At the moment we try and replenish the receive ring on every rx interrupt.
We even have a pool->threshold but aren't using it.
To limit the maximum latency incurred when refilling, change the threshold
from 1/2 to 7/8 and reduce the largest rx pool from 768 buffers to 512 which
should be more than enough.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some modulus operators with an increment and compare to avoid
an integer divide.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cause TIPC to return EAGAIN if it is unable to enable a new Ethernet
bearer because one or more recently disabled Ethernet bearers are
temporarily consuming resources during shut down. (The previous error
code, EDQUOT, is now returned only if all available Ethernet bearer
data structures are fully enabled at the time the request to enable an
additional bearer is received.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to expand the headroom of an outgoing TIPC message if the
sk_buff has insufficient room to hold the header for the associated
Ethernet device. This change is necessary to ensure that messages
TIPC does not create itself (eg. incoming messages that are being
routed to another node) do not cause problems, since TIPC has no
control over the amount of headroom available in such messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimizes TIPC's name table translation code to avoid unnecessary
manipulation of the node address field of the resulting port id when
name translation fails. This change is possible because a valid port
id cannot have a reference field of zero, so examining the reference
only is sufficient to determine if the translation was successful.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change several wan drivers to make strings and other initialize
only parameters const.
Compile tested only (with no new warnings)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While porting GRO to r8169, I found this driver has a bug in its rx
path.
All skbs given to network stack had their ip_summed set to
CHECKSUM_NONE, while hardware said they had correct TCP/UDP checksums.
The reason is driver sets skb->ip_summed on the original skb before the
copy eventually done by copybreak. The fresh skb gets the ip_summed =
CHECKSUM_NONE value, forcing network stack to recompute checksum, and
preventing my GRO patch to work.
Fix is to make the ip_summed setting after skb copy.
Note : rx_copybreak current value is 16383, so all frames are copied...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call flush_workqueue() on the cxgb3 Work Queue in cxgb_down() when
we're being called from the fatal error task ... which is executing on the
cxgb3 Work Queue.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Platform code needs to deal with them now.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__alloc_skb() uses a memset() to clear all the beginning of skb,
including bitfields contained in 'flags1' & 'flags2'.
We dont need any more to use kmemcheck_annotate_bitfield() on these
fields. However, we still need it for the clone part, which is not
cleared.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tulip_private is a bit large (order-1 allocation even on 32bit
arch), try to shrink it, remove its net_device_stats field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation for recent changes to the tunables accept_ra and
forwarding.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to accepting router advertisement, the IPv6 stack does not send router
solicitations if forwarding is enabled.
This patch enables this behavior to be overruled by setting forwarding to the
special value 2.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IPv6 behavior is to not accept router advertisements while
forwarding, i.e. configured as router.
This does make sense, a router is typically not supposed to be auto
configured. However there are exceptions and we should allow the
current behavior to be overwritten.
Therefore this patch enables the user to overrule the "if forwarding
enabled then don't listen to RAs" rule by setting accept_ra to the
special value of 2.
An alternative would be to ignore the forwarding switch alltogether
and solely accept RAs based on the value of accept_ra. However, I
found that if not intended, accepting RAs as a router can lead to
strange unwanted behavior therefore we it seems wise to only do so
if the user explicitely asks for this behavior.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_stats() method incorrectly clears a global array before folding
various stats. This can break SNMP applications.
Switch to 64 bit flavor to work on a user supplied buffer, and provide
64bit counters even on 32bit arches.
Fix a bug in bnad_netdev_hwstats_fill(), for rx_fifo_errors, missing a
folding (only the last counter was taken into account)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the code up according to Documentation/CodingStyle.
Don't initialize the variable dont_send in arp_process().
Remove the temporary varialbe flags in arp_state_to_flags().
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a small helper ptype_head() to get the head to manipulate
dev_add_pack() & __dev_remove_pack() can use a spinlock without
blocking BH, since softirq use RCU, and these functions are run from
process context only.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct state range of PHY bus addresses (i.e. 0-31) in comment,
make spelling of PHY consistent in comments.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correctly the in_pkts packet counter also for SCTP
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dma_addr_t 64-bit case for powerpc with 64-bit phys addresses.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Ilpo Jarvinen, this updates also the initial window
setting for tcp_output with regard to RFC 5681.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/pxa168_eth.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the hardware scan handler could access an invalid scan request
structure. The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(skb->data - skb->head) can be changed by skb_headroom(skb)
Remove some uses of NET_SKBUFF_DATA_USES_OFFSET, using
(skb_end_pointer(skb) - skb->head) or
(skb_tail_pointer(skb) - skb->head) : compiler does the right thing,
and this is more readable for us ;)
(struct skb_shared_info *) casts in pskb_expand_head() to help memcpy()
to use aligned moves.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- napi_gro_flush() is exported from net/core/dev.c, to avoid
an irq_save/irq_restore in the packet receive path.
- use napi_gro_receive() instead of netif_receive_skb()
- use napi_gro_flush() before calling __napi_complete()
- turn on NETIF_F_GRO by default
- Tested on a Marvell 88E8001 Gigabit NIC
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a call to of_node_put in the error handling code following a call to
of_find_matching_node.
This patch also moves the existing call to of_node_put after the call to
iounmap in the error handling code, to make it possible to jump to
of_node_put without doing iounmap. These appear to be disjoint operations,
so the ordering doesn't matter.
This patch furthermore changes the -ENODEV result in the error handling
code for of_find_matching_node to a return of 0, as found in the error
handling code for of_iomap, because the return type of the function is
unsigned.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1,E2;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
|of_find_node_by_type
|of_find_node_with_property
|of_find_matching_node
|of_parse_phandle
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
(
E2 = x;
|
of_node_put(x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper routine to disable chip interrupts.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tunnel4_handlers, tunnel64_handlers, tunnel6_handlers and
tunnel46_handlers are protected by RCU, but we dont use appropriate rcu
primitives to scan them. rcu_lock() is already held by caller.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.52.53-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BCM84823 to the supported PHYs
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 848xx LED configuration according to the new microcode (Boards
were shipped with only with the new microcode)
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded setting of XAUI low power to BCM8727. This was required
only in older microcode which is not in the field.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change BCM848xx behavior to fit IEEE such that setting 10Mb/100Mb will
use force speed, and setting 1Gb/10Gb will use auto-negotiation with the
specific speed advertised
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset link before any new link settings to avoid potential link issue
caused by previous link settings
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In BCM8727 based boards, setting default 10G link speed after link was
set to 1G may lead to link down issue. The problem was setting the right
value, but to the wrong registers
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix potential link issue caused by insufficient delay time during SPIROM
load of BCM8073/BCM8727
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o New CKSUM flag added by fw to notify cksum is verified.
o Update version to 5.0.9
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor allows, two VM's interfaces to have same mac address.
These VM's interfaces get differentiate with Vlan tag.
This patch add support to learn and configure mac+vlan filter on device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device eswitch need to configure with VM's mac address.
Hypervisor doesn't provide any utility/callbacks to get VM's mac address.
Unicast mac address filter improves performance and also provide
packet loopback capability i.e communication between VM.
Above features is by default off, can be turned on with module parameter
'mac_learn'.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Rename mac_learning to mac_override
o Added check in set_mac to return error if mac override is disabled.
o Disabling mac_override only supported for Non priviledged functions.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
