The link property that was added to the pcspk device has the wrong type:
it is only correct for TCG and for KVM's userspace or split irqchip
options. The default KVM option (fully in-kernel irqchip) breaks
because it uses a PIT whose type is a sibling of TYPE_I8254.
Fixes: 873b4d3f05
Tested-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1467298657-6588-1-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Otherwise, a serial port can get stuck if it is migrated while flow control
is in effect.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise, this can cause serial_xmit to be entered with LSR.TEMT=0,
which is invalid and causes an assertion failure.
Reported-by: Bret Ketchum <bcketchum@gmail.com>
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
g_source_attach can return any value between 1 and UINT_MAX if you let
QEMU run long enough. However, qemu_chr_fe_add_watch can also return
a negative errno value when the device is disconnected or does not
support chr_add_watch. Change it to return zero to avoid overloading
these values.
Fix the cadence_uart which asserts in this case (easily obtained with
"-serial pty").
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
serial_xmit starts transmission of whatever is in the transmitter
register, THR or FIFO; serial_watch_cb is a wrapper around it and is
only used as a qemu_chr_fe_add_watch callback.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move common code outside the if, and reset tsr_retry even in loopback mode.
Right now it cannot become non-zero, but it will be possible as soon as
we start respecting the baud rate.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It can never become negative; reflect this in the type of the field
and simplify the conditions.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In function pci_assign_dev_load_option_rom, For those pci devices don't
have 'rom' file under sysfs or if loading ROM from external file, The
function returns NULL, and won't set the passed 'size' variable.
In these 2 cases, qemu still reports "Invalid ROM" error message, Users
may be confused by it.
Signed-off-by: Lin Ma <lma@suse.com>
Message-Id: <1466010327-22368-1-git-send-email-lma@suse.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 926cde5 ("scsi: esp: make cmdbuf big enough for maximum CDB size",
2016-06-16) changed the size of a migrated field. Split it in two
parts, and only migrate the second part in a new vmstate version.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MC146818 RTC device has output IRQ line. Currently the corresponding field
is only accessible through direct access. Such access violates Qemu model.
The patch makes the field accessible through GPIO. It also updates the setting
of the IRQ during initialization.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently a direct access to the device structure field is used to connect ISA
device IRQ to the bus. GPIO access should be used instead if possible.
The patch adds wrapper isa_connect_gpio_out. The function connects specified
output GPIO to specified ISA IRQ.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The isa_bus_irqs function initializes ISA bus IRQ array pointer with specified
value.
Previously the ICH9 LPC bridge model did not have its own IRQs but
only IRQ pointer cache. And same GSI were used for ISA bus and other sources
behind the bridge (PCI, SCI). Hence, the pc_q35_init was only possible place to
setup both ISA bus IRQs and the bridge IRQ cache.
As a result, the call of isa_bus_irqs was made from pc_q35_init.
Now the ICH9 LPC bridge has its own output IRQs which are connected to GSI. The
output IRQs are already used to route IRQs from PCI and SCI.
The patch makes the ICH9 LPC bridge output IRQs to used for ISA bus too.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ICH9 LPC bridge has 24 output IRQs connected to GSI. Currently the IRQs are
referenced by pointers. The pointers are initialized at startup by direct access
to the structure fields. This violates Qemu device model.
The patch makes the IRQs handling to use GPIO model.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ich9->pic and ich9->ioapic differ for the first 16 GSIs (because
ich9->pic is wired to 8259+IOAPIC but ich9->ioapic is wired to
IOAPIC only). However, ich9->ioapic is never used for the first
16 GSIs, so the two vectors can be merged.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ich9_lpc_update_pic take care only of GSIs 0-15, and
ich9_lpc_update_apic take care only of GSIs 16-23. Assert
that they are called with the correct GSI indices.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An asserted pirq can be disabled and the corresponding GSIs
should then go down to 0. However, because of the conditional in
ich9_lpc_update_by_pirq, the legacy 8259 pin could remain stuck to 1.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ICH9 SMB bridge can be created using qdev API despite existence of helper
function. The type name is needed for such creation. Using a preprocessor
alias instead the string type name itself is preferable.
The patch makes the alias accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The port92 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The
pointer is never changed at runtime. Hence, common GPIO model can be applied
to A20 IRQ line. Note that checking for IRQ to be connected as in
previous version of code is not required qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i8042 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The pointer
is never changed at runtime. So common GPIO model can be applied to A20 IRQ
line. Note that checking for IRQ to be connected as in previous version
of code is not required because qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, Q35 instance is configured using direct access to structure fields.
The patch uses property interface to set the fields.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During creation of Q35 instance several parameters are set using direct access.
It violates Qemu device model. Correctly, the parameters should be handled as
object properties.
The patch adds four link type properties for fields:
mch.ram_memory
mch.pci_address_space
mch.system_memory
mch.address_space_io
And, it adds two size type properties for fields:
mch.below_4g_mem_size
mch.above_4g_mem_size
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev API can be used to create CFI pflash devices despite existance of helper
functions. The type name is needed in course of such creation. Using the
preprocessor alias instead of the string literal itself is preferable.
The patch makes the aliases accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently vmport device is identified by the string literal. Using a
preprocessor alias instead is preferable.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The speaker device needs pointer to ISA PIT device to operate. But according to
qdev-properties.h, properties of pointer type should be avoided. It seems a
link type property is a good substitution.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use ldl_le_p() and stl_le_p() instead of le32_to_cpup() and
cpu_to_le32w(); the former handle misaligned addresses and don't
need casts, and the latter are deprecated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 1465575021-3774-1-git-send-email-peter.maydell@linaro.org
Multiqueue virtio-blk can be enabled as follows:
qemu -device virtio-blk-pci,num-queues=8
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-8-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Monitor ioeventfds for all virtqueues in the device's AioContext. This
is not true multiqueue because requests from all virtqueues are
processed in a single IOThread. In the future it will be possible to
use multiple IOThreads when the QEMU block layer supports multiqueue.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-7-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a field for the virtqueue index when migrating the s->rq request
list. The new field is only needed when num_queues > 1. Existing QEMUs
are unaffected by this change and therefore virtio-blk migration stays
compatible.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-6-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Multiqueue requires that each request knows to which virtqueue it
belongs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-5-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Let the virtio_blk_data_plane_notify() caller decide which virtqueue to
notify. This will allow the function to be used with multiqueue.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-4-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The batch notification BH needs to know which virtqueues to notify when
multiqueue is enabled. Use a bitmap to track the virtqueues with
pending notifications.
At this point there is only one virtqueue so hard-code virtqueue index
0. A later patch will switch to real virtqueue indices.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-3-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The num_queues field is always 1 for the time being. A later patch will
make it a configurable device property so that multiqueue can be
enabled.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-2-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit 10a06fd65f.
Dataplane has used the same virtqueue code as non-dataplane since
commits e24a47c5b7 ("virtio-scsi: do not
use vring in dataplane") and 03de2f5274
("virtio-blk: do not use vring in dataplane"). It is no longer
necessary to stop dataplane in order to sync state since there is no
duplicated virtqueue state.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-id: 1466503331-9831-1-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXce8xAAoJEO8Ells5jWIRorwH/3Q+fHmkSBlPGOna9zOs4zrB
SB6/aa9Yw2UXCZJgCIh/5Ci09/lCJGVEkX7pkYEBuTwW3PceYWPQJAWpzDlmG0ch
U1xaVNuCubmMoVfD/4BEWQR3SdJ0VGVnunhWkAB4sh/PKb7csVv9DdwIDvfD7ZsF
1hGNvybxWu3RMaX2HxQKCrp9QdGaFAfkGivQCq+NACckytEdBZJVPMc5Qc4y/4S6
HOGBMYLYwp5vhJi1sZjnwB2otyZS4yxVkPlR2EexaOpWrqpOFDLiYpPWVINWLWM+
C/NV4qZfb3kU8zaIQCKuTPPmq/N7CrC1uPen3AhhSgpxrlA+nZ8af1tOruhoHA4=
=8N5c
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 28 Jun 2016 04:29:53 BST
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
vmxnet3: Fix reading/writing guest memory specially when behind an IOMMU
rtl8139: save/load RxMulOk counter (again)
Change net/socket.c to use socket_*() functions
net: mipsnet: check transmit buffer size before sending
net: fix qemu_announce_self not emitting packets
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing configurations error out currently as follows:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c: In function ‘aspeed_scu_read’:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:9: error: implicit declaration of function ‘qemu_log_mask’ [-Werror=implicit-function-declaration]
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:9: error: nested extern declaration of ‘qemu_log_mask’ [-Werror=nested-externs]
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:23: error: ‘LOG_GUEST_ERROR’ undeclared (first use in this function)
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:130:23: note: each undeclared identifier is reported only once for each function it appears in
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c: In function ‘aspeed_scu_write’:
/home/travis/build/pranith/qemu/hw/misc/aspeed_scu.c:154:23: error: ‘LOG_GUEST_ERROR’ undeclared (first use in this function)
This is caused by a missing header file. Fix it.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20160627215304.821-1-bobby.prani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a PCI device lives behind an IOMMU, it should use 'pci_dma_*' family of
functions when any transfer from/to guest memory is required while
'cpu_physical_memory_*' family of functions completely bypass any MMU/IOMMU in
the system.
vmxnet3 in some places was using 'cpu_physical_memory_*' family of functions
which works fine with the default QEMU setup where IOMMU is not enabled but
fails miserably when IOMMU is enabled. This commit converts all such instances
in favor of 'pci_dma_*'
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Commit 9d29cdeaac (rtl8139: port
TallyCounters to vmstate) introduced in incompatibility in the v4
format as it omitted the RxOkMul counter.
There are presumably no users that were impacted by the v4 to v4'
breakage, so increase the save version to 5 and re-add the field,
keeping backward compatibility with v4'.
We can't have a field conditional on the section version in
vmstate_tally_counters since this version checked would not be the
section version (but the version defined in this structure). So, move
all the fields into the main state structure.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When processing MIPSnet I/O port write operation, it uses a
transmit buffer tx_buffer[MAX_ETH_FRAME_SIZE=1514]. Two indices
's->tx_written' and 's->tx_count' are used to control data written
to this buffer. If the two were to be equal before writing, it'd
lead to an OOB write access beyond tx_buffer. Add check to avoid it.
Reported-by: Li Qiang <qiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We only care about the associated backend, so blk_drain is more
appropriate here.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20160612065603.21911-1-famz@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-6-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-5-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-4-git-send-email-peter.maydell@linaro.org
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-3-git-send-email-peter.maydell@linaro.org
Don't use cpu_to_*w() and *_to_cpup() to do byte-swapped loads
and stores; instead use ld*_p() and st*_p() which correctly handle
misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-2-git-send-email-peter.maydell@linaro.org
This commit fix obvious bug in WINBOND command handling.
Datasheet states that default dummy cycles is 8 so fix it.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Message-id: 1466755631-25201-11-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
