Move the flash and DRAM to the end of the SoC memmap table.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-5-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC supports booting from several sources, which are
controlled using the Mode Select (MSEL[3:0]) pins on the chip.
Typically, the boot process runs through several stages before it
begins execution of user-provided programs.
The SoC supports booting from memory-mapped QSPI flash, which is
how start_in_flash property is used for at present. This matches
MSEL = 1 configuration (QSPI0).
Typical booting flows involve the Zeroth Stage Boot Loader (ZSBL).
It's not necessary for QEMU to implement the full ZSBL ROM codes,
because we know ZSBL downloads the next stage program into the L2
LIM at address 0x8000000 and executes from there. We can bypass
the whole ZSBL execution and use "-bios" to load the next stage
program directly if MSEL indicates a ZSBL booting flow.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-4-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per the SiFive manual, all E/U series CPU cores' reset vector is
at 0x1004. Update our codes to match the hardware.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-3-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Current IBEX CPU init routine name seems to be too generic.
Since it uses a different reset vector from the generic one,
it merits a dedicated name.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On SiFive FU540 SoC, the value stored at physical address 0x1000
stores the MSEL pin state that is used to control the next boot
location that ROM codes jump to.
Add a new property msel to sifive_u machine for this.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-12-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In prepration to add more properties to this machine, rename the
existing serial property get/set functions to a generic name.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-11-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The HiFive Unleashed board wires GPIO pin#10 to the input of the
system reset signal. Let's set up the GPIO pin#10 and insert a
"gpio-restart" device tree node so that reboot is now functional
with QEMU 'sifive_u' machine.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-10-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the GPIO output IRQs are triggered each time any GPIO
register is written. However this is not correct. We should only
trigger the output IRQ when the pin is configured as output enable.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-9-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a GPIO controller with 16 GPIO lines.
This hooks the exsiting SiFive GPIO model to the SoC, and adds its
device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-8-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a new property to represent the number of GPIO pins supported
by the GPIO controller.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-7-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Do various minor clean-ups to the exisiting codes for:
- coding convention conformance
- remove unnecessary blank lines
- spell SiFive correctly
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-6-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Upstream U-Boot v2020.07 codes switch to access SiFive FU540 OTP
based on device tree information. Let's generate the device tree
node for OTP.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-5-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to retrieve all PLIC IRQ information in order to
just connect the GEM IRQ. Use qdev_get_gpio_in() directly like
what is done for other peripherals.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-4-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but opentitan codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-3-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but sifive_e codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Ibex core contains a PLIC that although similar to the RISC-V spec
is not RISC-V spec compliant.
This patch implements a Ibex PLIC in a somewhat generic way.
As the current RISC-V PLIC needs tidying up, my hope is that as the Ibex
PLIC move towards spec compliance this PLIC implementation can be
updated until it can replace the current PLIC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is the initial commit of the Ibex UART device. Serial TX is
working, while RX has been implemeneted but untested.
This is based on the documentation from:
https://docs.opentitan.org/hw/ip/uart/doc/
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
Call the helper_hyp_tlb_flush() function on hfence instructions which
will generate an illegal insruction execption if we don't have
permission to flush the Hypervisor level TLBs.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Also correct the name of the VVMA instruction.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Adding a _ to keep some consistency among the CPU init routines.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1591837729-27486-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to have two functions that have almost the same
codes for 32-bit and 64-bit imacu CPUs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1591837729-27486-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to have two functions that have almost the same
codes for 32-bit and 64-bit gcsu CPUs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1591837729-27486-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to have two functions that have exactly the same
codes for 32-bit and 64-bit base CPUs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591837729-27486-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591837729-27486-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The function that makes NaN-boxing when a 32-bit value is assigned
to a 64-bit FP register is split out to a helper gen_nanbox_fpr().
Then it is applied in translating of the FLW instruction.
Signed-off-by: Ian Jiang <ianjiang.ict@gmail.com>
Message-Id: <20200128003707.17028-1-ianjiang.ict@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Version: GnuPG v1
iQEcBAABAgAGBQJe62kmAAoJEO8Ells5jWIRZfUH/2bPZrhG4QEKNWbm1LXzam+0
4dzG3A7vYTKWjfbpzcWtUAELO+4SiUe/IU3gYMiyeWNDKjwm5hX/FMCFjnR1IZXl
wQ7cvr/7TIsxt9HyrjIkh03PkJBGpCD3uO0DkGd1siDmKLOFNRt0uLsmSvA7Ydvo
2hH/tc/plYoQAxPSbXBmIqg9hRrks/QAw2kfPba7Adhtzg5x2XrUrP+UOW8NmWcL
xSo02ExPUSdzPX6I4Enwm1c1KiytlQ77LvazpI2NBlejsI4nqa0Y1WJW7WJ4RMGo
E1kWDiKt69MoT1SgH7UJnF/ISyUuldksD4fuual5UOysCpwpbAIBKh6/Yod6k0M=
=3+ix
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 18 Jun 2020 14:16:22 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request: (33 commits)
net: Drop the NetLegacy structure, always use Netdev instead
net: Drop the legacy "name" parameter from the -net option
hw/net/e1000e: Do not abort() on invalid PSRCTL register value
colo-compare: Fix memory leak in packet_enqueue()
net/colo-compare.c: Correct ordering in complete and finalize
net/colo-compare.c: Check that colo-compare is active
net/colo-compare.c: Only hexdump packets if tracing is enabled
net/colo-compare.c: Fix deadlock in compare_chr_send
chardev/char.c: Use qemu_co_sleep_ns if in coroutine
net/colo-compare.c: Create event_bh with the right AioContext
net: use peer when purging queue in qemu_flush_or_purge_queue_packets()
net: cadence_gem: Fix RX address filtering
net: cadence_gem: TX_LAST bit should be set by guest
net: cadence_gem: Update the reset value for interrupt mask register
net: cadnece_gem: Update irq_read_clear field of designcfg_debug1 reg
net: cadence_gem: Add support for jumbo frames
net: cadence_gem: Fix up code style
net: cadence_gem: Move tx/rx packet buffert to CadenceGEMState
net: cadence_gem: Set ISR according to queue in use
net: cadence_gem: Define access permission for interrupt registers
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Migration:
HMP/migration and test changes from Mao Zhongyi
multifd fix from Laurent Vivier
HMP
qom-set partial reversion/change from David Hildenbrand
now you need -j to pass json format, but it's regained the
old 100M type format.
Memory leak fix from Pan Nengyuan
Virtiofs
fchmod seccomp fix from Max Reitz
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=KYWs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20200617a' into staging
Migration (and HMP and virtiofs) pull 2020-06-17
Migration:
HMP/migration and test changes from Mao Zhongyi
multifd fix from Laurent Vivier
HMP
qom-set partial reversion/change from David Hildenbrand
now you need -j to pass json format, but it's regained the
old 100M type format.
Memory leak fix from Pan Nengyuan
Virtiofs
fchmod seccomp fix from Max Reitz
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Wed 17 Jun 2020 19:34:58 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20200617a:
migration: fix multifd_send_pages() next channel
docs/xbzrle: update 'cache miss rate' and 'encoding rate' to docs
monitor/hmp-cmds: improvements for the 'info migrate'
monitor/hmp-cmds: add 'goto end' to reduce duplicate code.
monitor/hmp-cmds: delete redundant Error check before invoke hmp_handle_error()
monitor/hmp-cmds: don't silently output when running 'migrate_set_downtime' fails
monitor/hmp-cmds: add units for migrate_parameters
tests/migration: fix unreachable path in stress test
tests/migration: mem leak fix
hmp: Make json format optional for qom-set
qom-hmp-cmds: fix a memleak in hmp_qom_get
virtiofsd: Whitelist fchmod
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the "name" parameter is gone, there is hardly any difference
between NetLegacy and Netdev anymore, so we can drop NetLegacy and always
use Netdev to simplify the code quite a bit.
The only two differences that were really left between Netdev and NetLegacy:
1) NetLegacy does not allow a "hubport" type. We can continue to block
this with a simple check in net_client_init1() for this type.
2) The "id" parameter was optional in NetLegacy (and an internal id
was chosen via assign_name() during initialization), but it is mandatory
for Netdev. To avoid that the visitor code bails out here, we have to
add an internal id to the QemuOpts already earlier now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It's been deprecated since QEMU v3.1, so it's time to finally
remove it. The "id" parameter can simply be used instead.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The patch is to fix the "pkt" memory leak in packet_enqueue().
The allocated "pkt" needs to be freed if the colo compare
primary or secondary queue is too big.
Replace the error_report of full queue with a trace event.
Signed-off-by: Derek Su <dereksu@qnap.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In colo_compare_complete, insert CompareState into net_compares
only after everything has been initialized.
In colo_compare_finalize, remove CompareState from net_compares
before anything is deinitialized.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If the colo-compare object is removed before failover and a
checkpoint happens, qemu crashes because it tries to lock
the destroyed event_mtx in colo_notify_compares_event.
Fix this by checking if everything is initialized by
introducing a new variable colo_compare_active which
is protected by a new mutex colo_compare_mutex. The new mutex
also protects against concurrent access of the net_compares
list and makes sure that colo_notify_compares_event isn't
active while we destroy event_mtx and event_complete_cond.
With this it also is again possible to use colo without
colo-compare (periodic mode) and to use multiple colo-compare
for multiple network interfaces.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Else the log will be flooded if there is a lot of network
traffic.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The chr_out chardev is connected to a filter-redirector
running in the main loop. qemu_chr_fe_write_all might block
here in compare_chr_send if the (socket-)buffer is full.
If another filter-redirector in the main loop want's to
send data to chr_pri_in it might also block if the buffer
is full. This leads to a deadlock because both event loops
get blocked.
Fix this by converting compare_chr_send to a coroutine and
putting the packets in a send queue.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Tested-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
To be able to convert compare_chr_send to a coroutine in the
next commit, use qemu_co_sleep_ns if in coroutine.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
qemu_bh_new will set the bh to be executed in the main
loop. This causes crashes as colo_compare_handle_event assumes
that it has exclusive access the queues, which are also
concurrently accessed in the iothread.
Create the bh with the AioContext of the iothread to fulfill
these assumptions and fix the crashes. This is safe, because
the bh already takes the appropriate locks.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Derek Su <dereksu@qnap.com>
Tested-by: Derek Su <dereksu@qnap.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The sender of packet will be checked in the qemu_net_queue_purge() but
we use NetClientState not its peer when trying to purge the incoming
queue in qemu_flush_or_purge_packets(). This will trigger the assert
in virtio_net_reset since we can't pass the sender check:
hw/net/virtio-net.c:533: void virtio_net_reset(VirtIODevice *): Assertion
`!virtio_net_get_subqueue(nc)->async_tx.elem' failed.
#9 0x55a33fa31b78 in virtio_net_reset hw/net/virtio-net.c:533:13
#10 0x55a33fc88412 in virtio_reset hw/virtio/virtio.c:1919:9
#11 0x55a341d82764 in virtio_bus_reset hw/virtio/virtio-bus.c:95:9
#12 0x55a341dba2de in virtio_pci_reset hw/virtio/virtio-pci.c:1824:5
#13 0x55a341db3e02 in virtio_pci_common_write hw/virtio/virtio-pci.c:1252:13
#14 0x55a33f62117b in memory_region_write_accessor memory.c:496:5
#15 0x55a33f6205e4 in access_with_adjusted_size memory.c:557:18
#16 0x55a33f61e177 in memory_region_dispatch_write memory.c:1488:16
Reproducer:
https://www.mail-archive.com/qemu-devel@nongnu.org/msg701914.html
Fix by using the peer.
Reported-by: "Alexander Bulekov" <alxndr@bu.edu>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: ca77d85e1d ("net: complete all queued packets on VM stop")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Two defects are fixed:
1/ Detection of multicast frames
2/ Treating drop of mis-addressed frames as non-error
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
TX_LAST bit should not be set by hardware, its set by guest to inform
the last bd of the frame.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Mask all interrupt on reset.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Advertise support of clear-on-read for ISR registers.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a property "jumbo-max-len", which sets default value of jumbo frames
up to 16,383 bytes. Add Frame length checks for standard and jumbo
frames.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
