Currently a direct access to the device structure field is used to connect ISA
device IRQ to the bus. GPIO access should be used instead if possible.
The patch adds wrapper isa_connect_gpio_out. The function connects specified
output GPIO to specified ISA IRQ.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The isa_bus_irqs function initializes ISA bus IRQ array pointer with specified
value.
Previously the ICH9 LPC bridge model did not have its own IRQs but
only IRQ pointer cache. And same GSI were used for ISA bus and other sources
behind the bridge (PCI, SCI). Hence, the pc_q35_init was only possible place to
setup both ISA bus IRQs and the bridge IRQ cache.
As a result, the call of isa_bus_irqs was made from pc_q35_init.
Now the ICH9 LPC bridge has its own output IRQs which are connected to GSI. The
output IRQs are already used to route IRQs from PCI and SCI.
The patch makes the ICH9 LPC bridge output IRQs to used for ISA bus too.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ICH9 LPC bridge has 24 output IRQs connected to GSI. Currently the IRQs are
referenced by pointers. The pointers are initialized at startup by direct access
to the structure fields. This violates Qemu device model.
The patch makes the IRQs handling to use GPIO model.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ich9->pic and ich9->ioapic differ for the first 16 GSIs (because
ich9->pic is wired to 8259+IOAPIC but ich9->ioapic is wired to
IOAPIC only). However, ich9->ioapic is never used for the first
16 GSIs, so the two vectors can be merged.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ich9_lpc_update_pic take care only of GSIs 0-15, and
ich9_lpc_update_apic take care only of GSIs 16-23. Assert
that they are called with the correct GSI indices.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An asserted pirq can be disabled and the corresponding GSIs
should then go down to 0. However, because of the conditional in
ich9_lpc_update_by_pirq, the legacy 8259 pin could remain stuck to 1.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add madt_cpu callback to AcpiDeviceIfClass and use
it for generating LAPIC MADT entries for CPUs.
Later it will be used for generating x2APIC
entries in case of more than 255 CPUs and also
would be reused by ARM target when ACPI CPU hotplug
is introduced there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move all trace-events for files in the hw/isa/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-24-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
it reduces number of args passed in handlers by 1 and
a number of used proxy wrappers saving ~20LOC.
Also it allows to make cpu/mem hotplug code more
universal as it would allow ARM to reuse it without
rewrite by providing its own send_event callback
to trigger events usiong GPIO instead of GPE
as fixed hadrware ACPI model doen't have GPE at all.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
send_event() hook will allow to send ACPI event in
a target specific way (GPE or GPIO based impl.)
it will also simplify proxy wrappers in piix4pm/ich9
that access ACPI regs and SCI which are part of
piix4pm/lcp_ich9 devices and call acpi_foo() API directly.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
exec/cpu-all.h includes qom/cpu.h. Explicit inclusion
will keep things working when cpu.h will not be included
indirectly almost everywhere (either directly or through
qemu-common.h).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
change some "rbca" to "rcrb"(root complex register block) while
the other to "rcba"(root complex base address).
Bonus: add more comments and fix some indentation.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The enable_tco arguments are always true, so they are not needed
anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This will permit to deprecate global DMA_*() functions.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-11-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
isa_bus_irqs(), isa_create() and isa_try_create() call hw_error() when
passed a null bus. Use of hw_error() has always been questionable,
because these are used only during machine initialization, and
printing CPU registers isn't useful there.
Since the previous commit, passing a null bus is a programming error.
Drop the hw_error() and simply let it crash.
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1450354795-31608-12-git-send-email-armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
We can have at most one ISA bus. If you try to create another one,
isa_bus_new() complains to stderr and returns null.
isa_bus_new() is called in two contexts, machine's init() and device's
realize() methods. Since complaining to stderr is not proper in the
latter context, convert isa_bus_new() to Error.
Machine's init():
* mips_jazz_init(), called from the init() methods of machines
"magnum" and "pica"
* mips_r4k_init(), the init() method of machine "mips"
* pc_init1() called from the init() methods of non-q35 PC machines
* typhoon_init(), called from clipper_init(), the init() method of
machine "clipper"
These callers always create the first ISA bus, hence isa_bus_new()
can't fail. Simply pass &error_abort.
Device's realize():
* i82378_realize(), of PCI device "i82378"
* ich9_lpc_realize(), of PCI device "ICH9-LPC"
* pci_ebus_realize(), of PCI device "ebus"
* piix3_realize(), of PCI device "pci-piix3", abstract parent of
"PIIX3" and "PIIX3-xen"
* piix4_realize(), of PCI device "PIIX4"
* vt82c686b_realize(), of PCI device "VT82C686B"
Propagate the error. Note that these devices are typically created
only by machine init() methods with qdev_init_nofail() or similar. If
we screwed up and created an ISA bus before that call, we now give up
right away. Before, we'd hobble on, and typically die in
isa_bus_irqs(). Similar if someone finds a way to hot-plug one of
these critters.
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1450370121-5768-11-git-send-email-armbru@redhat.com>
These are "ICH9-LPC" and "ebus".
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1450370121-5768-10-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1449764955-10741-3-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Commit 4d00636e97 ("ich9: Add the lpc chip", Nov 14 2012) added the
ich9_apm_ctrl_changed() ioport write callback function such that it would
inject the SMI, in response to a write to the APM_CNT register, on the
first CPU, invariably.
Since this register is used by guest code to trigger an SMI synchronously,
the interrupt should be injected on the VCPU that is performing the write.
apm_ioport_writeb() is the .write callback of the "apm_ops"
MemoryRegionOps [hw/isa/apm.c]; it is parametrized to call
ich9_apm_ctrl_changed() by ich9_lpc_init() [hw/isa/lpc_ich9.c], via
apm_init(). Therefore this change affects no other board.
ich9_generate_smi() is an unrelated function that is called by the TCO
watchdog; a watchdog is likely in its right to (asynchronously) inject
interrupts on the first CPU only.
This patch allows the combined edk2/OVMF SMM driver stack to work with
multiple VCPUs on TCG, using both qemu-system-i386 and qemu-system-x86_64.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
This is unused. cpu_exit now is almost exclusively an internal function
to the CPU execution loop. In a few patches, we'll change the remaining
occurrences to qemu_cpu_kick, making it truly internal.
Reviewed-by: Richard henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the signal is sampled high, this indicates that the system is
strapped to the "No Reboot" mode (ICH9 will disable the TCO Timer system
reboot feature). The status of this strap is readable via the NO_REBOOT
bit (CC: offset 0x3410:bit 5).
The NO_REBOOT bit is set when SPKR pin on ICH9 is sampled high. This bit
may be set or cleared by software if the strap is sampled low but may
not override the strap when it indicates "No Reboot".
This patch implements the logic where hardware has ability to set SPKR
pin through a property named "noreboot" and it's sampled high by
default.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This interface provides some registers within a 32-byte range and can be
acessed through PCI-to-LPC bridge interface (PMBASE + 0x60).
It's commonly used as a watchdog timer to detect system lockups through
SMIs that are generated -- if TCO_EN bit is set -- on every timeout. If
NO_REBOOT bit is not set in GCS (General Control and Status register),
the system will be resetted upon second timeout if TCO_RLD register
wasn't previously written to prevent timeout.
This patch adds support to TCO watchdog logic and few other features
like mapping NMIs to SMIs (NMI2SMI_EN bit), system intruder detection,
etc. are not implemented yet.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Q35's ACPI device is hard-coding SMM availability to KVM. Place the
logic where the board is created instead, so that it will be possible
to override it.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These commands are handled entirely by QEMU. Do not raise an SMI
when they happen, because Windows (at least 2008r2) expects these
commands to work and (depending on the value of APMC_EN at
startup) the firmware might not have installed an SMI handler.
When this happens (e.g. the kernel supports SMIs, or you are using
TCG, but you have used "-machine smm=off") RIP is moved to 0x38000
where there is no code to execute.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some convinience fluff: Add support for '-vga virtio', also add
virtio-vga to the list of vga cards so '-device virtio-vga' will
turn off the default vga.
Written by Dave Airlie and Gerd Hoffmann.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add write mask for the smi enable register, so we can disable write
access to certain bits. Open all bits on reset. Disable write access
to GBL_SMI_EN when SMI_LOCK (in ich9 lpc pci config space) is set.
Write access to SMI_LOCK itself is disabled too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Disabling CONFIG_PARALLEL cause removing parallel_hds_isa_init defined in
parallel.c. This function is called during initialization of some boards so
disabling CONFIG_PARALLEL cause build failure.
This patch moves parallel_hds_isa_init to hw/isa/isa-bus.c so it is included
in case of disabled CONFIG_PARALLEL. Build is successful but qemu will abort
with "Unknown device" error when function is called.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Message-Id: <1431509970-32154-1-git-send-email-mrezanin@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This includes pxb support by Marcel, as well as multiple enhancements all over
the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVcC2WAAoJECgfDbjSjVRpwgcH/3mvFP3UmvmXyzf8mYtQ/1fR
ikvdTGHl2DR7TMQszNeCJn/p6NgH3oXRbXh39xM1xl9D2/dsZH9o1cUyFE04K9LK
am0cTmlty1OEyFN8BX1TtpngUxa5mpRA/+NYuWbh1FoTp6RoEPM6P+L1zLqtXYn1
REF++ehrsQI2Az2pibf4nul8bwuTWJLJeMS6TcCVCRGoaHsCESiVMu2sQrzEbWEW
E8ZWaXaiycLxLkW0/oU8BmZyrAk1PHdHwgbMUINV0kV5E2u+ZU+3KY79ezC2FyHW
NV7G9Rhh/5H828/cB6UP4CPZ4AYIYmg02iz5XBGKbd8WS9oPrJVK7EoqfU3oZfc=
=5AmP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, acpi, virtio, tpm
This includes pxb support by Marcel, as well as multiple enhancements all over
the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu Jun 4 11:51:02 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (28 commits)
vhost: logs sharing
hw/acpi: piix4_pm_init(): take fw_cfg object no more
hw/acpi: move "etc/system-states" fw_cfg file from PIIX4 to core
hw/acpi: acpi_pm1_cnt_init(): take "disable_s3" and "disable_s4"
pc-dimm: don't assert if pc-dimm alignment != hotpluggable mem range size
docs: Add PXB documentation
apci: fix PXB behaviour if used with unsupported BIOS
hw/pxb: add numa_node parameter
hw/pci: add support for NUMA nodes
hw/pxb: add map_irq func
hw/pci: inform bios if the system has extra pci root buses
hw/pci: introduce PCI Expander Bridge (PXB)
hw/pci: removed 'rootbus nr is 0' assumption from qmp_pci_query
hw/acpi: remove from root bus 0 the crs resources used by other buses.
hw/acpi: add _CRS method for extra root busses
hw/apci: add _PRT method for extra PCI root busses
hw/acpi: add support for i440fx 'snooping' root busses
hw/pci: extend PCI config access to support devices behind PXB
hw/i386: query only for q35/pc when looking for pci host bridge
hw/pci: made pci_bus_num a PCIBusClass method
...
Conflicts:
hw/i386/pc_piix.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch only modifies the function prototype and updates all chipset
code that calls acpi_pm1_cnt_init() to pass in their own disable_s3 and
disable_s4 settings. vt82c686 is assumed to be fixed "S3 and S4 enabled".
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1204696
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
In DSDT FDC0 declares the IO region as IO(Decode16, 0x03F2, 0x03F2, 0x00, 0x04).
Use the same in lpc_ich9 initialization code.
Now the floppy drive is detected correctly on Windows.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since ich9_lpc_pm_init only requests one irq, so let it just call
qemu_allocate_irq.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Character devices defined with -serial and -parallel are for board
initialization to wire up. Board code examines serial_hds[] and
parallel_hds[] to find them, and creates devices with their qdev
chardev properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a chardev property for board code to set: they use
serial_hds[] (often via qemu_char_get_next_serial()) or parallel_hds[]
in their realize() or init() method to connect to a backend.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is it inconsistent with how the other characrer device models
work (they connect to a backend explicitly identified by a "chardev"
property), it breaks when the backend has been picked up by the board
or a previous -device / device_add already.
Example:
$ qemu-system-ppc64 -M bamboo -S -device i82378 -device pc87312 -device pc87312
qemu-system-ppc64: -device pc87312: Property 'isa-parallel.chardev' can't take value 'parallel0', it's in use
Mark them with suitable FIXME comments.
Cc: Li Guang <lig.fnst@cn.fujitsu.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Drives defined with if!=none are for board initialization to wire up.
Board code calls drive_get() or similar to find them, and creates
devices with their qdev drive properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a drive property for board code to set: they call
driver_get() or drive_get_next() in their realize() or init() method
to implicitly connect to the "next" backend with a certain interface
type.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is this inconsistent with how the other block device models work
(they connect to a backend explicitly identified by a "drive"
property), it breaks when the "next" backend has been picked up by the
board already.
Example:
$ qemu-system-arm -S -M connex -pflash flash.img -device ssi-sd
Aborted (core dumped)
Mark them with suitable FIXME comments.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Memory and CPU hot unplug are both asynchronous procedures.
When the unplug operation happens, unplug request cb is called first.
And when guest OS finished handling unplug, unplug cb will be called
to do the real removal of device.
This patch adds hotunplug cb to ich9, which memory and CPU
hot unplug will use it.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Memory and CPU hot unplug are both asynchronous procedures.
They both need unplug request cb when the unplug operation happens.
This patch adds hotunplug request cb for ich9, and memory and CPU
hot unplug will share it.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Now that isa_mem_base variable is always 0, we can remove its usage.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
piix4 is only used on MIPS Malta board, which gives get_system_memory()
to pci_register_bus().
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Currently, keep current behaviour by always using get_system_memory().
Also use QOM casts when possible.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
superio_ioport_readb can read the 256th element of the array.
Coverity reports an out-of-bounds write in superio_ioport_writeb,
but it does not show the corresponding out-of-bounds read
because it cannot prove that it can happen. Fix the root
cause of the problem (zhanghailang's patch instead fixes
the logic in superio_ioport_writeb).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: qemu-stable@nongnu.org
Refactor superio_ioport_writeb to fix the out of bounds write warning.
In addition, fix two typos: s/chage/change/
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The patch is big, but all it really does is replacing
dinfo->bdrv
by
blk_bs(blk_by_legacy_dinfo(dinfo))
The replacement is repetitive, but the conversion of device models to
BlockBackend is imminent, and will shorten it to just
blk_legacy_dinfo(dinfo).
Line wrapping muddies the waters a bit. I also omit tests whether
dinfo->bdrv is null, because it never is.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Benoît Canet <benoit.canet@nodalink.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
'HotplugHandler.unplug' callback is currently used as async
call to issue unplug request for device that implements it.
Renaming 'unplug' callback to 'unplug_request' should help to
avoid confusion about what callback does and would allow to
introduce 'unplug' callback that would perform actual device
removal when guest is ready for it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Steps:
1.enable qemu debug print, using simply scprit as below:
grep "//#define DEBUG" * -rl | xargs sed -i "s/\/\/#define DEBUG/#define DEBUG/g"
2. make -j
3. get some warning:
hw/i2c/pm_smbus.c: In function 'smb_ioport_writeb':
hw/i2c/pm_smbus.c:142: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/i2c/pm_smbus.c:142: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i2c/pm_smbus.c: In function 'smb_ioport_readb':
hw/i2c/pm_smbus.c:209: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/intc/i8259.c: In function 'pic_ioport_read':
hw/intc/i8259.c:373: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/input/pckbd.c: In function 'kbd_write_command':
hw/input/pckbd.c:232: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/input/pckbd.c: In function 'kbd_write_data':
hw/input/pckbd.c:333: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_writeb':
hw/isa/apm.c:44: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/isa/apm.c:44: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_readb':
hw/isa/apm.c:67: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/timer/mc146818rtc.c: In function 'cmos_ioport_write':
hw/timer/mc146818rtc.c:394: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i386/pc.c: In function 'port92_write':
hw/i386/pc.c:479: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
Fix them.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
imitate nearby code about using '!value' or 'value == NULL'
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
piix_pci.c has been renamed into piix.c at commit
c0907c9e64
update the obsolete reference.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
... using TYPE_ACPI_DEVICE_IF interface.
Which provides status reporting of ACPI declared memory devices
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add memory hotplug initialization/handling to ICH9 LPC device
and enable it by default for post 2.0 machine types
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Propeties of object should be available after its instances_init()
callback is finished and not added in PCIDeviceClass.init which is
roughly corresponds to realize() method.
Moving properties adding into instances_init will fix missing
property error when global/compat property mechanism is used.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
The function is_parallel_epp() is unused; remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
PortioList is an abstraction used for construction of MemoryRegionPortioList
from MemoryRegionPortio. It can be used later to unmap created memory regions.
It also requires proper cleanup because some of the memory inside is allocated
dynamically.
By moving PortioList ot device state we make it possible to cleanup later and
avoid leaking memory.
This change spans several target platforms. The following testcases cover all
changed lines:
qemu-system-ppc -M prep
qemu-system-i386 -vga qxl
qemu-system-i386 -M isapc -soundhw adlib -device ib700,id=watchdog0,bus=isa.0
Signed-off-by: Kirill Batuzov <batuzovk@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KRcc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/qom-devices-for-peter' into staging
QOM infrastructure fixes and device conversions
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
# gpg: Signature made Mon 17 Feb 2014 22:15:37 GMT using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/qom-devices-for-peter: (49 commits)
qtest: Include system headers before user headers
qapi: Refine human printing of sizes
qdev: Use QAPI type names for properties
qdev: Add enum property types to QAPI schema
block: Handle "rechs" and "large" translation options
qdev: Remove hex8/32/64 property types
qdev: Remove most legacy printers
qdev: Use human mode in "info qtree"
qapi: Add human mode to StringOutputVisitor
qdev: Inline qdev_prop_parse()
qdev: Legacy properties are just strings
qdev: Legacy properties are now read-only
qdev: Remove legacy parsers for hex8/32/64
qdev: Sizes are now parsed by StringInputVisitor
qapi: Add size parser to StringInputVisitor
qtest: Don't segfault with invalid -qtest option
ipack: Move IndustryPack out of hw/char/
ipoctal232: QOM parent field cleanup
ipack: QOM parent field cleanup for IPackDevice
ipack: QOM parent field cleanup for IPackBus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Get rid of PCIDevice specific PCIDeviceClass.no_hotplug and use
generic DeviceClass.hotpluggable field instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A VT82C686B southbridge has multiple functions. We model each
function as a separate qdev. One of them need some special wiring set
up in mips_fulong2e_init() to work: the ISA bridge at 05.0.
The IDE controller at 05.1 (via-ide) has always had
cannot_instantiate_with_device_add_yet set, but there is no obvious
reason why device_add could not work for them. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
A PIIX3/PIIX4 southbridge has multiple functions. We model each
function as a separate qdev. Two of them need some special wiring set
up in pc_init1() or mips_malta_init() to work: the ISA bridge at 01.0,
and the SMBus controller at 01.3.
The IDE controller at 01.1 (piix3-ide, piix3-ide-xen, piix4-ide) has
always had cannot_instantiate_with_device_add_yet set, but there is no
obvious reason why device_add could not work for them. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
An ICH9 southbridge contains several PCI devices, some of them with
multiple functions. We model each function as a separate qdev. Two
of them need some special wiring set up in pc_q35_init() to work: the
LPC controller at 00:1f.0, and the SMBus controller at 00:1f.3.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds APIs that will be used to fill in
acpi tables, implemented using QOM,
to various ich9 components.
Some information is still missing in QOM,
so we fall back on lookups by type instead.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- i82378 only exists on PCI bus; do not split implementation in 2 structs
- remove BARs, which are not specified in datasheet
- replace custom isa_mmio implementation by PCI bus IO region usage
- use QOM casts when required
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[AF: Style- and QOM-related changes, dropped no_user, reverted VMSD name]
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Currently, it is done by i82378 PCI-ISA bridge, which shouldn't
care about it.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It is not used anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-15-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move next_cpu from CPU_COMMON to CPUState.
Move first_cpu variable to qom/cpu.h.
gdbstub needs to use CPUState::env_ptr for now.
cpu_copy() no longer needs to save and restore cpu_next.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Rebased, simplified cpu_copy()]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This new API will avoid having too many memory_region_ref/unref
in paths that currently use memory_region_find.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Open-code isa_is_ioport_assigned via a memory region lookup. As all IO
ports are now directly or indirectly registered via the memory API, this
becomes possible and will finally allow us to drop the ioport tables.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert over to memory regions to obsolete register_ioport*.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop ISADeviceClass::init and the resulting no-op initfn and let
children implement their own realizefn. Adapt error handling.
Split off an instance_init where sensible.
Signed-off-by: Andreas Färber <afaerber@suse.de>
