered through async PDB change events. This change also adds cleanup of outstanding commands in isp_loop_dead() that was previously missing. sys/dev/isp/isp.c Add the last login state to debug output when syncing the pdb sys/dev/isp/isp_freebsd.c Replace binary statement setting aborted ccb status in isp_watchdog() with the XS_SETERR macro used elsewhere In isp_loop_dead(), abort or complete pending commands as done in isp_watchdog() In isp_async(), segregate the ISPASYNC_LOOP_RESET action from ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP fallthroughs, and only reset the CRN in the RESET case. Also add checks to handle false LOOP RESET actions that do not have a proper associated LIP primitive, and log the primitive in the debug messages In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and only reset the CRN in the DEV_CHANGED action In isp_async(), when processing an ISPASYNC_CHANGE_PDB status, reset CRN(s) for the associated nphdl (or all ports) if the change reason is some form of ELS login/logout. Also remove assignment to fc since it is not used in the scope sys/dev/isp/ispmbox.h Add macro definition for the global N-Port handle, and correct a macro typo 'PDB24XX_AE_PRLI_DONJE' sys/dev/isp/ispvar.h Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for more legible code when determining if an AL_PD port matches the portid for a given struct fcparam* by value or by virtue of the AL_PD port being 0xFF Submitted by: Reid Linnemann Sponsored by: Spectra Logic MFC after: 1 week
FreeBSD Source:
This is the top level of the FreeBSD source directory. This file
was last revised on:
FreeBSD
For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information).
The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree. See build(7) and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables.
The buildkernel and installkernel targets build and install
the kernel and the modules (see below). Please see the top of
the Makefile in this directory for more information on the
standard build targets and compile-time flags.
Building a kernel is a somewhat more involved process. See build(7), config(8), and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html for more information.
Note: If you want to build and install the kernel with the
buildkernel and installkernel targets, you might need to build
world before. More information is available in the handbook.
The kernel configuration files reside in the sys/<arch>/conf
sub-directory. GENERIC is the default configuration used in release builds.
NOTES contains entries and documentation for all possible
devices, not just those commonly used.
Source Roadmap:
bin System/user commands.
cddl Various commands and libraries under the Common Development
and Distribution License.
contrib Packages contributed by 3rd parties.
crypto Cryptography stuff (see crypto/README).
etc Template files for /etc.
gnu Various commands and libraries under the GNU Public License.
Please see gnu/COPYING* for more information.
include System include files.
kerberos5 Kerberos5 (Heimdal) package.
lib System libraries.
libexec System daemons.
release Release building Makefile & associated tools.
rescue Build system for statically linked /rescue utilities.
sbin System commands.
secure Cryptographic libraries and commands.
share Shared resources.
sys Kernel sources.
tests Regression tests which can be run by Kyua. See tests/README
for additional information.
tools Utilities for regression testing and miscellaneous tasks.
usr.bin User commands.
usr.sbin System administration commands.
For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see:
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html