The gdb CSR xml file has registers in documentation order, not numerical
order, so we need a table to map the register numbers. This also adds
fairly standard gdb hooks to access xml specified registers.
notice:
The fpu xml from gdb 8.3 has unused register #, 65 and make first
csr register # become 69. We register extra register on gdb to correct
csr offset calculation
Signed-off-by: Jim Wilson <jimw@sifive.com>
Signed-off-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a debugger field to CPURISCVState. Add riscv_csrrw_debug function
to set it. Disable mode checks when debugger field true.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190212230903.9215-1-jimw@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds some missing CSR_* register macros, and documents some as being
priv v1.9.1 specific.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190212230830.9160-1-jimw@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
during the refactor to decodetree we removed the manual decoding that is
necessary for c.jal/c.addiw and removed the translation of c.flw/c.ld
and c.fsw/c.sd. This reintroduces the manual parsing and the
omited implementation.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Tested-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Within a delay slot, we were squishing both DISAS_IAQ_N_STALE and
DISAS_IAQ_N_STALE_EXIT to DISAS_IAQ_N_UPDATED. This lost the
required exit to the main loop, and could result in interrupts
never being delivered.
Tested-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These instructions do not trap when SVE is disabled in EL0,
causing them to be executed with wrong size information.
Signed-off-by: Amir Charif <amir.charif@cea.fr>
Message-id: 1552579248-31025-1-git-send-email-amir.charif@cea.fr
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added 'target/arm' prefix to subject]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some generic arch timer registers are Config-RW in the EL0,
which means the EL0 exception level can have write permission
if it is appropriately configured.
When VM access registers, QEMU firstly checks whether they have RW
permission, then check whether it is appropriately configured.
If they are defined to read only in EL0, even though they have been
appropriately configured, they still do not have write permission.
So need to add the write permission according to ARMV8 spec when
define it.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Message-id: 1552395177-12608-1-git-send-email-gengdongjiu@huawei.com
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bastian: this patchset converts the RISC-V decoder to decodetree in four major steps:
1) Convert 32-bit instructions to decodetree [Patch 1-15]:
Many of the gen_* functions are called by the decode functions for 16-bit
and 32-bit functions. If we move translation code from the gen_*
functions to the generated trans_* functions of decode-tree, we get a lot of
duplication. Therefore, we mostly generate calls to the old gen_* function
which are properly replaced after step 2).
Each of the trans_ functions are grouped into files corresponding to their
ISA extension, e.g. addi which is in RV32I is translated in the file
'trans_rvi.inc.c'.
2) Convert 16-bit instructions to decodetree [Patch 16-18]:
All 16 bit instructions have a direct mapping to a 32 bit instruction. Thus,
we convert the arguments in the 16 bit trans_ function to the arguments of
the corresponding 32 bit instruction and call the 32 bit trans_ function.
3) Remove old manual decoding in gen_* function [Patch 19-29]:
this move all manual translation code into the trans_* instructions of
decode tree, such that we can remove the old decode_* functions.
Palmer: This, with some additional cleanup patches, passed Alistar's
testing on rv32 and rv64 as well as my testing on rv64, so I think it's
good to go. I've run my standard test against this exact tag.
I still don't have a Mac to try this on, sorry!
-----BEGIN PGP SIGNATURE-----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=t7se
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.0-sf4' into staging
target/riscv: Convert to decodetree
Bastian: this patchset converts the RISC-V decoder to decodetree in four major steps:
1) Convert 32-bit instructions to decodetree [Patch 1-15]:
Many of the gen_* functions are called by the decode functions for 16-bit
and 32-bit functions. If we move translation code from the gen_*
functions to the generated trans_* functions of decode-tree, we get a lot of
duplication. Therefore, we mostly generate calls to the old gen_* function
which are properly replaced after step 2).
Each of the trans_ functions are grouped into files corresponding to their
ISA extension, e.g. addi which is in RV32I is translated in the file
'trans_rvi.inc.c'.
2) Convert 16-bit instructions to decodetree [Patch 16-18]:
All 16 bit instructions have a direct mapping to a 32 bit instruction. Thus,
we convert the arguments in the 16 bit trans_ function to the arguments of
the corresponding 32 bit instruction and call the 32 bit trans_ function.
3) Remove old manual decoding in gen_* function [Patch 19-29]:
this move all manual translation code into the trans_* instructions of
decode tree, such that we can remove the old decode_* functions.
Palmer: This, with some additional cleanup patches, passed Alistar's
testing on rv32 and rv64 as well as my testing on rv64, so I think it's
good to go. I've run my standard test against this exact tag.
I still don't have a Mac to try this on, sorry!
# gpg: Signature made Wed 13 Mar 2019 13:44:49 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.0-sf4: (29 commits)
target/riscv: Remove decode_RV32_64G()
target/riscv: Remove gen_system()
target/riscv: Rename trans_arith to gen_arith
target/riscv: Remove manual decoding of RV32/64M insn
target/riscv: Remove shift and slt insn manual decoding
target/riscv: make ADD/SUB/OR/XOR/AND insn use arg lists
target/riscv: Move gen_arith_imm() decoding into trans_* functions
target/riscv: Remove manual decoding from gen_store()
target/riscv: Remove manual decoding from gen_load()
target/riscv: Remove manual decoding from gen_branch()
target/riscv: Remove gen_jalr()
target/riscv: Convert quadrant 2 of RVXC insns to decodetree
target/riscv: Convert quadrant 1 of RVXC insns to decodetree
target/riscv: Convert quadrant 0 of RVXC insns to decodetree
target/riscv: Convert RV priv insns to decodetree
target/riscv: Convert RV64D insns to decodetree
target/riscv: Convert RV32D insns to decodetree
target/riscv: Convert RV64F insns to decodetree
target/riscv: Convert RV32F insns to decodetree
target/riscv: Convert RV64A insns to decodetree
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
decodetree handles all instructions now so the fallback is not necessary
anymore.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
with all 16 bit insns moved to decodetree no path is falling back to
gen_system(), so we can remove it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
manual decoding in gen_arith() is not necessary with decodetree. For now
the function is called trans_arith as the original gen_arith still
exists. The former will be renamed to gen_arith as soon as the old
gen_arith can be removed.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
gen_arith_imm() does a lot of decoding manually, which was hard to read
in case of the shift instructions and is not necessary anymore with
decodetree.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
With decodetree we don't need to convert RISC-V opcodes into to MemOps
as the old gen_store() did.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
With decodetree we don't need to convert RISC-V opcodes into to MemOps
as the old gen_load() did.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
We now utilizes argument-sets of decodetree such that no manual
decoding is necessary.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
trans_jalr() is the only caller, so move the code into trans_jalr().
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
we cannot remove the call to gen_arith() in decode_RV32_64G() since it
is used to translate multiply instructions.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
this splits the 64-bit only instructions into its own decode file such
that we generate the decoder for these instructions only for the RISC-V
64 bit target.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
for now only LUI & AUIPC are decoded and translated. If decodetree fails, we
fall back to the old decoder.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Peer Adelt <peer.adelt@hni.uni-paderborn.de>
The current code assumes that we don't need to exit the TB
if a Data Cache Flush or Insert has happend. However, as we
have a shared Data/Instruction TLB, a Data cache flush also
flushes Instruction TLB entries, and a Data cache TLB insert
might also evict a Instruction TLB entry.
So exit the TB in all cases if Instruction translation is enabled.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-11-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-10-svens@stackframe.org>
[rth: Add required tlb flushing when prot id registers change.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The ODE software calls itlbp on existing TLB entries without
calling itlba first, so this seems to be valid.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-9-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
b,gate does GR[t] ← cat(GR[t]{0..29},IAOQ_Front{30..31});
instead of saving the link address to register t.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-8-svens@stackframe.org>
[rth: Move link check outside of ifndef CONFIG_USER_ONLY;
use ctx->privilege; nullify the insn earlier.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
DIAG is usually only used by diagnostics software as it's CPU
specific. In most of the cases it's better to ignore it and log
a message that it's not implemented.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-7-svens@stackframe.org>
[rth: Free the nullify condition.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
HP ODE use rfi to set the Q bit, and i don't see anything in the
documentation that this is forbidden. So remove it.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-6-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
To ease TLB debugging add a few trace events, which are disabled
by default so that there's no performance impact.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-5-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-4-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Assume the following sequence:
pitlbe r0(sr0,r0)
iitlba r4,(sr0,r0)
ldil L%3000000,r5
iitlbp r5,(sr0,r0)
This will purge the whole TLB and add an entry for page 0. However
the current TLB implementation in helper_iitlba() will store to
the last empty TLB entry, while helper_iitlbp() will write to the
first empty entry. That is because an empty entry will match address
0 in helper_iitlba()
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-3-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When one of the source registers is the same as the destination register,
the source register gets overwritten with the destionation value before
do_add_sv() is called, which leads to unexpection condition matches.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190311191602.25796-2-svens@stackframe.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We got away with eliding this check when target/hppa was user-only,
but missed adding this check when adding system support.
Fixes an early crash in the HP-UX 11 installer.
Reported-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
