If the CMSDK APB timer is set up with a zero RELOAD value
then it will count down to zero, fire once and then stay
at zero. From the point of view of the ptimer system, the
timer is disabled; but the enable bit in the CTRL register
is still set and if the guest subsequently writes to the
RELOAD or VALUE registers this should cause the timer to
start counting down again.
Add code to the write paths for RELOAD and VALUE so that
we correctly restart the timer in this situation.
Conversely, if the new RELOAD and VALUE are both zero,
we should stop the ptimer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-5-peter.maydell@linaro.org
The CMSDK APB timer is currently always configured as periodic timer.
This results in the following messages when trying to boot Linux.
Timer with delta zero, disabling
If the timer limit set with the RELOAD command is 0, the timer
needs to be enabled as one-shot timer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CMSDK timer interrupt triggers when the counter goes from 1 to 0,
so we want to trigger immediately, rather than waiting for a
clock cycle. Drop the incorrect NO_IMMEDIATE_TRIGGER setting.
We also do not want to get an interrupt if the guest sets the
counter directly to zero, so use the new TRIGGER_ONLY_ON_DECREMENT
policy.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-3-peter.maydell@linaro.org
Basic emulation of the M41T80 serial (I2C) RTC chip. Only getting time
of day is implemented. Setting time and RTC alarm are not supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606152128.449-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When compiling with NVRAM_PRINTF enabled, gcc currently bails out with:
CC hw/timer/m48t59.o
CC hw/timer/m48t59-isa.o
hw/timer/m48t59.c: In function ‘NVRAM_writeb’:
hw/timer/m48t59.c:460:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘hwaddr’ [-Werror=format=]
NVRAM_PRINTF("%s: 0x%08x => 0x%08x\n", __func__, addr, val);
^
hw/timer/m48t59.c:460:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘uint64_t’ [-Werror=format=]
hw/timer/m48t59.c: In function ‘NVRAM_readb’:
hw/timer/m48t59.c:492:5: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘hwaddr’ [-Werror=format=]
NVRAM_PRINTF("%s: 0x%08x <= 0x%08x\n", __func__, addr, retval);
Fix it by using the correct format strings and while we're at it,
also change the definition of NVRAM_PRINTF so that this can not
bit-rot so easily again.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
commit 1d3e65aa7a ("hw/timer: Add value matching support to
aspeed_timer") increased the vmstate version of aspeed.timer because
the state had changed, but it also bumped the version of the
VMSTATE_STRUCT_ARRAY under the aspeed.timerctrl which did not need to.
Change back this version to fix migration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180423101433.17759-1-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
Allow the guest to determine the time set from the QEMU command line.
This includes adding a trace event to debug the new time.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial commit of the ZynqMP RTC device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HPET saves its state by calculating the current time and recovers timer
offset using this calculated value. But these calculations include
divisions and multiplications. Therefore the timer state cannot be recovered
precise enough.
This patch introduces saving of the original value of the offset to
preserve the determinism of the timer.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Maria Klimushenkova <maria.klimushenkova@ispras.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
--
v3: Added compat property for correct migration.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180103224208.30291-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
and remove the old i386/pc dependency
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Modelled System Timer in Microsemi's Smartfusion2 Soc.
Timer has two 32bit down counters and two interrupts.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't use the old_mmio struct in memory region ops.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-5-git-send-email-peter.maydell@linaro.org
Don't use the old_mmio in the memory region ops struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-4-git-send-email-peter.maydell@linaro.org
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
In some cases, the guest can observe the wrong ordering of UIP and
interrupts. This can happen if the VCPU exit is timed like this:
iothread VCPU
... wait for interrupt ...
t-100ns read register A
t wake up, take BQL
t+100ns update_in_progress
return false
return UIP=0
trigger interrupt
The interrupt is late; the VCPU expected the falling edge of UIP to
happen after the interrupt. update_in_progress is already trying to
cover this case by latching UIP if the timer is going to fire soon,
and the fix is documented in the commit message for commit 56038ef623
("RTC: Update the RTC clock only when reading it", 2012-09-10). It
cannot be tested with qtest, because its timing of interrupts vs. reads
is exact.
However, the implementation was incorrect because UIP cmos_ioport_read
cleared register A instead of leaving that to rtc_update_timer. Fixing
the implementation of cmos_ioport_read to match the commit message,
however, breaks the "uip-stuck" test case from the previous patch.
To fix it, skip update timer optimizations if UIP has been latched.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement a model of the simple timer device found in the CMSDK.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-5-git-send-email-peter.maydell@linaro.org
When a timer is enabled before a reload value is set, the controller
waits for a reload value to be set before starting decrementing. This
fix tries to cover that case by changing the timer expiry only when
a reload value is valid.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1496739312-32304-1-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove defines not used anywhere.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Statements under 'case' were in some places wrongly indented bringing
confusion and making the code less readable. Remove also few unneeded
blank lines. No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix checkpatch errors:
1. ERROR: spaces required around that '+' (ctx:VxV)
2. ERROR: spaces required around that '&' (ctx:VxV)
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It tests the accuracy of rtc periodic timer which is recently
improved & fixed by commit 7ffcb539a3 ("mc146818rtc: precisely count
the clock for periodic timer", 2017-05-19).
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170527025301.23499-1-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a function, rtc_policy_slew_deliver_irq(), which delivers
irq if LOST_TICK_POLICY_SLEW is used, as which is only supported on
x86, other platforms call it will trigger a assert
After that, we can move the x86 specific code to the common place
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-6-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the code purely depends on LOST_TICK_POLICY_SLEW, we can simply
drop '#ifdef TARGET_I386' as only x86 can enable this tick policy
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-5-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Any tick policy specified on other platforms rather on TARGET_I386
will fall back to LOST_TICK_POLICY_DISCARD silently, this patch makes
sure only TARGET_I386 can enable LOST_TICK_POLICY_SLEW
After that, we can enable LOST_TICK_POLICY_SLEW in the common code
which need not use '#ifdef TARGET_I386' to make these code be x86
specific anymore
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-4-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two issues in current code:
1) If the period is changed by re-configuring RegA, the coalesced
irq will be scaled to reflect the new period, however, it
calculates the new interrupt number like this:
s->irq_coalesced = (s->irq_coalesced * s->period) / period;
There are some clocks will be lost if they are not enough to
be squeezed to a single new period that will cause the VM clock
slower
In order to fix the issue, we calculate the interrupt window
based on the precise clock rather than period, then the clocks
lost during period is scaled can be compensated properly
2) If periodic_timer_update() is called due to RegA reconfiguration,
i.e, the period is updated, current time is not the start point
for the next periodic timer, instead, which should start from the
last interrupt, otherwise, the clock in VM will become slow
This patch takes the clocks from last interrupt to current clock
into account and compensates the clocks for the next interrupt,
especially if a complete interrupt was lost in this window, the
time can be caught up by LOST_TICK_POLICY_SLEW
Signed-off-by: Tai Yunfang <yunfangtai@tencent.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-3-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the timer is updated whenever RegA or RegB is written
even if the periodic timer related configuration is not changed
This patch optimizes it slightly to make the update happen only
if its period or enable-status is changed, also later patches are
depend on this optimization
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Message-Id: <20170510083259.3900-2-xiaoguangrong@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use sizeof instead of ARRAY_SIZE, fixing -Wmemset-elt-size with recent
GCC versions.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
rename slavio_timer_init1 to slavio_timer_init and assign
it to slavio_timer_info.instance_init, then we drop the
SysBusDeviceClass::init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
* assign DeviceClass::vmsd instead of using vmstate_register function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
hpet needs to be mapped and wired by the board code and won't
work with -device. Remove the user_creatable flag from the device
class.
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-18-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
commit 33cd52b5d7 unset
cannot_instantiate_with_device_add_yet in TYPE_SYSBUS, making all
sysbus devices appear on "-device help" and lack the "no-user"
flag in "info qdm".
To fix this, we can set user_creatable=false by default on
TYPE_SYS_BUS_DEVICE, but this requires setting
user_creatable=true explicitly on the sysbus devices that
actually work with -device.
Fortunately today we have just a few has_dynamic_sysbus=1
machines: virt, pc-q35-*, ppce500, and spapr.
virt, ppce500, and spapr have extra checks to ensure just a few
device types can be instantiated:
* virt supports only TYPE_VFIO_CALXEDA_XGMAC, TYPE_VFIO_AMD_XGBE.
* ppce500 supports only TYPE_ETSEC_COMMON.
* spapr supports only TYPE_SPAPR_PCI_HOST_BRIDGE.
This patch sets user_creatable=true explicitly on those 4 device
classes.
Now, the more complex cases:
pc-q35-*: q35 has no sysbus device whitelist yet (which is a
separate bug). We are in the process of fixing it and building a
sysbus whitelist on q35, but in the meantime we can fix the
"-device help" and "info qdm" bugs mentioned above. Also, despite
not being strictly necessary for fixing the q35 bug, reducing the
list of user_creatable=true devices will help us be more
confident when building the q35 whitelist.
xen: We also have a hack at xen_set_dynamic_sysbus(), that sets
has_dynamic_sysbus=true at runtime when using the Xen
accelerator. This hack is only used to allow xen-backend devices
to be dynamically plugged/unplugged.
This means today we can use -device with the following 22 device
types, that are the ones compiled into the qemu-system-x86_64 and
qemu-system-i386 binaries:
* allwinner-ahci
* amd-iommu
* cfi.pflash01
* esp
* fw_cfg_io
* fw_cfg_mem
* generic-sdhci
* hpet
* intel-iommu
* ioapic
* isabus-bridge
* kvmclock
* kvm-ioapic
* kvmvapic
* SUNW,fdtwo
* sysbus-ahci
* sysbus-fdc
* sysbus-ohci
* unimplemented-device
* virtio-mmio
* xen-backend
* xen-sysdev
This patch adds user_creatable=true explicitly to those devices,
temporarily, just to keep 100% compatibility with existing
behavior of q35. Subsequent patches will remove
user_creatable=true from the devices that are really not meant to
user-creatable on any machine, and remove the FIXME comment from
the ones that are really supposed to be user-creatable. This is
being done in separate patches because we still don't have an
obvious list of devices that will be whitelisted by q35, and I
would like to get each device reviewed individually.
Cc: Alexander Graf <agraf@suse.de>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-block@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: sstabellini@kernel.org
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-3-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[ehabkost: Small changes at sysbus_device_class_init() comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
qemu_log_mask() and error_report() are preferred over fprintf() for
logging errors. Also remove square brackets [] and additional new line
characters in printed messages.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170313184750.429-2-krzk@kernel.org
[PMM: wrapped long line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The i.MX timer device can be reset by writing to the SWR bit
of the CR register. This has to behave differently from hard
(power-on) reset because it does not reset all of the bits
in the CR register.
We were incorrectly implementing soft reset and hard reset
the same way, and in addition had a logic error which meant
that we were clearing the bits that soft-reset is supposed
to preserve and not touching the bits that soft-reset clears.
This was not correct behaviour for either kind of reset.
Separate out the soft reset and hard reset code paths, and
correct the handling of reset of the CR register so that it
is correct in both cases.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
[PMM: rephrased commit message, spacing on operators;
use bool rather than int for is_soft_reset]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a new function mips_gictimer_get_freq() which returns the
frequency at which a GIC timer will count. This will be useful for
boards which perform setup based upon this frequency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The m48t59 device supports both ISA and direct sysbus attached versions of
the device in the one .c file. This can be awkward for some embedded
machine types which need the sysbus M48T59, but don't want to pull in the
ISA bus code and its other dependencies.
Therefore, this patch splits out the code for the ISA attached M48T59 into
its own C file. It will be built when both CONFIG_M48T59 and
CONFIG_ISA_BUS are enabled.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This patch disables the update of the periodic timer of mc146818rtc
in record/replay mode. State of this timer is saved and therefore does
not need to be updated in record/replay mode.
Read of RTC breaks the replay because all rtc reads have to be the same
as in record mode.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071730.4572.41874.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the Altera timer model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-6-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
reset mc146818rtc device when RESET event happens.
Fix the problem:
1. Guest boot the second cpu, set CMOS_RESET_CODE 0x0a to protect selfboot;
2. VM being reset by others, hmp_system_reset;
3. seabios resume check the CMOS_RESET_CODE, if 0x0a, jump to the BDA
resume execution by jump via 40h:0067h;
4. Guest halt;
Signed-off-by: hangaohuai <hangaohuai@huawei.com>
Message-Id: <20161219060336.10176-1-hangaohuai@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a NULL check for i2c slave init callbacks, so that we no longer
need to implement empty init functions.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20161202054617.6749-4-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: squashed in later tweak from Alistair to if() phrasing]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The STM32F2XX Timer emulator uses a 16 bit prescaler value to
limit the timer clock rate. It does that by dividing the timer
frequency. If the prescaler 's->tim_psc' was set to be UINT_MAX,
it'd lead to divide by zero error. Limit prescaler value to 16
bits to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476800269-31902-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM A9MP processor has a peripheral timer with an auto-increment
register, which holds an increment step value. A user could set
this value to zero. When auto-increment control bit is enabled,
it leads to an infinite loop in 'a9_gtimer_update' while
updating comparator value. Remove this loop incrementing the
comparator value.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476733226-11635-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If correctly configured allow the STM32F2xx timer to print
out the PWM duty cycle information.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: cdb59039a25e061615713a94b40797baa12ea9f9.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu tracks guest time based on vector [base_rtc, last_update], in which
last_update stands for a monotonic tick which is actually uptime of the
host.
according to rtc implementation codes of recent releases and upstream,
after
migration, the time base vector [base_rtc, last_update] isn't updated to
coordinate with the destionation host, ie. qemu doesnt update last_update
to
uptime of the destination host.
what problem have we got because of this bug? after migration, guest time
may
jump back to several days ago, that will make some critical business
applications,
such as lotus notes, malfunction.
this patch is trying to fix the problem. first, when vmsave in progress,
we
rtc_update_time to refresh time stamp in cmos array, then during
vmrestore,
we rtc_set_time to update qemu base_rtc and last_update variable according
to time
stamp in cmos array.
Signed-off-by: Junlian Bell <zhongjun@sangfor.com.cn>
Message-Id: <20160926124101.2364-1-zhongjun@sangfor.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'char const' means the same thing as 'const char', but we
use the former in only a handful of places and we use the
latter over six thousand times. Switch the imx reg_name()
functions to bring them in line with everything else.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of the timer devices may behave differently from what ptimer
provides. Introduce ptimer policy feature that allows ptimer users to
change default and wrong timer behaviour, for example to continuously
trigger periodic timer when load value is equal to "0".
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 994cd608ec392da6e58f0643800dda595edb9d97.1473252818.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interval timer is similar to the CP0 Count/Compare timer within
each processor. The difference is the GIC_SH_COUNTER register is global
to the system so that all processors have the same time reference.
To ease implementation, all VPs are having its own QEMU timer but sharing
global settings and registers such as GIC_SH_CONFIG.COUTNSTOP and
GIC_SH_COUNTER.
MIPS GIC Interval Timer does support upto 64 bits of Count register but
in this implementation it is limited to 32 bits only.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In various Freescale SOCs, the GPT timers can be configured to select
its input clock.
Depending on the SOC the set of available input clocks may vary.
The actual single GPT definition was no good enough and because of it
booting the sabrelite board with a i.MX6DL device tree would fail
because of an incorrect input clock definition for the i.MX6DL SOC.
This patch fixes the i.MX6DL boot failure by adding the ability to
define a different set of input clocks depending on the considered SOC.
A different class has been defined for i.MX25, i.MX31 and i.MX6 each with
its specific set of input clocks.
The patch has been tested by booting KZM, i.MX25 PDK, i.MX6Q sabrelite
and i.MX6DL sabrelite.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 1467325619-8374-1-git-send-email-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed spacing round '/' operator]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MC146818 RTC device has output IRQ line. Currently the corresponding field
is only accessible through direct access. Such access violates Qemu model.
The patch makes the field accessible through GPIO. It also updates the setting
of the IRQ during initialization.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/timer/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-20-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old milkymist.org domain just forwards to mm-labs.hk nowadays. I've
created a mirror of the documents.
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Value matching allows Linux to boot with CONFIG_NO_HZ_IDLE=y on the
palmetto-bmc machine. Two match registers are provided for each timer.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1465974248-20434-1-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64() is "uint64_t muldiv64(uint64_t a, uint32_t b, uint32_t c)"
Some time it is used as muldiv64(uint32_t a, uint64_t b, uint32_t c)"
This patch is the result of coccinelle script
scripts/coccinelle/swap_muldiv64.cocci to reorder arguments.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is not visible with the default "log" trace backend. With other
backends however trace.h does not include qemu/log.h, resulting in
build failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1463745452-25831-2-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 0d63b2dd31.
This change was originally intended to correct the HPET behavior
in conjunction with Linux, however the behavior that it actually creates
is not compatible with the ioapic.c implementation; it used to be
compatible with KVM's own IOAPIC but it is not anymore.
Signed-off-by: Bill Paul <wpaul@windriver.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <201604051558.20070.wpaul@windriver.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement basic ASPEED timer functionality for the AST2400 SoC[1]: Up to
8 timers can independently be configured, enabled, reset and disabled.
Some hardware features are not implemented, namely clock value matching
and pulse generation, but the implementation is enough to boot the Linux
kernel configured with aspeed_defconfig.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
EPIT, GPT and other i.MX timers are using "abstract" clocks among which
a CLK_IPG_HIGH clock.
On i.MX25 and i.MX31 CLK_IPG and CLK_IPG_HIGH are mapped to the same clock
but on other SOC like i.MX6 they are mapped to distinct clocks.
This patch add the CLK_IPG_HIGH to prepare for SOC where these 2 clocks are
different.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 224bf650194760284cb40630e985867e1373276a.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This way all CCM clock defines/enums are named CLK_XXX
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 8537df765c1713625c7a8b9aca4c7ca60b42e0c0.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPT timer need to rollover when it reaches 0xffffffff.
It also need to reset to 0 when in "restart mode" and crossing the
compare 1 register.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 6e2b36117a249a78bf822dd59a390368f407136e.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TUSB6010 is a USB controller (as the name suggests). Move it from
hw/timer (where it was accidentally filed in 2013 when we moved
everything out of hw/) to hw/usb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455883404-10976-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign pl031_init to pl031_info.instance_init and drop the
SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_rtc_init to exynos4210_rtc_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_pwm_init to exynos4210_pwm_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign exynos4210_mct_init to exynos4210_mct_info.instance_init
and drop the SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign DeviceClass::vmsd instead of using vmstate_register function
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* assign icp_pit_init to icp_pit_info.instance_init
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split the bits that require it to exec/log.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1452174932-28657-8-git-send-email-den@openvz.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-26-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-9-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-7-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
Device realize() methods aren't supposed to call hw_error(), they
should set an error and fail cleanly. Do that.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-4-git-send-email-armbru@redhat.com>
This is to prepare for CCM code refactoring.
This is just a bit of function and enum values renaming.
We also remove some useless intermediate variables.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 53c4d9b9611988a5f56f178f285e04490747925e.1449528242.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed integer overflow in C is undefined behaviour, and the compiler
is at liberty to assume it can never happen and optimize accordingly.
In particular, the subtractions in hpet_time_after() and hpet_time_after64()
were causing OSX clang to optimize the code such that it was prone to
hangs and complaints about the main loop stalling (presumably because
we were spending all our time trying to service very high frequency
HPET timer callbacks). The clang sanitizer confirms the UB:
hw/timer/hpet.c:119:26: runtime error: signed integer overflow: -2146967296 - 2147003978 cannot be represented in type 'int'
Fix this by doing the subtraction as an unsigned operation and then
converting to signed for the comparison.
Reported-by: Aaron Elkins <threcius@yahoo.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1447080991-24995-1-git-send-email-peter.maydell@linaro.org
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: b7ce7e98a051479453744aded122789531d80a44.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 5bbad71517ca728d8865f7b9f998baa0df022794.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hpet defines a clock period in femtoseconds but
then converts it to nanoseconds to use the internal
timers.
We can define the period in nanoseconds and use it
directly, this allows to remove muldiv64().
We only need to convert the period to femtoseconds
to put it in internal hpet capability register.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the KZM board to use the i.MX31 SoC defintition instead of
redefining the entire SoC on the machine level. Major rewrite of the
machine init code.
While touching the memory map comment de-indent to the correct level
of indentation.
This obsoletes the legacy i.MX device device creation helpers which are removed.
Tested by booting a minimal Linux system on the emulated platform
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 5e783561f092e1c939562fdff001f1ab1194b07f.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit e0cf11f31c ("timer: Use a single
definition of NSEC_PER_SEC for the whole codebase") renamed
NANOSECONDS_PER_SECOND to NSEC_PER_SEC.
On Mac OS X there is a <dispatch/time.h> system header which also
defines NSEC_PER_SEC. This causes compiler warnings.
Let's use the old name instead. It's longer but it doesn't clash.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436364609-7929-1-git-send-email-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timer should fire the interrupt only if the IT (interrupt enable) bit
state of the control register is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The running timer can't be stopped because timer control code just
doesn't handle disabling the timer. Fix it by deleting the timer if
the enable bit is cleared.
The timer won't start periodic ticking if a ONE-SHOT -> PERIODIC mode
change happens after a one-shot tick was completed. Fix it by
re-starting ticking if the timer isn't ticking right now.
To avoid code churning, these two fixes are squashed in one commit.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interval interrupt is not set if the timer is in decrement mode.
This is because x >=0 and x < interval after leaving the while-loop.
Signed-off-by: Johannes Schlatow <schlatow@ida.ing.tu-bs.de>
Message-id: 20150630135821.51f3b4fd@johanness-latitude
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When loading a VM from a snapshot or migration, clock changes can cause
the periodic timer to stall or loop rapidly.
qemu-timer has a reset notifier mechanism that is used to avoid timer
stalls or loops if the host clock changes while the VM is running when
using QEMU_CLOCK_HOST. However, when loading a snapshot or migration,
qemu-timer is initialized and fires the reset notifier before
mc146818rtc is initialized and has registered its reset handler. In
addition, this mechanism isn't used when using QEMU_CLOCK_REALTIME,
which might also change when loading a snapshot or migration.
To correct that problem, this commit resets the periodic timer after
loading from a snapshot or migration if the clock has either jumped
backward or has jumped forward by more than the clock jump limit that
is used by the reset notifier code in qemu-timer.
Signed-off-by: Paul Donohue <qemu-git@PaulSD.com>
Message-Id: <20150612141013.GE2749@TopQuark.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Due converting PIO to the new memory read/write api we no longer provide
separate I/O region lenghts for read and write operations. As a result,
reading from PIT Mode/Command register will end with accessing
pit->channels with invalid index.
Fix this by ignoring read from the Mode/Command register.
This is CVE-2015-3214.
Reported-by: Matt Tait <matttait@google.com>
Fixes: 0505bcdec8
Cc: qemu-stable@nongnu.org
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
Switch all the uses of ld/st*_phys to address_space_ld/st*,
except for those cases where the address space is the CPU's
(ie cs->as). This was done with the following script which
generates a Coccinelle patch.
A few over-80-columns lines in the result were rewrapped by
hand where Coccinelle failed to do the wrapping automatically,
as well as one location where it didn't put a line-continuation
'\' when wrapping lines on a change made to a match inside
a macro definition.
===begin===
#!/bin/sh -e
# Usage:
# ./ldst-phys.spatch.sh > ldst-phys.spatch
# spatch -sp_file ldst-phys.spatch -dir . | sed -e '/^+/s/\t/ /g' > out.patch
# patch -p1 < out.patch
for FN in ub uw_le uw_be l_le l_be q_le q_be uw l q; do
cat <<EOF
@ cpu_matches_ld_${FN} @
expression E1,E2;
identifier as;
@@
ld${FN}_phys(E1->as,E2)
@ other_matches_ld_${FN} depends on !cpu_matches_ld_${FN} @
expression E1,E2;
@@
-ld${FN}_phys(E1,E2)
+address_space_ld${FN}(E1,E2, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
for FN in b w_le w_be l_le l_be q_le q_be w l q; do
cat <<EOF
@ cpu_matches_st_${FN} @
expression E1,E2,E3;
identifier as;
@@
st${FN}_phys(E1->as,E2,E3)
@ other_matches_st_${FN} depends on !cpu_matches_st_${FN} @
expression E1,E2,E3;
@@
-st${FN}_phys(E1,E2,E3)
+address_space_st${FN}(E1,E2,E3, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
===endit===
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
This patch adds the stm32f2xx timers: TIM2, TIM3, TIM4 and TIM5
to QEMU.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 155091a323390f8da3cca496e4c611c493e62a77.1424175342.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJU/vQnAAoJEFvCxW+uDzIfSHQIAKLVePJyOEtVA5OOUSyuA5TQ
6MNXg1X+PxD0GT8iyKhcyHqaRSibPjY/D2Hb8MyNt/lLIQj13hfL1fXXAMvnjY1+
WcCpGfbZmmcIpgjY+OWkkSVU3nSxNE6a0ZgdOvK9Cvc+dJHMpO02E5kRqig6nYX6
UuA7aIgjE2T63PPucuEjFVA4a8v7NsqO4OBmYPO/L7KEpAQk3Y/qDDGahQRXuBXl
0poyJrj99BoKHJFemf7L79SbpZHrnaQ54dndqerq5tzmBXRVjhYJa/iLm0LSjPnN
kWdlMKXSGgI/rFRWZqfOk+jDIZb21xliM6y/lDpDJGdoC1aPsIWwQ0mFK6ZPVDo=
=Ee+Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-signed' into staging
qemu-sparc update
# gpg: Signature made Tue Mar 10 13:39:51 2015 GMT using RSA key ID AE0F321F
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>"
* remotes/mcayland/tags/qemu-sparc-signed:
sun4u: switch m48t59 NVRAM to MMIO access
MAINTAINERS: add myself as SPARC maintainer
doc: minor updates to SPARC32 and SPARC64 documentation
m48t59: add m48t59 sysbus device
m48t59: introduce new base-year qdev property
m48t59: let init functions return a Nvram object
m48t59: add a Nvram interface
m48t59: register a QOM type for each nvram type we support
m48t59: move ISA ports/memory regions registration to QOM constructor
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is for subsequent use by the sun4u machine.
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently the m48t59 device uses the hardware model in order to determine
whether the year value is offset from the hardware value. As this will
soon be required by the x59 model, create a qdev base-year property to
represent the base year and update the callers appropriately.
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
CC: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Remove left-overs from header file.
Move some functions only used by PReP to hw/ppc/prep.c
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
CC: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
