Allow a BlockFrequency to be divided by a non-zero BranchProbability
with saturating arithmetic. This will be used to compute the frequency
of a loop header given the probability of leaving the loop.
Our long division algorithm already saturates on overflow, so that was a
freebie.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185184 91177308-0d34-0410-b5e6-96231b3b80d8
Fix ABI handling for function
returning bool -- use st.param.b32 to return the value
and use ld.param.b32 in caller to load the return value.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185177 91177308-0d34-0410-b5e6-96231b3b80d8
This patch assigns paired GPRs for inline asm with
64-bit data on ARM. It's enabled for both ARM and Thumb to support modifiers
like %H, %Q, %R.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185169 91177308-0d34-0410-b5e6-96231b3b80d8
sys::fs::unique_file will now loop infinitely if provided with a file name
without '%' characters and the input file already exists. As a result, bugpoint
cannot use a fixed file name for the execution output (including the reference
output).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185166 91177308-0d34-0410-b5e6-96231b3b80d8
I used the class to safely reset the state of the builder's debug location. I
think I have caught all places where we need to set the debug location to a new
one. Therefore, we can replace the class by a function that just sets the debug
location.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185165 91177308-0d34-0410-b5e6-96231b3b80d8
We were generating intrinsics for NEON fixed-point conversions that didn't
exist (e.g. float -> i16). There are two cases to consider:
+ iN is smaller than float. In this case we can do the conversion but need an
extend or truncate as well.
+ iN is larger than float. In this case using the NEON conversion would be
incorrect so we don't perform any combining.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185158 91177308-0d34-0410-b5e6-96231b3b80d8
The mapping between SRS pseudo-instructions and SRS native instructions was incorrect, the correct mapping is:
srsfa -> srsib
srsea -> srsia
srsfd -> srsdb
srsed -> srsda
This fixes <rdar://problem/14214734>.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185155 91177308-0d34-0410-b5e6-96231b3b80d8
No functionality change.
It should suffice to check the type of a debug info metadata, instead of
calling Verify. For cases where we know the type of a DI metadata, use
assert.
Also update testing cases to make them conform to the format of DI classes.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185135 91177308-0d34-0410-b5e6-96231b3b80d8
* Don't try to create parent directories in unique_file. It had two problem:
* It violates the contract that it is atomic. If the directory creation
success and the file creation fails, we would return an error but the
file system was modified.
* When creating a temporary file clang would have to first check if the
parent directory existed or not to avoid creating one when it was not
supposed to.
* More efficient implementations of createUniqueDirectory and the unique_file
that produces only the file name. Now all 3 just call into a static
function passing what they want (name, file or directory).
Clang also has to be updated, so tests might fail if a bot picks up this commit
and not the corresponding clang one.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185126 91177308-0d34-0410-b5e6-96231b3b80d8
This reverts commit r185099.
Looks like both the ppc-64 and mips bots are still failing after I reverted this
change.
Since:
1. The mips bot always performs a clean build,
2. The ppc64-bot failed again after a clean build (I asked the ppc-64
maintainers to clean the bot which they did... Thanks Will!),
I think it is safe to assume that this change was not the cause of the failures
that said builders were seeing. Thus I am recomitting.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185111 91177308-0d34-0410-b5e6-96231b3b80d8
This reverts commit r185095. This is causing a FileCheck failure on
the 3dnow intrinsics on at least the mips/ppc bots but not on the x86
bots.
Reverting while I figure out what is going on.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185099 91177308-0d34-0410-b5e6-96231b3b80d8
The category which an APFloat belongs to should be dependent on the
actual value that the APFloat has, not be arbitrarily passed in by the
user. This will prevent inconsistency bugs where the category and the
actual value in APFloat differ.
I also fixed up all of the references to this constructor (which were
only in LLVM).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185095 91177308-0d34-0410-b5e6-96231b3b80d8
algorithm when assigning EnumValues to the synthesized registers.
The current algorithm, LessRecord, uses the StringRef compare_numeric
function. This function compares strings, while handling embedded numbers.
For example, the R600 backend registers are sorted as follows:
T1
T1_W
T1_X
T1_XYZW
T1_Y
T1_Z
T2
T2_W
T2_X
T2_XYZW
T2_Y
T2_Z
In this example, the 'scaling factor' is dEnum/dN = 6 because T0, T1, T2
have an EnumValue offset of 6 from one another. However, in other parts
of the register bank, the scaling factors are different:
dEnum/dN = 5:
KC0_128_W
KC0_128_X
KC0_128_XYZW
KC0_128_Y
KC0_128_Z
KC0_129_W
KC0_129_X
KC0_129_XYZW
KC0_129_Y
KC0_129_Z
The diff lists do not work correctly because different kinds of registers have
different 'scaling factors'. This new algorithm, LessRecordRegister, tries to
enforce a scaling factor of 1. For example, the registers are now sorted as
follows:
T1
T2
T3
...
T0_W
T1_W
T2_W
...
T0_X
T1_X
T2_X
...
KC0_128_W
KC0_129_W
KC0_130_W
...
For the Mips and R600 I see a 19% and 6% reduction in size, respectively. I
did see a few small regressions, but the differences were on the order of a
few bytes (e.g., AArch64 was 16 bytes). I suspect there will be even
greater wins for targets with larger register files.
Patch reviewed by Jakob.
rdar://14006013
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185094 91177308-0d34-0410-b5e6-96231b3b80d8
The purpose of this test was to check boundary conditions for the size
of an ALU clause. This test is very sensitive to changes to the
optimizer or scheduler, because it requires an exact number of ALU
instructions in order to remain valid. It's not good to have a test
this sensitive, because it is confusing to developers who implement
optimizations and then 'break' the test.
I'm not sure if there is a good way to test these limits using lit, but
if I can come up with replacement test that isn't as sensitive I'll add
it back to the tree.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185084 91177308-0d34-0410-b5e6-96231b3b80d8
Use vectorized instruction instead of original instruction anchored in the
original loop.
Fixes PR16452 and t2075.c of PR16455.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185081 91177308-0d34-0410-b5e6-96231b3b80d8
