The se7751 was still doing the PCI fixups in its own board directory,
so we move it over to arch/sh/drivers/pci/ with the rest of the board
fixups. It has bitrotted significantly over the years, so will still
likely need a bit of work to bring back up to date.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the similar sort of scheme that the refactored SH7780 code
uses, using a 64MB CS3 mapping to handle the window0 case, and simply
discarding window1. This vastly simplifies the code, and allows most of
the board-specific setup to go die.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These fixups seem to have bitrotted a bit since their introduction in the
2.4 days. As we never had much use for them in the first place, and
nothing is using them any more, kill them off the rest of the way.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This isn't a real BAR, so prevent any attempts to move it, as we don't
wish to encourage a bus luck by overzealous PCI initialization code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the remaining common bits in to pci-lib. Thereby reducing
pci.c/pci-new.c to simple bus fixups and controller registration.
As more platforms are moved over, the old code will disappear completely
and the pci-new bits will be rolled in to pci-lib, eventually replacing
pci.c completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the io and mem offsets are tracked accordingly, the pci-new
version of the bus<->resource mappers can be used generically. This
moves them in to pci-lib.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves off of the board_pci_channels[] approach for bus registration
and over to a cleaner register_pci_controller(), all derived from the
MIPS code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all PCI channels have non-translatable memory windows, this is a
special property of the on-chip PCIC with its 0xfd00... mapping, handle
this explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the pci_iomap() definitions and reworks how the I/O
port base is handled. PCI channels can register their own I/O map base,
or if none is provided, the system-wide generic I/O base is used instead.
Functionally nothing changes, while this allows us to kill off lots of
I/O address special casing and lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is left over cruft that hasn't been used by anything in a long time,
kill off bits that weren't purged previously.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces a saner pcibios_align_resource() that can be used
regardless of whether pci-auto or pci-new are being used, and
consolidates it in pci-lib.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits off a 'pci-new.c' which is aimed at gradually replacing the
pci-auto backend and the arch/sh/drivers/pci/pci.c core respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new PCI code wants its own bus<->resource mappings instead of the
generic equivalents, so drop the asm-generic include in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This starts moving out the common initialization bits from the various
fixup paths in to the shared init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the platform code is a bit leaner, we can start consolidating
the various IRQ routing implementations. There are effectively only 2
variants, and the others can use those directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 68b42d1b54 ("sh: sh7785lcr: Map
whole PCI address space.") changed around the semantics of how various
chip-selects are made accessible to PCI. Now that there is a single
large mapping covering from CS0-CS6, there is no longer any need to
do multi-window mapping. Subsequently, all of the differing
implementations can be consolidated in to pci-sh7780.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the PCI I/O and memory window definitions across
the pci-sh7780 users in pci-sh7780 itself. No functional changes, in that
every platform had exactly the same implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the I/O port base isn't being set anywhere, which allows things
like generic_inl() to blow up. Fix this up to point at the PCI IO window.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCIC contains a read-only cache line size register that we can
derive pci_cache_line_size from. So, make sure that the software idea of
the cache line size actually matches the host controller's idea.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Don't use pci_write_reg() for these, as it defaults to 32-bit. Rather
than using the helper, use __raw_writeb() directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks how the host controller is probed, and makes it a bit more
verbose in the event a new type of controller is detected. Additionally,
we also log the revision information.
This now uses the proper access sizes for the vendor/device registers,
rather than relying on a larger access that encapsulated both of them.
Not all devices support 32-bit read cycles for these registers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCI host controller implements a configuration header that
requires a fair bit of hand-holding to initialize properly. By default
it appears as a pre-2.0 host controller given the zeroed out class code,
so fix this up properly.
Some boards that happened to be using the R7780RP version of the PCIC
fixups had set this correctly, but this belongs in the standard
initialization, and is by no means board specific.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
P1SEGADDR is obsolete and will be killed off completely in the future,
so transition off of it and reference P1SEG explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SE7780 has the same PCIC fixup as SDK7780, and SH7785LCR the same
as R7780RP. Switch to using those, and drop the duplicate code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With board_pci_channels now being exported in a single place, update the
boards that duplicated the export.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of sometimes exporting board_pci_channels[] in the board specific
code just export it in one place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the io window base address in struct pci_channel and use that one
instead of SH77xx_PCI_IO_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the base address of the pci host controller registers in struct
pci_channel and use the address in pci_read_reg() and pci_write_reg().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store a struct pci_channel pointer in bus->sysdata. This makes whatever
struct pci_channel assigned to a bus available for sh4_pci_read() and
sh4_pci_write(). We also modify PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to
use bus->sysdata - this to gives us support for multiple pci channels.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replaces PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM with direct struct
pci_channel access. This allows us to have more than one pci
channel.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
