Both virtio-blk and virtio-scsi use virtio_queue_empty() as the
loop condition in VQ handlers (virtio_blk_handle_vq,
virtio_scsi_handle_cmd_vq). When a device is marked broken in
virtqueue_pop, for example if a vIOMMU address translation failed, we
want to break out of the loop.
This fixes a hanging problem when booting a CentOS 3.10.0-862.el7.x86_64
kernel with ATS enabled:
$ qemu-system-x86_64 \
... \
-device intel-iommu,intremap=on,caching-mode=on,eim=on,device-iotlb=on \
-device virtio-scsi-pci,iommu_platform=on,ats=on,id=scsi0,bus=pci.4,addr=0x0
The dead loop happens immediately when the kernel boots and initializes
the device, where virtio_scsi_data_plane_handle_cmd will not return:
> ...
> #13 0x00005586602b7793 in virtio_scsi_handle_cmd_vq
> #14 0x00005586602b8d66 in virtio_scsi_data_plane_handle_cmd
> #15 0x00005586602ddab7 in virtio_queue_notify_aio_vq
> #16 0x00005586602dfc9f in virtio_queue_host_notifier_aio_poll
> #17 0x00005586607885da in run_poll_handlers_once
> #18 0x000055866078880e in try_poll_mode
> #19 0x00005586607888eb in aio_poll
> #20 0x0000558660784561 in aio_wait_bh_oneshot
> #21 0x00005586602b9582 in virtio_scsi_dataplane_stop
> #22 0x00005586605a7110 in virtio_bus_stop_ioeventfd
> #23 0x00005586605a9426 in virtio_pci_stop_ioeventfd
> #24 0x00005586605ab808 in virtio_pci_common_write
> #25 0x0000558660242396 in memory_region_write_accessor
> #26 0x00005586602425ab in access_with_adjusted_size
> #27 0x0000558660245281 in memory_region_dispatch_write
> #28 0x00005586601e008e in flatview_write_continue
> #29 0x00005586601e01d8 in flatview_write
> #30 0x00005586601e04de in address_space_write
> #31 0x00005586601e052f in address_space_rw
> #32 0x00005586602607f2 in kvm_cpu_exec
> #33 0x0000558660227148 in qemu_kvm_cpu_thread_fn
> #34 0x000055866078bde7 in qemu_thread_start
> #35 0x00007f5784906594 in start_thread
> #36 0x00007f5784639e6f in clone
With this patch, virtio_queue_empty will now return 1 as soon as the
vdev is marked as broken, after a "virtio: zero sized buffers are not
allowed" error.
To be consistent, update virtio_queue_empty_rcu as well.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180910145616.8598-2-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
USB frame rate is slightly lower than 1kHz: ie. ~950Hz.
Thus usb-audio device is not able to perform a simple audio playback
without underruns on audio backend.
eg. "-device pci-ohci,id=ohci -device usb-audio,bus=ohci.0" vs PulseAudio
backend. more than 50 underruns are observed per second.
Update ohci_sof_time computation, using QEMU_CLOCK_VIRTUAL in
ohci_usb_start(), and increment by usb_frame_time in ohci_sof()
makes USB frame rate close to 1kHz.
This way, no audio underrun are observed during audio playback.
Signed-off-by: Miguel GAIO <mgaio35@gmail.com>
Message-Id: <20180927151936.3647-1-mgaio35@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Stale values in this field may result in qemu
expecting more data on the next operation
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180907220851.9658-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Return STORE_FULL if we can't write all the bytes but
return incomplete transfer if data received is less then
what was specified in the metadata. Also, use d->offset
as the file size which is valid for all file sizes.
Signed-off-by: Bandan <bsd@redhat.com>
Message-id: 20180907220851.9658-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Monochrome cursors are still used by Windows guests with the
QXL-WDDM-DOD driver. Such cursor types have one odd feature, inversion
of colors. GDK does not seem to support it, so implement an alternative
solution: fill the inverted pixels and add an outline to make the cursor
more visible. Tested with the text cursor in Notepad and Windows 10.
cursor_set_mono is also used by the vmware GPU, so add a special check
to avoid breaking its 32bpp format (tested with Kubuntu 14.04.4). I was
unable to find a guest which supports the 1bpp format with a vmware GPU.
The old implementation was buggy and removed in v2.10.0-108-g79c5a10cdd
("qxl: drop mono cursor support"), this version improves upon that by
adding bounds validation, clarifying the semantics of the two masks and
adds a workaround for inverted colors support.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1611984
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Message-id: 20180903145447.17142-1-peter@lekensteyn.nl
[ kraxel: minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing monitor config from guest store head0 width and height
for single-head configurations. Use these when creating the
DisplaySurface in the local renderer.
This fixes a rendering issue with wayland. Wayland rounds up the
framebuffer width and height to a multiple of 64, so with odd
resolutions (800x600 for example) the framebuffer is larger than the
actual screen. The monitor config has the actual screen size though.
This fixes guest display for anything using the local renderer
(non-spice UI, screendump monitor command).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180919103057.9666-1-kraxel@redhat.com
This patch adds edid support to the qemu stdvga. It is turned off by
default and can be enabled with the new edid property. The patch also
adds xres and yres properties to specify the video mode you want the
guest use. Works only with edid enabled and updated guest driver.
The mmio bar of the stdvga has some unused address space at the start.
It was reserved just in case it'll be needed for virtio, but it turned
out to not be needed for that. So let's use that region to place the
EDID data block there.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-6-kraxel@redhat.com
Create a io region for an EDID data block.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180925075646.25114-4-kraxel@redhat.com
Helper function to figure the size of a edid blob, by checking how many
extensions are present. Both the base edid blob and the extensions are
128 bytes in size.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-3-kraxel@redhat.com
EDID is a metadata format to describe monitors. On physical hardware
the monitor has an eeprom with that data block which can be read over
i2c bus.
On a linux system you can usually find the EDID data block in
/sys/class/drm/$card/$connector/edid. xorg ships a edid-decode utility
which you can use to turn the blob into readable form.
I think it would be a good idea to use EDID for virtual displays too.
Needs changes in both qemu and guest kms drivers. This patch is the
first step, it adds an generator for EDID blobs to qemu. Comes with a
qemu-edid test tool included.
With EDID we can pass more information to the guest. Names and serial
numbers, so the guests display configuration has no boring "Unknown
Monitor". List of video modes. Display resolution, pretty important
in case we want add HiDPI support some day.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-2-kraxel@redhat.com
- Deprecate the "enforce-config-section" machine parameter
- Re-enable the wdt_ib700, endianness and vmxnet3 qtests
- Some trivial fixes and doc update patches that crossed my way
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dXgp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2018-09-25' into staging
- Deprecate the usage of a network backend via "name" instead of "id"
- Deprecate the "enforce-config-section" machine parameter
- Re-enable the wdt_ib700, endianness and vmxnet3 qtests
- Some trivial fixes and doc update patches that crossed my way
# gpg: Signature made Tue 25 Sep 2018 16:58:42 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>"
# gpg: aka "Thomas Huth <thuth@redhat.com>"
# gpg: aka "Thomas Huth <huth@tuxfamily.org>"
# gpg: aka "Thomas Huth <th.huth@posteo.de>"
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2018-09-25:
Revert "check: Move VMXNET3 test to common"
Revert "check: Move endianess test to common"
Revert "check: Move wdt_ib700 test to common"
tests/migration: Speed up the test on ppc64
hw/qdev-core: Fix description of instance_init
qdev: fix a typo in comment
docs: Fix some typos (most found by codespell)
trivial: Make bios files and source files non-executable
memfd: fix possible usage of the uninitialized file descriptor
hw/core/machine: Officially deprecate the enforce-config-section parameter
net/slirp: Deprecate the [hub_id name] parameter tuple
net: Deprecate the "name" parameter of -net
Makefile: Add missing dependency for qemu-deprecated.texi
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 16f7244842 added this parameter
to the documentation, including a note that it is deprecated. But it
has never been added to the "Deprecated features" appendix, which is
our official way to deprecate legacy parameters. So let's do this now.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code looks better, it removes duplicated lines and it will ease
the introduction of common properties for the Aspeed machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 evb is shipped with a W25Q256 which has a non volatile bit
to make the chip operate in 4 Byte address mode at power up. This
should be an interesting feature to model as it will exercise a bit
more the SMC controllers and MMIO execution at boot time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180921161939.822-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In file included from /home/thuth/devel/qemu/hw/timer/aspeed_timer.c:16:
/home/thuth/devel/qemu/include/hw/misc/aspeed_scu.h:37:3: error:
redefinition of typedef 'AspeedSCUState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
} AspeedSCUState;
^
/home/thuth/devel/qemu/include/hw/timer/aspeed_timer.h:27:31: note:
previous definition is here
typedef struct AspeedSCUState AspeedSCUState;
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 'break' statements missing from a switch in the APB dual-timer
write function. Spotted by Coverity as CID 1395626 and 1395633.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180924123122.14549-1-peter.maydell@linaro.org
The only difference between our implementation of the pcnet ioport
accessors and the mmio accessors is that the former check BCR_DWIO to
see what access widths are permitted for addresses in the aprom range
(0x0..0xf). In fact our failure to do this in the mmio accessors
is a bug (one which was fixed for the ioport accessors in
commit 7ba7974197 in 2011).
The data sheet for the Am79C970A does not describe the DWIO
bit as only applying for I/O space mapped I/O resources and
not memory mapped I/O resources, and our MMIO accessors already
honour DWIO for accesses in the 0x10..0x1f range (since the
pcnet_ioport_{read,write}{w,l} functions check it).
The data sheet for the later but compatible Am79C976 is clearer:
it states specifically "DWIO mode applies to both I/O- and
memory-mapped acceses." This seems to be reasonable evidence
in favour of interpretating the Am79C970A spec as being the same.
(NB: Linux's pcnet driver only supports I/O accesses, so the
MMIO access part of this device is probably untested anyway.)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the pcnet-pci device away from using the old_mmio
MemoryRegionOps accessor functions.
This commit is a no-behaviour-change API conversion.
(Since PCNET_PNPMMIO_SIZE is 0x20, the old "addr & 0x10"
check and the new "addr < 0x10" check are exact opposites;
the new code is phrased to be parallel with the
pcnet_io_read/write functions.)
I have left a TODO comment marker because the similarity
between the MMIO and IO accessor behaviour is suspicious
and they could be combined, but this will be left to a
different patch.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC_BASE_IRQ macro is a leftover from when we shared code
between the GICv2 and the v7M NVIC. Since the NVIC is now
split off, GIC_BASE_IRQ is always 0, and we can just delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180824161819.11085-1-peter.maydell@linaro.org
The event queue management is broken today. Event records
are not properly written as EVT_SET_* macro was not updating
the actual event record. Also the event queue interrupt
is not correctly triggered.
Fixes: bb981004ea ("hw/arm/smmuv3: Event queue recording helper")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180921070138.10114-3-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a long story. Red Hat has relicensed Windows KVM device drivers
in 2018 and there was an agreement that to avoid WHQL driver conflict
software manufacturers should set proper PCI subsystem vendor ID in
their distributions. Thus PCI subsystem vendor id becomes actively used.
The problem is that this field is applied by us via hardware compats.
Thus technically it could be lost.
This patch adds PCI susbsystem id and vendor id to exportable parameters
for validation.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180918095852.28422-1-den@openvz.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
At the point smmu_find_add_as() gets called, the bus number might
not be computed. Let's change the name of IOMMU memory region and
just use the devfn and an incrementing index.
The name only is used for debug.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180921070138.10114-2-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: changed 'uint' to 'unsigned int']
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 datasheet says:
I2CD10 Interrupt Status Register
bit 2 Receive Done Interrupt status
S/W needs to clear this status bit to allow next data receiving
The Rx interrupt done interrupt status bit needs to be cleared
explicitly before the next byte can be received, and must therefore
not be auto-cleared. Also, receiving the next byte must be delayed
until the bit has been cleared.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Receive command handling may have to be deferred if a previous receive
done interrupt was not yet acknowledged. Move receive command handling
into a separate function to prepare for the necessary changes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aspeed i2c interrupts should be cleared by software only, and the bus
interrupt should be lowered when all interrupts have been cleared.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop TODO comment describing an issue which is
fixed later in the patch series, and clean up commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the base for a machine model of the BBC micro:bit:
https://en.wikipedia.org/wiki/Micro_Bit
This is a system with a nRF51 SoC containing the main processor, with
various peripherals on board.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-4-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nRF51 is a Cortex-M0 microcontroller with an on-board radio module,
plus other common ARM SoC peripherals.
http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
This defines a basic model of the CPU and memory, with no peripherals
implemented at this stage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-3-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: wrapped a few long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Like commit 16b4226(hw/acpi-build: Add a check for memory-less NUMA node
), it also needs to check memory length for NUMA nodes on ARM.
Signed-off-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180911112643.19296-1-shenglong.zsl@alibaba-inc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 97274d0c05 ("hw/char/exynos4210_uart.c: Remove unneeded
handling of NULL chardev") broke Exynos4210 support as it removed
NULL 'Chardev *chr' handling from exynos4210_uart_create() and
currently exynos4210_init() always passes NULL as 'Chardev *chr'
argument to exynos4210_uart_create() calls. Fix it by adding
missing serial_hd() calls to exynos4210_init().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 9310418.Wg32kryeWE@amdc3058
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
-----BEGIN PGP SIGNATURE-----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=A62f
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180925' into staging
ppc patch queue 2018-09-25
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
# gpg: Signature made Tue 25 Sep 2018 08:00:06 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180925:
40p: add fixed IRQ routing for LSI SCSI device
lsi53c895a: add optional external IRQ via qdev
scsi: remove unused lsi53c895a_create() and lsi53c810_create() functions
scsi: move lsi53c8xx_create() callers to lsi53c8xx_handle_legacy_cmdline()
scsi: add lsi53c8xx_handle_legacy_cmdline() function
sm501: Adjust endianness of pixel value in rectangle fill
spapr_pci: add an extra 'nr_msis' argument to spapr_populate_pci_dt
spapr: increase the size of the IRQ number space
spapr: introduce a spapr_irq class 'nr_msis' attribute
40p: use OR gate to wire up raven PCI interrupts
raven: some minor IRQ-related tidy-ups
hw/ppc: on 40p machine, change default firmware to OpenBIOS
target/ppc/cpu-models: Re-group the 970 CPUs together again
Record history of ppcemb target in common.json
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Whilst the PReP specification describes how all PCI IRQs are routed via IRQ
15 on the interrupt controller, the real 40p machine has a routing quirk in
that the LSI SCSI device is routed directly to IRQ 13.
Enable the external IRQ for the LSI SCSI device by wiring up the IRQ with
qdev to the relevant interrupt controller gpio.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On some early machines the on-board PCI devices IRQs are wired directly to
the interrupt controller instead of via the PCI host bridge.
Add an optional external IRQ that if wired up via qdev will replace the
in-built PCI IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As part of commits a64aa5785d "hw: Deprecate -drive if=scsi with non-onboard
HBAs" and b891538e81 "hw/ppc/prep: Fix implicit creation of "-drive if=scsi"
devices" the lsi53c895a_create() and lsi53c810_create() functions were added
to wrap pci_create_simple() and scsi_bus_legacy_handle_cmdline().
Unfortunately this prevents us from changing qdev properties on the device
and/or changing the PCI configuration. By switching over to using the new
lsi53c8xx_handle_legacy_cmdline() function then the caller can now configure
and realize the LSI SCSI device exactly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org> [arm parts]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The value from twoD_foreground (which is in host endian format) must
be converted to the endianness of the framebuffer (currently always
little endian) before it can be used to perform the fill operation.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that we don't have to call qdev_get_machine() to get the machine
class and the sPAPRIrq backend holding the number of MSIs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The new layout using static IRQ number does not leave much space to
the dynamic MSI range, only 0x100 IRQ numbers. Increase the total
number of IRQS for newer machines and introduce a legacy XICS backend
for pre-3.1 machines to maintain compatibility.
For the old backend, provide a 'nr_msis' value covering the full IRQ
number space as it does not use the bitmap allocator to allocate MSI
interrupt numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of MSI interrupts a sPAPR machine can allocate is in direct
relation with the number of interrupts of the sPAPRIrq backend. Define
statically this value at the sPAPRIrq class level and use it for the
"ibm,pe-total-#msi" property of the sPAPR PHB.
According to the PAPR specs, "ibm,pe-total-#msi" defines the maximum
number of MSIs that are available to the PE. We choose to advertise
the maximum number of MSIs that are available to the machine for
simplicity of the model and to avoid segmenting the MSI interrupt pool
which can be easily shared. If the pool limit is reached, it can be
extended dynamically.
Finally, remove XICS_IRQS_SPAPR which is now unused.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the PReP specification section 6.1.6 "System Interrupt
Assignments", all PCI interrupts are routed via IRQ 15.
Instead of mapping each PCI IRQ separately, we introduce an OR gate within the
raven PCI host bridge and then wire the single output of the OR gate to the
interrupt controller.
Note that whilst the (now deprecated) PReP machine still exists we still need
to preserve the old IRQ routing. This is done by adding a new "is-legacy-prep"
property to the raven PCI host bridge which is set to true for the PReP
machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This really lays the groundwork for the upcoming patches: it renames the
irqs PREPPCIState struct member to pci_irqs (as soon there will be a
distinction) and then changes the raven IRQ opaque to use PREPPCIState
instead of just irqs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
OpenBIOS gained 40p support in 5b20e4cace
Use it, instead of relying on an unmaintained and very limited firmware.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
-----BEGIN PGP SIGNATURE-----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=WnE4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180907' into staging
ppc patch queue 2018-09-07
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
# gpg: Signature made Fri 07 Sep 2018 08:30:02 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180907:
target-ppc: Extend HWCAP2 bits for ISA 3.0
target/ppc/kvm: set vcpu as online/offline
Fix a deadlock case in the CPU hotplug flow
spapr: Correct reference count on spapr-cpu-core
mac_newworld: implement custom FWPathProvider
uninorth: add ofw-addr property to allow correct fw path generation
mac_oldworld: implement custom FWPathProvider
grackle: set device fw_name and address for correct fw path generation
macio: add addr property to macio IDE object
macio: add macio bus to help with fw path generation
macio: move MACIOIDEState type declarations to macio.h
spapr_pci: fix potential NULL pointer dereference
spapr: fix leak of rev array
ppc: Remove deprecated ppcemb target
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAluQU38ACgkQIeENKd+X
cFRAXQgAlhNcwby+Jsk8sbLajMWXEtww9FIv+XESldPOJHmJyCkNDVZX8MuMM7+f
8NraD3YGDJvXP/BEcmyE5yPC6mx+OIi8ufzqP0rUML1x4+Tpxp8nZ7sBH197RtGg
eImPA6oKvg4wyfNOrZ+hGa8HF/iMT03TqeKggUPf3dVAs8LV2iUwBIzrRLB4IhIN
yFnhbcw8cW04tWUhYg4+viDY2k0q7fMrJZkASD/RjGMBjubJkwWvSYOdMIEWSpcG
2qLT5SohzUzHyKPONsoBKjSIP+nKgtyYR6IJh40FDd5S5RRMHe/n3q9jChIkHMma
x1eSNvVd41++QlBKqDeAlA+gbdK/uw==
=FJn/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-pullreq-20180905' into staging
A misc collection of RISC-V related patches for 3.1.
# gpg: Signature made Wed 05 Sep 2018 23:06:55 BST
# gpg: using RSA key 21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-pullreq-20180905:
riscv: remove define cpu_init()
hw/riscv/spike: Set the soc device tree node as a simple-bus
hw/riscv/virtio: Set the soc device tree node as a simple-bus
target/riscv: call gen_goto_tb on DISAS_TOO_MANY
target/riscv: optimize indirect branches
target/riscv: optimize cross-page direct jumps in softmmu
RISC-V: Simplify riscv_cpu_local_irqs_pending
RISC-V: Use atomic_cmpxchg to update PLIC bitmaps
RISC-V: Improve page table walker spec compliance
RISC-V: Update address bits to support sv39 and sv48
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
error_report and friends already add a "qemu-system-xxx" prefix
to the string, so a "qemu:" prefix is redundant in the string.
Just drop it.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1537495530-580-1-git-send-email-maozhongyi@cmss.chinamobile.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Add two functions to print an error/warning report once depending
on a passed-in condition variable and flip it if printed. This is
useful if you want to print a message not once-globally, but e.g.
once-per-device.
Inspired by warn_once() in hw/vfio/ccw.c, which has been replaced
with warn_report_once_cond().
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20180830145902.27376-2-cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Function comments reworded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
- split off the individual virtio-ccw devices into separate files
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEw9DWbcNiT/aowBjO3s9rk8bwL68FAluGaXsSHGNvaHVja0By
ZWRoYXQuY29tAAoJEN7Pa5PG8C+vD84QAKRKsoAGVq7qo+bAjqCVEQQXSKn9zII+
XDK7ZIQEPIQXks7nY/RFeRMLcP5i4WFcuW5PCg4LHTvptiAUGFzryOUc5qbB/1h8
fRxjwHxwDnc3zaDmx1aKpRTftX/tQuqgQX+N1Yr/2G/QdbKmTLN+WUlq9AT6YysJ
tkFNzKQgbze3ejHEdQKlioaQUuIwqrXzE5cBH/luLemrhoMghqP9W3CHmevKxXUO
0cUbGR4H2BWPaGcnxwtk9GHc4OZjKSJrH4JlKr3J5XBFZjJZO6nhsxzynbkPk0ll
xQlxrw0LGWVQPGJM51Ne5KPw9lElw4Fte1zmBXLpjHTAsBFT3Y0ImB1e8ALDaG8C
fejAlolHD5W6520GXrnCcTica71v7/7iaA7wg0jd8BDRopqNDgmrxdTT9vWTopRG
wrXihAA8r8Fwm+uPV+6qrCTr6B/v982OeIjnnlD4sQbWbIeH0EfetStQgGlcuO6t
tLPoZef8X4Qt05e71jrcVv802FlODoFbH+P26btL8jpnQdRQY4HKBPczjZIl/14Z
ZP6ORUHvN8w2k2Ld4esZzn2L3Kkpcpg79s+pBdIus4y+hnHSXlKe8Ipp4Nw/QFf6
h5C/p4ujchHyNPv30PfIHiqQIdVJuvC8gJvp7QnvK5nIlOqDAgeduvWZ9JI3Dj65
H7hKyqZR2HJr
=c1n9
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180829' into staging
- various fixes and improvements in the tcg code
- split off the individual virtio-ccw devices into separate files
# gpg: Signature made Wed 29 Aug 2018 10:38:03 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180829:
target/s390x: use regular spaces in translate.c
hw/s390x: Move virtio-ccw-blk code to a separate file
hw/s390x: Move virtio-ccw-net code to a separate file
hw/s390x: Move virtio-ccw-input code to a separate file
hw/s390x: Move virtio-ccw-gpu code to a separate file
hw/s390x: Move vhost-vsock-ccw code to a separate file
hw/s390x: Move virtio-ccw-crypto code to a separate file
hw/s390x: Move virtio-ccw-9p code to a separate file
hw/s390x: Move virtio-ccw-rng code to a separate file
hw/s390x: Move virtio-ccw-scsi code to a separate file
hw/s390x: Move virtio-ccw-balloon code to a separate file
hw/s390x: Move virtio-ccw-serial code to a separate file
hw/s390x/virtio-ccw: Consolidate calls to virtio_ccw_unrealize()
target/s390x: fix PACK reading 1 byte less and writing 1 byte more
target/s390x: add EX support for TRT and TRTR
target/s390x: fix IPM polluting irrelevant bits
target/s390x: fix CSST decoding and runtime alignment check
target/s390x: add BAL and BALR instructions
tests/tcg: add a simple s390x test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
to allow the correct customisation of the disk node names as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Set the fw_name property to "pci" and also set an explicit OFW address
using the value of the special_base property.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
virtio_queue_get_desc_addr returns 64-bit hwaddr while int is usually 32-bit.
If returned hwaddr is not equal to 0 but least-significant 32 bits are
equal to 0 then this code will not actually stop running queue.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Acked-by: Jia He <hejianet@gmail.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The first cpu unplug wasn't ever supported and corresponding
monitor/qmp commands refuse to unplug it. However guest is able
to issue eject request either using following command:
# echo 1 >/sys/devices/system/cpu/cpu0/firmware_node/eject
or directly writing to cpu hotplug registers, which makes
qemu crash with SIGSEGV following back trace:
kvm_flush_coalesced_mmio_buffer ()
while (ring->first != ring->last)
...
qemu_flush_coalesced_mmio_buffer
prepare_mmio_access
flatview_read_continue
flatview_read
address_space_read_full
address_space_rw
kvm_cpu_exec(cpu!0)
qemu_kvm_cpu_thread_fn
the reason for which is that ring == KVMState::coalesced_mmio_ring
happens to be a part of 1st CPU that was uplugged by guest.
Fix it by forbidding 1st cpu unplug from guest side and in addition
remove CPU0._EJ0 ACPI method to make clear that unplug of the first
CPU is not supported.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add hint to firmware (e.g. SeaBIOS) to reserve addtional
BUS/IO/MEM/PREF resource for legacy pci-pci bridge. Add the
resource reserve capability deleting in pci_bridge_dev_exitfn.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Factor "bus_reserve", "io_reserve", "mem_reserve", "pref32_reserve"
and "pref64_reserve" fields of the "GenPCIERootPort" structure out
to "PCIResReserve" structure, so that other PCI bridges can
reuse it to add resource reserve capability.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Because the cache is sized to include the rings and the event indices,
negotiating the VIRTIO_RING_F_EVENT_IDX feature will result in the size
of the cache changing. And because MemoryRegionCache accesses are
range-checked, if we skip this we end up with an assertion failure.
This happens with OpenBSD 6.3.
Reported-by: Fam Zheng <famz@redhat.com>
Fixes: 97cd965c07
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit
10efd7e108 "pc: acpi: fix memory hotplug regression by reducing stub SRAT entry size"
attemped to fix hotplug regression introduced by
848a1cc1e "hw/acpi-build: build SRAT memory affinity structures for DIMM devices"
fixed issue for Windows/3.0+ linux kernels, however it regressed 2.6 based
kernels (RHEL6) to the point where guest might crash at boot.
Reason is that 2.6 kernel discards SRAT table due too small last entry
which down the road leads to crashes. Hack I've tried in 10efd7e108 is also
not ACPI spec compliant according to which whole possible RAM should be
described in SRAT. Revert 10efd7e108 to fix regression for 2.6 based kernels.
With 10efd7e108 reverted, I've also tried splitting SRAT table statically
in different ways %/node and %/slot but Windows still fails to online
2nd pc-dimm hot-plugged into node 0 (as described in 10efd7e108) and
sometimes even coldplugged pc-dimms where affected with static SRAT
partitioning.
The only known so far way where Windows stays happy is when we have 1
SRAT entry in the last node covering all hotplug area.
Revert 848a1cc1e until we come up with a way to avoid regression
on Windows with hotplug area split in several entries.
Tested this with 2.6/3.0 based kernels (RHEL6/7) and WS20[08/12/12R2/16]).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To allow Linux to enumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Set the newly added register(KVM_REG_PPC_ONLINE) to indicate if the vcpu is
online(1) or offline(0)
KVM will use this information to set the RWMR register, which controls the PURR
and SPURR accumulation.
CC: paulus@samba.org
Signed-off-by: Nikunj A Dadhania <nikunj@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Switch from cpu_physical_memory_map to dma_memory_map,
so iommu mappings for virtio-gpu objects work properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-3-kraxel@redhat.com>
No functional change, just preparation for a followup patch
which needs a VirtIOGPU pointer.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-2-kraxel@redhat.com>
We need to set cs->halted to 1 before calling ppc_set_compat. The reason
is that ppc_set_compat kicks up the new thread created to manage the
hotplugged KVM virtual CPU and the code drives directly to KVM_RUN
ioctl. When cs->halted is 1, the code:
int kvm_cpu_exec(CPUState *cpu)
...
if (kvm_arch_process_async_events(cpu)) {
atomic_set(&cpu->exit_request, 0);
return EXCP_HLT;
}
...
returns before it reaches KVM_RUN, giving time to the main thread to
finish its job. Otherwise we can fall in a deadlock because the KVM
thread will issue the KVM_RUN ioctl while the main thread is setting up
KVM registers. Depending on how these jobs are scheduled we'll end up
freezing QEMU.
The following output shows kvm_vcpu_ioctl sleeping because it cannot get
the mutex and never will.
PS: kvm_vcpu_ioctl was triggered kvm_set_one_reg - compat_pvr.
STATE: TASK_UNINTERRUPTIBLE|TASK_WAKEKILL
PID: 61564 TASK: c000003e981e0780 CPU: 48 COMMAND: "qemu-system-ppc"
#0 [c000003e982679a0] __schedule at c000000000b10a44
#1 [c000003e98267a60] schedule at c000000000b113a8
#2 [c000003e98267a90] schedule_preempt_disabled at c000000000b11910
#3 [c000003e98267ab0] __mutex_lock at c000000000b132ec
#4 [c000003e98267bc0] kvm_vcpu_ioctl at c00800000ea03140 [kvm]
#5 [c000003e98267d20] do_vfs_ioctl at c000000000407d30
#6 [c000003e98267dc0] ksys_ioctl at c000000000408674
#7 [c000003e98267e10] sys_ioctl at c0000000004086f8
#8 [c000003e98267e30] system_call at c00000000000b488
crash> struct -x kvm.vcpus 0xc000003da0000000
vcpus = {0xc000003db4880000, 0xc000003d52b80000, 0xc0000039e9c80000, 0xc000003d0e200000, 0xc000003d58280000, 0x0, 0x0, ...}
crash> struct -x kvm_vcpu.mutex.owner 0xc000003d58280000
mutex.owner = {
counter = 0xc000003a23a5c881 <- flag 1: waiters
},
crash> bt 0xc000003a23a5c880
PID: 61579 TASK: c000003a23a5c880 CPU: 9 COMMAND: "CPU 4/KVM"
(active)
crash> struct -x kvm_vcpu.mutex.wait_list 0xc000003d58280000
mutex.wait_list = {
next = 0xc000003e98267b10,
prev = 0xc000003e98267b10
},
crash> struct -x mutex_waiter.task 0xc000003e98267b10
task = 0xc000003e981e0780
The following command-line was used to reproduce the problem (note: gdb
and trace can change the results).
$ qemu-ppc/build/ppc64-softmmu/qemu-system-ppc64 -cpu host \
-enable-kvm -m 4096 \
-smp 4,maxcpus=8,sockets=1,cores=2,threads=4 \
-display none -nographic \
-drive file=disk1.qcow2,format=qcow2
...
(qemu) device_add host-spapr-cpu-core,core-id=4
[no interaction is possible after it, only SIGKILL to take the terminal
back]
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit 93f874fe9d.
Now with virtio-vga being resetted properly the
crash workaround is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-3-kraxel@redhat.com
We must call the reset functions for both virtio-gpu
and vga to properly reset the combo device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-2-kraxel@redhat.com
spapr_init_cpus() currently creates spapr-cpu-core objects via
object_new() and setting their realized property to true. This leaves
their reference count at two, because object_new() adds an initial
reference and the realization attaches them to a default parent object
which also increments the reference count.
This causes a problem if one of these cores is hot unplugged: no
delete event is generated for it because it's reference count doesn't
reach zero when it is detached from it's parent.
Correct this by adding a call to object_unref() in spapr_init_cpus().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This contains the offset of the IDE controller within the macio address space
and is required to allow the address to be included within the fw path.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As the in-built IDE controller is attached to the macio bus then we should also
model this the same in QEMU to aid fw path generation.
Note that all existing macio devices are moved onto the new macio bus so that
the qdev tree accurately reflects the real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The generated qapi_event_send_FOO() take an Error ** argument. They
can't actually fail, because all they do with the argument is passing it
to functions that can't fail: the QObject output visitor, and the
@qmp_emit callback, which is either monitor_qapi_event_queue() or
event_test_emit().
Drop the argument, and pass &error_abort to the QObject output visitor
and @qmp_emit instead.
Suggested-by: Eric Blake <eblake@redhat.com>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815133747.25032-4-peterx@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message rewritten, update to qapi-code-gen.txt corrected]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BLK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542110-9017-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_NET has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542056-8927-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_INPUT has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-11-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_GPU has been set. This
can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-10-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VHOST_VSOCK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-9-git-send-email-thuth@redhat.com>
[CH: updated MAINTAINERS]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_CRYPTO has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-8-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_9P and CONFIG_VIRTFS
have been set. This can be done best if the code resides in a separate
file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-7-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_RNG has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-6-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SCSI has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-5-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BALLOON has been
set. This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-4-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SERIAL has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-3-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, every virtio-ccw device explicitely sets its unrealize
function to virtio_ccw_unrealize() in its class_init function.
We can simplify this by using a common unrealize function, just like
it is already done for the realize functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-2-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 2c88b098e7 added a call to SPAPR_MACHINE_GET_CLASS(spapr) in
spapr_phb_realize() before we check spapr isn't NULL. This causes QEMU
to crash when starting a non-pseries machine with a sPAPR PHB.
This could be fixed by setting the smc variable after the null check,
but it seems more explicit to use a ternary operator to skip the call
to SPAPR_MACHINE_GET_CLASS() if spapr is NULL, since spapr_phb_realize()
will return immediately in this case.
This was reported by Coverity (CID 1395170 and 1395183).
Fixes: 2c88b098e7
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduced in 04d595b300 ("spapr: do not use CPU_FOREACH_REVERSE",
2018-08-23)
Fixes: CID1395181
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace all the trace_vtd_err_*() hooks with the new error_report_once()
since they are similar to trace_vtd_err() - dumping the first error
would be mostly enough, then we have them on by default too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-4-peterx@redhat.com>
[Use "%x" instead of "%" PRIx16 to print uint16_t, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Replace existing trace_vtd_err() with error_report_once() then stderr
will capture something if any of the error happens, meanwhile we don't
suffer from any DDOS. Then remove the trace point. Since at it,
provide more information where proper (now we can pass parameters into
the report function).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[Two format strings fixed, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix passing argument for nanoMIPS bare metal related to the
semihosting regime.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Setup the GT64120 BARs in the nanoMIPS bootloader, in the same way that
they are setup in the MIPS32 bootloader. This is necessary for Linux to
be able to access peripherals, including the UART.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Paul Burton <pburton@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add basic nanoMIPS boot code for Malta.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
-----BEGIN PGP SIGNATURE-----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=2bke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/check/20180822' into staging
check/next for 20180822
# gpg: Signature made Wed 22 Aug 2018 09:03:40 BST
# gpg: using RSA key F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/check/20180822:
check: Only test tpm devices when they are compiled in
check: Only test usb-ehci when it is compiled in
check: Only test usb-uhci devices when they are compiled in
check: Only test usb-ohci when it is compiled in
check: Only test nvme when it is compiled in
check: Only test pvpanic when it is compiled in
check: Only test wdt_ib700 when it is compiled in
check: Only test sdhci when it is compiled in
check: Only test i82801b11 when it is compiled in
check: Only test ioh3420 when it is compiled in
check: Only test ipack when it is compiled in
check: Only test hda when it is compiled in
check: Only test ac97 when it is compiled in
check: Only test es1370 when it is compiled in
check: Only test rtl8139 when it is compiled in
check: Only test pcnet when it is compiled in
check: Only test eepro100 when it is compiled in
check: Only test ne2000 when it is compiled in
check: Only test vmxnet3 when it is compiled in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix MPS2 SCC config register values for the mps2-an511
and mps2-an385 boards:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be the board number in hex, not decimal
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180823175225.22612-1-peter.maydell@linaro.org
Refactor bcm2835_fb_mbox_push() to work by calling
bcm2835_fb_validate_config() and bcm2835_fb_reconfigure(),
so that config set this way is also validated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-9-peter.maydell@linaro.org
Validate the config settings that the guest tries to set.
The wiki page documentation is not really accurate here:
generally rather than failing requests to set bad parameters,
the hardware will just clip them to something sensible.
Validate the most important parameters: sizes and
the viewport offsets. This prevents the framebuffer
code from trying to read out-of-range memory.
In the property handling code, we validate the new parameters every
time we encounter a tag that sets them. This means we validate the
config multiple times if the request includes multiple config-setting
tags, but the code would require significant restructuring to do a
validation only once but still return the clipped settings for
get-parameter tags and the buffer allocation tag.
Validation of settings made via the older bcm2835_fb_mbox_push()
function will be done in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-8-peter.maydell@linaro.org
The raspi framebuffir in bcm2835_fb supports the definition
of a virtual "viewport", which is smaller than the full
physical framebuffer size and at an adjustable offset within
it. Only the viewport area is sent to the screen. This allows
the guest to do things like double buffering, or scrolling
by adjusting the viewport origin. Currently QEMU doesn't
implement this at all.
Add support for this feature:
* the property mailbox code needs to distinguish the
virtual width/height from the physical width/height
* the framebuffer code needs to do something with the
virtual width/height/origin information
Note that the wiki documentation on the semantics of the
virtual and physical height and width has it the wrong way
around -- the virtual size is the size of the allocated
buffer, and the physical size is the size of the display,
so the virtual size is always the same as or larger than
the physical.
If the viewport size is set smaller than the physical
screen size, we ignore the viewport settings completely
and just display the physical screen area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-7-peter.maydell@linaro.org
Abstract out the calculation of the pitch and size of the
framebuffer into functions that operate on the BCM2835FBConfig
struct -- these are about to get a little more complicated
when we add support for virtual and physical sizes differing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-6-peter.maydell@linaro.org
The bcm2835_fb's initial resolution and other parameters are set
via QOM properties. We should reset to those initial values on
device reset, which means we need to save the QOM property
values somewhere that they are not overwritten by guest
changes to the framebuffer configuration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-5-peter.maydell@linaro.org
The BCM2835FBState struct has a 'pitch' field which is a
cached copy of xres * (bpp >> 3), and a 'size' field which is
a cached copy of pitch * yres. However we don't actually do
anything with these fields; delete them. We retain the
now-unused slots in the VMState struct for migration
compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-4-peter.maydell@linaro.org
Refactor the fb property setting code so that rather than
using a set of pointers to local variables to track
whether a config value has been updated in the current
mbox and if so what its new value is, we just copy
all the current settings of the fb at the start, and
then update that copy as we go along, before asking
the fb to switch to it at the end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-3-peter.maydell@linaro.org
The handling of framebuffer properties in the bcm2835_property code
is a bit clumsy, because for each of the many fb related properties
we try to track the value we're about to set and whether we're going
to be setting a value, and then we hand all the new values off
to the framebuffer via a function which takes them all as separate
arguments. It would be simpler if the property code could easily
copy all the framebuffer's current settings, update them with
the new specified values and then ask the framebuffer to switch
to the new set.
As the first part of this refactoring, pull all the fb config
settings fields in BCM2835FBState out into their own struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-2-peter.maydell@linaro.org
Some of the config register values we were setting for the MPS2 SCC
weren't correct:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be 0x505, not decimal 505
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-23-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The SPI controllers in the MPS2 AN505 board are PL022s.
We have a model of the PL022, so create these devices.
We don't currently model the LCD controller that sits behind
one of the PL022s; the others are intended to control devices
that sit on the FPGA's general purpose SPI connector or
"shield" expansion connectors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-22-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In the PL022, register offset 0x20 is the ICR, a write-only
interrupt-clear register. Register offset 0x24 is DMACR, the DMA
control register. We were incorrectly implementing (a stub version
of) DMACR at 0x20, and not implementing anything at 0x24. Fix this
bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-21-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL022 interrupt registers have bits allocated as:
0: ROR (receive overrun)
1: RT (receive timeout)
2: RX (receive FIFO half full or less)
3: TX (transmit FIFO half full or less)
A cut and paste error meant we had the wrong value for
the PL022_INT_RT constant. This bug doesn't affect device
behaviour, because we don't implement the receive timeout
feature and so never set that interrupt bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-20-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move from the legacy SysBusDevice::init method to using
DeviceState::realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-19-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Use the DeviceState vmsd pointer rather than calling vmstate_register()
directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-18-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the PL022 calls pl022_reset() from its class init
function. Make it register a DeviceState reset method instead,
so that we reset the device on system reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-17-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The AN505 FPGA image includes four PL081 DMA controllers, each
of which is gated by a Master Security Controller that allows
the guest to prevent a non-secure DMA controller from accessing
memory that is used by secure guest code. Create and wire
up these devices.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-15-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit doesn't have any MSCs itself but it does need
some wiring to connect the external signals from MSCs
in the outer board model up to the registers and the
NVIC IRQ line.
We also need to expose a MemoryRegion corresponding to
the AHB bus, so that MSCs in the outer board model can
use that as their downstream port. (In the FPGA this is
the "AHB Slave Expansion" ports shown in the block
diagram in the AN505 documentation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-14-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit does not have any Master Security Contollers itself,
but it does provide registers in the secure privilege control
block which allow control of MSCs in the external system.
Add support for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-13-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the system control element's register banks
(sysctl and sysinfo).
This is the last of the previously completely unimplemented
components in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-11-peter.maydell@linaro.org
Implement the IoTKit system control element's system information
block; this is just a pair of read-only version/config registers,
plus the usual PID/CID ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-10-peter.maydell@linaro.org
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
The IoTKit has a CMSDK timer device that runs on the S32KCLK.
Create this and wire it up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-8-peter.maydell@linaro.org
The IoTKit includes three different instances of the
CMSDK APB watchdog; create and wire them up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-7-peter.maydell@linaro.org
The MPS2 FPGA images for the Cortex-M3 (mps2-an385 and mps2-511)
both include a CMSDK dual-timer module. Wire this up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-6-peter.maydell@linaro.org
Now we have a model of the CMSDK dual timer, we can wire it
up in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-5-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
In the MPS2 FPGAIO, PSCNTR is a free-running downcounter with
a reload value configured via the PRESCALE register, and
COUNTER counts up by 1 every time PSCNTR reaches zero.
Implement these counters.
We can just increment the counters migration subsection's
version ID because we only added it in the previous commit,
so no released QEMU versions will be using it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-3-peter.maydell@linaro.org
The MPS2 FPGAIO block includes some simple free-running counters.
Implement these.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-2-peter.maydell@linaro.org
The kernel booting specification for an AArch32 kernel requires that
it is booted in Hyp mode if available; otherwise the kernel can't
enable KVM. We were incorrectly leaving the kernel in SVC mode.
If we're booting an AArch32 kernel in the Nonsecure state and Hyp
mode is available, start in it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-7-peter.maydell@linaro.org
Add a "virtualization" property to the vexpress-a15 board,
controlling presence of EL2. As with EL3, we default to
enabling it, but the user can disable it if they have an
older guest which can't cope with it being present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-10-peter.maydell@linaro.org
Don't request that the arm_load_kernel() code should boot in secure
state if the CPU doesn't have a secure state. Currently this
doesn't make a difference because the boot.c code only examines
the secure_boot flag in code guarded by an ARM_FEATURE_EL3 check,
but upcoming changes for supporting booting into Hyp mode will
change that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-9-peter.maydell@linaro.org
For the A15MPCore internal peripheral object, we handle GIC
security extensions support by checking whether the CPUs
have EL3 enabled; if so then we enable it also on the GIC.
Handle the virtualization extensions in the same way: if the
CPU has EL2 then enable it on the GIC and wire up the
virtualization-specific memory regions and the maintenance
interrupt.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-8-peter.maydell@linaro.org
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-7-peter.maydell@linaro.org
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-6-peter.maydell@linaro.org
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-5-peter.maydell@linaro.org
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-4-peter.maydell@linaro.org
Reduce the size of the per-cpu GICH memory regions from 0x1000
to 0x200. The registers only cover 0x200 bytes, and the Cortex-A15
wants to map them at a spacing of 0x200 bytes apart. Having the
region be too large interferes with mapping them like that, so
reduce it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-3-peter.maydell@linaro.org
* qumu-guest-agent freeze-hook tweak (Christian)
* pm_smbus improvements (Corey)
* Move validation to pre_plug for pc-dimm (David)
* Fix memory leaks (Eduardo, Marc-André)
* synchronization profiler (Emilio)
* Convert the CPU list to RCU (Emilio)
* LSI support for PPR Extended Message (George)
* vhost-scsi support for protection information (Greg)
* Mark mptsas as a storage device in the help (Guenter)
* checkpatch tweak cherry-picked from Linux (me)
* Typos, cleanups and dead-code removal (Julia, Marc-André)
* qemu-pr-helper support for old libmultipath (Murilo)
* Annotate fallthroughs (me)
* MemoryRegionOps cleanup (me, Peter)
* Make s390 qtests independent from libqos, which doesn't actually support it (me)
* Make cpu_get_ticks independent from BQL (me)
* Introspection fixes (Thomas)
* Support QEMU_MODULE_DIR environment variable (ryang)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAlt+5OYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPtxwf8CQM/F+0L+EKeYfYcVgVZsDhhOkLj
Pm61q0bZsWKLby5jCqIDYw7Z/vodJnSS1DO0slIRoXxvQ9DwlkbBnBy/aG/E9U0q
WF1vbCezibDIt7sGcsu9F5zXU9eqe+E6dZfxFrv8FQSOFVxn34TfeJagWLCtzg0d
LnVTF/e4zJD8IQiM7w6lJQxua3fz13ssPEg2KnMkguDhACMwvZ/K/cA2AJkHRMhY
sroPMwLHlrF1NOoeCIrWxYUmSGCRCAy1DmiPGiiSs0yBq/dL0UkAa5Eu6HMQ7rgI
zUff3JDmzEjixUSIEbpVRN+yPCN0/ACSOpJUrKLDxXbc4nZ+PBQ04YpyPQ==
=UZiV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* x86 TCG fixes for 64-bit call gates (Andrew)
* qumu-guest-agent freeze-hook tweak (Christian)
* pm_smbus improvements (Corey)
* Move validation to pre_plug for pc-dimm (David)
* Fix memory leaks (Eduardo, Marc-André)
* synchronization profiler (Emilio)
* Convert the CPU list to RCU (Emilio)
* LSI support for PPR Extended Message (George)
* vhost-scsi support for protection information (Greg)
* Mark mptsas as a storage device in the help (Guenter)
* checkpatch tweak cherry-picked from Linux (me)
* Typos, cleanups and dead-code removal (Julia, Marc-André)
* qemu-pr-helper support for old libmultipath (Murilo)
* Annotate fallthroughs (me)
* MemoryRegionOps cleanup (me, Peter)
* Make s390 qtests independent from libqos, which doesn't actually support it (me)
* Make cpu_get_ticks independent from BQL (me)
* Introspection fixes (Thomas)
* Support QEMU_MODULE_DIR environment variable (ryang)
# gpg: Signature made Thu 23 Aug 2018 17:46:30 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
KVM: cleanup unnecessary #ifdef KVM_CAP_...
target/i386: update MPX flags when CPL changes
i2c: pm_smbus: Add the ability to force block transfer enable
i2c: pm_smbus: Don't delay host status register busy bit when interrupts are enabled
i2c: pm_smbus: Add interrupt handling
i2c: pm_smbus: Add block transfer capability
i2c: pm_smbus: Make the I2C block read command read-only
i2c: pm_smbus: Fix the semantics of block I2C transfers
i2c: pm_smbus: Clean up some style issues
pc-dimm: assign and verify the "addr" property during pre_plug
pc: drop memory region alignment check for 0
util/oslib-win32: indicate alignment for qemu_anon_ram_alloc()
pc-dimm: assign and verify the "slot" property during pre_plug
ipmi: Use proper struct reference for BT vmstate
vhost-scsi: expose 't10_pi' property for VIRTIO_SCSI_F_T10_PI
vhost-scsi: unify vhost-scsi get_features implementations
vhost-user-scsi: move host_features into VHostSCSICommon
cpus: allow cpu_get_ticks out of BQL
cpus: protect TimerState writes with a spinlock
seqlock: add QemuLockable support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PIIX4 hardware has block transfer buffer always enabled in
the hardware, but the i801 does not. Add a parameter to pm_smbus_init
to force on the block transfer so the PIIX4 handler can enable this
by default, as it was disabled by default before.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-9-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change 880b1ffe6e "smbus: do not immediately complete commands"
changed pm_smbus to delay setting the host busy bit until the status
register was read, to work around a bug in AMIBIOS. Unfortunately,
when interrupts are enabled, the status register will never get read
and the processing will never happen.
Modify the code to only delay setting the host busy bit if interrupts
are not enabled.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Hervé Poussineau <hpoussin@reactos.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1534796770-10295-8-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the necessary code so that interrupts actually work from
the pm_smbus device.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-7-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There was no block transfer code in pm_smbus.c, and it is needed
for some devices. So add it.
This adds both byte-by-byte block transfers and buffered block
transfers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-5-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It did have write capability, but the manual says the behavior
with write enabled is undefined. So just set an error in this
case.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-4-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The I2C block transfer commands was not implemented correctly, it
read a length byte and such like it was an smbus transfer.
So fix the smbus_read_block() and smbus_write_block() functions
so they can properly handle I2C transfers, and normal SMBus
transfers (for upcoming changes). Pass in a transfer size and
a bool to know whether to use the size byte (like SMBus) or use
the length given (like I2C).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-3-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix some spacing issues, remove extraneous comments, add some
defines instead of hard-coding numbers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-2-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can assign and verify the address before realizing and trying to plug.
reading/writing the address property should never fail for DIMMs, so let's
reduce error handling a bit by using &error_abort. Getting access to the
memory region now might however fail. So forward errors from
get_memory_region() properly.
As all memory devices should use the alignment of the underlying memory
region for guest physical address asignment, do detection of the
alignment in pc_dimm_pre_plug(), but allow pc.c to overwrite the
alignment for compatibility handling.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All applicable memory regions always have an alignment > 0. All memory
backends result in file_ram_alloc() or qemu_anon_ram_alloc() getting
called, setting the alignment to > 0.
So a PCDIMM memory region always has an alignment > 0. NVDIMM copy the
alignment of the original memory memory region into the handcrafted memory
region that will be used at this place.
So the check for 0 can be dropped and we can reduce the special
handling.
Dropping this check makes factoring out of alignment handling easier as
compat handling only has to look at pcmc->enforce_aligned_dimm and not
care about the alignment of the memory region.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can assign and verify the slot before realizing and trying to plug.
reading/writing the slot property should never fail, so let's reduce
error handling a bit by using &error_abort.
To do this during pre_plug, add and use (x86, ppc) pc_dimm_pre_plug().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The vmstate for isa_ipmi_bt was referencing into the bt structure,
instead create a bt structure separate and use that.
The version 1 of the BT transfer was fairly broken, if a migration
occured during an IPMI operation, it is likely the migration would
be corrupted because I misunderstood the VMSTATE_VBUFFER_UINT32()
handling, I thought it handled transferring the length field,
too. So I just remove support for that. I doubt anyone is using
it at this point.
This also removes the transfer of use_irq, since that should come
from configuration.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1534798644-13587-1-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow toggling on/off the VIRTIO_SCSI_F_T10_PI feature bit for both
vhost-scsi and vhost-user-scsi devices.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-4-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the enablement of preset host features into the common
vhost_scsi_common_get_features() function. This is in preparation for
having vhost-scsi also make use of host_features.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-3-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch the apic away from using the old_mmio MemoryRegionOps
accessor functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180803101943.23722-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This paves the way for implementing the CPU list with an RCU list,
which cannot be traversed in reverse order.
Note that this is the only caller of CPU_FOREACH_REVERSE.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-11-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LSI 53c895a code does not handle the PPR Extended Message. Add
support to handle PPR Extended Message like SDTR and WDTR are handled.
That is, to skip past the message bytes and ignore the message.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A new error path fails to close the device file descriptor when
triggered by a ballooning incompatibility within the group. Fix it.
Fixes: 238e917285 ("vfio/ccw/pci: Allow devices to opt-in for ballooning")
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fix error reported by Coverity where realpath can return NULL,
resulting in a segfault in strcmp(). This should never happen given
that we're working through regularly structured sysfs paths, but
trivial enough to easily avoid.
Fixes: 238e917285 ("vfio/ccw/pci: Allow devices to opt-in for ballooning")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is currently a funny problem with the "mc146818rtc" device:
1) Start QEMU like this:
qemu-system-ppc64 -M pseries -S
2) At the HMP monitor, enter "info qom-tree". Note that there is an
entry for "/rtc (spapr-rtc)".
3) Introspect the mc146818rtc device like this:
device_add mc146818rtc,help
4) Run "info qom-tree" again. The "/rtc" entry is gone now!
The rtc_finalize() function of the mc146818rtc device has two bugs: First,
it tries to remove a "rtc" property, while the rtc_realizefn() added a
"rtc-time" property instead. And second, it should have been done in an
unrealize function, not in a finalize function, to avoid that this causes
problems during introspection.
But since adding aliases to the global machine state should not be done
from a device's realize function anyway, let's rather fix this issue
by moving the creation of the alias to the code that creates the device
(and thus is run from the machine init functions instead), i.e. the
mc146818_rtc_init() function for most machines. The prep machines are
special, since the mc146818rtc device is created here in the realize
function of the i82378 device. Since we certainly don't want to add the
alias there, we add it to some code that is called from the ibm_40p_init()
machine init function instead.
Since the alias is now only created during the machine init, we can remove
the object_property_del() completely.
Fixes: 654a36d857
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1534419358-10932-5-git-send-email-thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mc146818rtc.c still contains some TABs. Replace them with spaces.
And while we're at it, also delete trailing whitespace in this file.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1534419358-10932-4-git-send-email-thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these are marked as "intentional/fix required" because they
just need adding a fall through comment. This is exactly what this
patch does, except for target/mips/translate.c where it is easier to
duplicate the code, and hw/audio/sb16.c where I consulted the DOSBox
sources and decide to just remove the LOG_UNIMP before the fallthrough.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the automatic subregister extraction from the memory API, and avoid
that Coverity complains about missing fallthrough comments.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mptsas1068 is currently listed as uncategorized device.
Mark it as storage device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1533076133-22745-1-git-send-email-linux@roeck-us.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was not possible to compile out pvpanic. Use the same trick
than applesmc.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Here's my first ppc & spapr pull request for qemu-3.1. This contains
a bunch of things that have accumulated while 3.0 was in freeze.
Highlights are:
* SLOF firmware update
* A number of floating point cleanups from Richard Henderson and
Yasmin Beatriz
* A new model for assigning irq numbers on spapr, this is an
important preliminary step towards implementing the POWER9
"XIVE" interrupt controller
-----BEGIN PGP SIGNATURE-----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=viH7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180821' into staging
ppc patch queue 2018-08-21
Here's my first ppc & spapr pull request for qemu-3.1. This contains
a bunch of things that have accumulated while 3.0 was in freeze.
Highlights are:
* SLOF firmware update
* A number of floating point cleanups from Richard Henderson and
Yasmin Beatriz
* A new model for assigning irq numbers on spapr, this is an
important preliminary step towards implementing the POWER9
"XIVE" interrupt controller
# gpg: Signature made Tue 21 Aug 2018 05:32:44 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180821: (26 commits)
ppc: add DBCR based debugging
spapr_pci: factorize the use of SPAPR_MACHINE_GET_CLASS()
mac_newworld: don't use legacy fw_cfg_init_mem() function
mac_oldworld: don't use legacy fw_cfg_init_mem() function
40p: don't use legacy fw_cfg_init_mem() function
qemu-doc: mark ppc/prep machine as deprecated
hw/ppc: deprecate the machine type 'prep', replaced by '40p'
spapr: introduce a IRQ controller backend to the machine
hw/ppc/ppc405_uc: Convert away from old_mmio
hw/ppc/ppc_boards: Don't use old_mmio for ref405ep_fpga
hw/ppc/prep: Remove ifdeffed-out stub of XCSR code
spapr: introduce a fixed IRQ number space
spapr: Add a pseries-3.1 machine type
target/ppc: simplify bcdadd/sub functions
xics: don't include "target/ppc/cpu-qom.h" in "hw/ppc/xics.h"
vfio/spapr: Allow backing bigger guest IOMMU pages with smaller physical pages
target/ppc: bcdsub fix sign when result is zero
target/ppc: Use non-arithmetic conversions for fp load/store
target/ppc: Honor fpscr_ze semantics and tidy fre, fresqrt
target/ppc: Tidy helper_fsqrt
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This includes nvdimm persistence fixes queued before the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbepoTAAoJECgfDbjSjVRpLioH/3BPps8FLh4x2gZSq3B+u72O
RYUA3I3TilEGyc9yf8o7e1Hf+pQAJBEmulcnKxXFVWZIJ1GVLPt4NZCMQGiPDnJL
+RCT/Q64PUy09hRjddAasikrvXa4YOsRgBgJJToO7v9PSQSaU3fC7O3hNea7KcF/
C4SSqkUgxyDhCCYHHblpKxFz/wtwy4ZaCGSdozIdmKNPJ6/ye8wOQ1Mq9e1Mwp18
S6ilJub5IwB6aM2KVMmX4AFomF4u2cn153ts8fI+Dyo4/NE6P4+viDlz3BOBKdzm
kmd49h6/n4Lenoo4oI1yNHSuIJJTVfvnoLu6rG7mPbQKgxNd1uN4KuUIygU5PCY=
=Xcaj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc: fixes
This includes nvdimm persistence fixes queued before the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 20 Aug 2018 11:38:11 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
migration/ram: ensure write persistence on loading all data to PMEM.
migration/ram: Add check and info message to nvdimm post copy.
mem/nvdimm: ensure write persistence to PMEM in label emulation
hostmem-file: add the 'pmem' option
configure: add libpmem support
memory, exec: switch file ram allocation functions to 'flags' parameters
memory, exec: Expose all memory block related flags.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x-root was renamed as such owing to the experimental nature of the
property; the underlying filesystem semantics were undecided
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-6-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To support larger file transfers, rely on a short packet
to detect end of the data phase and rewrite d->length to
the size received
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-5-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
For large buffers, write may not copy the full buffer. For example,
on Linux, write imposes a limit of 0x7ffff000. Note that this does
not fix >4G transfers but ~>2G files will transfer successfully.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_mtp_realloc() was being incorrectly used when allocating
buffer for incoming data. Set d->length only after resizing
the buffer.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The initiator can choose to cancel an ongoing request which
is specified by bRequest=0x64. If such a request arrives,
free up any pending state
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is mandated by the ohci specification. It tells at 6.4.4 on page 104
that for transfer descriptors that are retired with an error the done
queue interrupt counter is cleared as if the interrupt delay field of the
descriptions were zero.
Before this change, error conditions were handled similarly to the
successful condition which is especially troublesome for control transfers.
Some drivers (e.g., the AmigaOS-one) as well as the example code in the
spec, set the setup stage with an interrupt delay of seven (which means no
interrupt). This is fine under normal conditions, because one usually
doesn't want to be notified about the completion of this stage. However, if
an error occurs in this stage, these drivers will not get notified with the
current implementation. The fix addresses this by following the spec more
closely. Also, otherwise, the ability to set interrupt delay to seven would
be useless.
Note that Linux drivers that I looked at don't seem to be affected as they
set six as the interrupt delay presumably for the reason that they won't
get notified otherwise.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Message-id: 20180729191928.11254-1-mail@sebastianbauer.info
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move away from the old_mmio MemoryRegion accessors in the
bonito pci controller.
This device is used only in the MIPS "fulong2e" machine.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180802155147.1863-3-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Convert the vga-isa-mm device away from the old_mmio
MemoryRegion accessors.
This device is only used by the MIPS 'jazz' boards
"magnum" and "pica61".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 20180802155147.1863-2-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
According to the ramfb_setup() function, the ramfb device needs fw_cfg
with DMA, so we should also only compile and link it into those targets
which support it, to avoid that the device shows up on systems where it
can not be used at all (e.g. s390x).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1534786083-26559-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It should save us some CPU cycles as these routines perform a lot of
checks.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead initialise the device via qdev to allow us to set device properties
directly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead initialise the device via qdev to allow us to set device properties
directly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead initialise the device via qdev to allow us to set device properties
directly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- prep machine is a fictional machine, so has no specifications. Which
devices can be changed/added/removed without impact? Are interrupts
correctly mapped?
- prep firmware (OHW) has support only for IDE drives (no SCSI).
Booting from IDE has been broken approximatively 3 years ago, and nobody complained.
- OHW is limited on IDE boot to a specific set of OS loaders.
These operating systems are of the 2004 time frame.
- OHW can use -kernel. Linux kernel freezes a long time after PS/2 mouse
detection, and then screen becomes garbage. This was already broken in
QEMU v2.7, 2 years ago, and nobody complained.
On the other side:
- 40p is a real machine, so emulation can be checked against
hardware specifications
- OpenBIOS has support for SCSI block devices, including 40p LSI adapter
- OpenBIOS can start mostly all Linux kernels (including recent ones)
and recent operating system (like NetBSD 7.1.2)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[dwg: Drop prep from boot-serial test to avoid deprecation warnings]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This proposal moves all the related IRQ routines of the sPAPR machine
behind a sPAPR IRQ backend interface 'spapr_irq' to prepare for future
changes. First of which will be to increase the size of the IRQ number
space, then, will follow a new backend for the POWER9 XIVE IRQ controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Convert the devices in ppc405_uc away from using the old_mmio
MemoryRegion accessors:
* opba's 32-bit and 16-bit accessors were just calling the
8-bit accessors and assembling a big-endian order number,
which we can do by setting the .impl.max_access_size to 1
and the endianness to DEVICE_BIG_ENDIAN, and letting the
core memory code do the assembly
* ppc405_gpio's accessors were all just stubs
* ppc4xx_gpt's 8-bit and 16-bit accessors were treating the
access as invalid, which we can do by setting the
.valid.min_access_size and .valid.max_access_size fields
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch the ref405ep_fpga device away from using the old_mmio
MemoryRegion accessors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The prep machine has some code which is stubs of accessors
for XCSR registers. This has been disabled via #if 0
since commit b6b8bd1819 in 2004, and doesn't have any
actual interesting content. It also uses the deprecated
old_mmio accessor functions. Remove it entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This proposal introduces a new IRQ number space layout using static
numbers for all devices, depending on a device index, and a bitmap
allocator for the MSI IRQ numbers which are negotiated by the guest at
runtime.
As the VIO device model does not have a device index but a "reg"
property, we introduce a formula to compute an IRQ number from a "reg"
value. It should minimize most of the collisions.
The previous layout is kept in pre-3.1 machines raising the
'legacy_irq_allocation' machine class flag.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
