a078d40b80
1548bee835 Update glsm df7c8aebea Update glsm git-subtree-dir: libretro-common git-subtree-split: 1548bee835ab5fa2d120a4859ff653a5f128de1f
5.2 KiB
RetroArch Exynos-G2D video driver
The Exynos-G2D video driver for RetroArch uses the Exynos DRM layer for presentation and the Exynos G2D block to scale and blit the emulator framebuffer to the screen. The G2D subsystem is a separate functional block on modern Samsung Exynos SoCs (in particular Exynos4412 and Exynos5250) that accelerates various kind of 2D blit operations. It can fill, copy, scale and blend pixel buffers and therefore provides adequate functionality for RetroArch purposes.
Reasons to use the driver
Hardware accelerated rendering on devices based on an Exynos SoC is usually restricted to the use of the GPU block, which is either a Mali or PowerVR IP. Both GPU types have the problem that interfacing with them requires a proprietary driver stack, comprised of kernel and userspace code. While the kernel code is open source, the userspace code is only available as a binary blob to the enduser.
If you want to use such a device with an upstream kernel, the GPU block will most likely not work for you. Also the chances of Mali or PowerVR kernel code being accepted upstream is very slim. Still, one might want to ask the question if using the GPU block for such trivial operations (basically scale and blend) is the right approach in the first place.
Since the G2D block is present on all modern Exynos SoCs, the natural way of proceeding would be to use it instead of the GPU block. The G2D is still a dedicated piece of hardware, so all operations are offloaded from the CPU. It should be noted though, that using the G2D instead of the GPU removes the possibility to use GPU shaders to enhance the image quality of your emulator core of choice. If the user relies on these enhancements, then he's advised to continue using the GPU, most likely by using the EGL/GLES video driver.
The author uses a Hardkernel ODROID-X2, which is an developer board powered by an Exynos4412 SoC. The vendor supplied kernel, a Linux tree based on the 3.8.y branch, currently offers no way to use the G2D because of issues related to clock setup. However upstreaming work is in progress and a tree based on 3.15.y, with some slight modifications, is available from here:
Please refer to the minimalistic documentation in README-ODROID for setup.
Performance analysis
Some simple benchmarking was done to evaluate the performance of the G2D block. The test run was done with the snes9x-next emulation core and a game title that uses a native resolution of 256x224 pixels. The output screen was configured to a 1280x720 mode. Scaling to the output screen was done by keeping the native aspect ratio. In this case this would result in an output rectangle of size 822x720.
total memcpy calls: 18795
total g2d calls: 18795
total memcpy time: 8.978532 seconds
total g2d time: 29.703944 seconds
average time per memcpy call: 477.708540 microseconds
average time per g2d call: 1580.417345 microseconds
The average time to display the emulator framebuffer on screen is roughly 2058 microseconds, or around 486 frames per second. Assuming that the time consumption increases linearly with the amount of pixels processed, which is usually a safe assumption, scaling to an output rectangle of size 1920x1080 would yield a average duration of 7207 microseconds, which is still 138 frames per second.
Configuration
The video driver uses the libdrm API to interface with the DRM. Some patches are still missing in the upstream tree, therefore the user is advised to use the 'exynos' branch of the repository mentioned below.
Make sure that the Exynos API support is enabled. If you're building libdrm from source, then use
./configure --enable-exynos-experimental-api
to enable it.
The video driver name is 'exynos'. It honors the following video settings:
- video_monitor_index
- video_fullscreen_x and video_fullscreen_y
The monitor index maps to the DRM connector index. If it is zero, then it just selects the first 'sane' connector, which means that it is connected to a display device and it provides at least one useable mode. If the value is non-zero, it forces the selection of this connector. For example, on the author's ODROID-X2, with an odroid-3.15.y kernel, the HDMI connector has index 1.
The two fullscreen parameters select the mode the DRM should select. If zero, the native connector mode is selected. If non-zero, the DRM tries to select the wanted mode. This might fail if the mode is not available from the connector.
Issues and TODOs
The driver still suffers from some issues.
- The aspect ratio computation can be improved. In particular the user supplied aspect ratio is currently unused.
- Font rendering and blitting is very inefficient since the backing buffer is cleared every frame. Introduce a invalidation rectangle which covers the region where font glyphs are drawn, and then only clear this region. Also consider converting the buffer to A8 color format and using global color (not sure if this is possible).
- Temporary GEM buffers are used as source for blitting operations. Support for the IOMMU has to be enabled, so that one can use the 'userptr' functionality.
- More TODOs are pointed out in the code itself.