Move get/set_r13_banked() from helper.c to op_helper.c. This will
let us add exception-raising code to them, and also puts them
in the same file as get/set_user_reg(), which makes some conceptual
sense.
(The original reason for the helper.c/op_helper.c split was that
only op_helper.c had access to the CPU env pointer; this distinction
has not been true for a long time, though, and so the split is
now rather arbitrary.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
The SRS instruction is:
* UNDEFINED in Hyp mode
* UNPREDICTABLE in User or System mode
* UNPREDICTABLE if the specified mode isn't accessible
* trapped to EL3 if EL3 is AArch64 and we are at Secure EL1
Clean up the code to handle all these cases cleanly, including
picking UNDEF as our choice of UNPREDICTABLE behaviour rather
blindly trusting the mode field passed in the instruction.
As part of this, move the check for IS_USER into gen_srs()
itself rather than having it done by the caller.
The exception is that we don't UNDEF for calls from System
mode, which need a runtime check. This will be dealt with in
the following commits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
If access to FPEXC32_EL2 is trapped by CPTR_EL2.TFP or CPTR_EL3.TFP,
this should be reported with a syndrome register indicating an
FP access trap, not one indicating a system register access trap.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Implement the debug register traps controlled by MDCR_EL2.TDA
and MDCR_EL3.TDA.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Implement trapping of the "debug ROM" registers, which are controlled
by MDCR_EL2.TDRA for EL2 but by the more general MDCR_EL3.TDA for EL3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Implement the traps to EL2 and EL3 controlled by the bits
MDCR_EL2.TDOSA MDCR_EL3.TDOSA. These can configurably trap
accesses to the "powerdown debug" registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
We weren't quite implementing the handling of SCR.SMD correctly.
The condition governing whether the SMD bit should apply only
for NS state is "is EL3 is AArch32", not "is the current EL AArch32".
Fix the condition, and clarify the comment both to reflect this and
to expand slightly on what's going on for the v7-no-Virtualization case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Correct some corner cases we were getting wrong for
CNTFRQ access rights:
* should UNDEF from 32-bit Secure EL1
* only writable from the highest implemented exception level,
which might not be EL1 now
To clarify the code, provide a new utility function
arm_highest_el() which returns the highest implemented
exception level.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Currently accumulated patches for target-ppc, pseries machine type and
related devices.
* Some cleanups to management of SDR1 and the hashed page table
* Implementations of a number of simple PAPR hypercalls
* Significant improvements to the Macintosh CUDA device
* Several bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YxlE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.6-20160218' into staging
ppc patch queue for 2016-02-18
Currently accumulated patches for target-ppc, pseries machine type and
related devices.
* Some cleanups to management of SDR1 and the hashed page table
* Implementations of a number of simple PAPR hypercalls
* Significant improvements to the Macintosh CUDA device
* Several bugfixes
# gpg: Signature made Thu 18 Feb 2016 04:16:51 GMT using RSA key ID 20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.6-20160218: (26 commits)
hw/ppc/spapr: Halt CPU when powering off via RTAS call
pseries: Include missing pseries-2.5 compat properties in pseries-2.4
cuda: remove CUDA_GET_SET_IIC/CUDA_COMBINED_FORMAT_IIC commands
cuda: remove GET_6805_ADDR command
cuda: port SET_TIME command to new framework
cuda: port GET_TIME command to new framework
cuda: port SET_POWER_MESSAGES command to new framework
cuda: port FILE_SERVER_FLAG command to new framework
cuda: port RESET_SYSTEM command to new framework
cuda: port POWERDOWN command to new framework
cuda: port SET_DEVICE_LIST command to new framework
cuda: port SET_AUTO_RATE command to new framework
cuda: port AUTOPOLL command to new framework
cuda: move unknown commands reject out of switch
cuda: add a framework to handle commands
hw/ppc/spapr: Implement the h_set_xdabr hypercall
hw/ppc/spapr: Implement h_set_dabr
hw/ppc/spapr: Add h_set_sprg0 hypercall
migration: ensure htab_save_first completes after timeout
target-ppc: Remove hack for ppc_hash64_load_hpte*() with HV KVM
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The LoPAPR specification defines the following for the RTAS
power-off call: "On successful operation, does not return".
However, the implementation in QEMU currently returns and runs
the guest CPU again for some more cycles. This caused some
trouble with the new ppc implementation of the kvm-unit-tests
recently. So let's make sure that the QEMU implementation
follows the spec, thus stop the CPU to make sure that the
RTAS call does not return to the guest anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4b23699 "pseries: Add pseries-2.6 machine type" added a new
SPAPR_COMPAT_2_5 macro in the usual way. However, it didn't add this
macro to the existing SPAPR_COMPAT_2_4 macro so that pseries-2.4
inherits newer compatibility properties which are needed for 2.5 and
earlier.
This corrects the oversight.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
We currently don't emulate the I2C bus provided by CUDA.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It doesn't seem to be used, and operating systems should accept a 'unknown command' answer.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This command tells if computer should automatically wake-up after a power loss.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also implement the command, by taking device list mask into account
when polling ADB devices.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also implement the command, by removing the hardcoded period of 20 ms/50 Hz
and replacing it by the one requested by user.
Update VMState version to store this new parameter.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Next commits will port existing CUDA commands to this framework.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SET_XDABR hypercall is similar to H_SET_DABR, but also sets
the extended DABR (DABRX) register.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to LoPAPR, h_set_dabr should simply set DABRX to 3
(if the register is available), and load the parameter into DABR.
If DABRX is not available, the hypervisor has to check the
"Breakpoint Translation" bit of the DABR register first.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a very simple hypercall that only sets up the SPRG0
register for the guest (since writing to SPRG0 was only permitted
to the hypervisor in older versions of the PowerISA).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
htab_save_first_pass could return without finishing its work due to
timeout. The patch checks if another invocation of it is necessary and
will call it in htab_save_complete if necessary.
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[removed overlong line]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With HV KVM, the guest's hash page table (HPT) is managed by the kernel and
not directly accessible to QEMU. This means that spapr->htab is NULL
and normally env->external_htab would also be NULL for each cpu.
However, that would cause ppc_hash64_load_hpte*() to do the wrong thing in
the few cases where QEMU does need to load entries from the in-kernel HPT.
Specifically, seeing external_htab is NULL, they would look for an HPT
within the guest's address space instead.
To stop that we have an ugly hack in the pseries machine type code to
set external htab to (void *)1 instead.
This patch removes that hack by having ppc_hash64_load_hpte*() explicitly
check kvmppc_kern_htab instead, which makes more sense.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At the moment the size of the hash page table (HPT) is fixed based on the
maximum memory allowed to the guest. As such, we allocate the table during
machine construction, and just clear it at reset.
However, we're planning to implement a PAPR extension allowing the hash
page table to be resized at runtime. This will mean that on reset we want
to revert it to the default size. It also means that when migrating, we
need to make sure the destination allocates an HPT of size matching the
host, since the guest could have changed it before the migration.
This patch replaces the spapr_alloc_htab() and spapr_reset_htab() functions
with a new spapr_reallocate_hpt() function. This is called at reset and
inbound migration only, not during machine init any more.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At present we calculate the recommended hash page table (HPT) size for a
pseries guest just once in ppc_spapr_init() before allocating the HPT.
In future patches we're going to want this calculation in other places, so
this splits it out into a helper function. While we're at it, change the
calculation to use ctz() instead of an explicit loop.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When migrating the 'pseries' machine type with KVM, we use a special fd
to access the hash page table stored within KVM. Usually, this fd is
opened at the beginning of migration, and kept open until the migration
is complete.
However, if there is a guest reset during the migration, the fd can become
stale and we need to re-open it. At the moment we use an 'htab_fd_stale'
flag in sPAPRMachineState to signal this, which is checked in the migration
iterators.
But that's rather ugly. It's simpler to just close and invalidate the
fd on reset, and lazily re-open it in migration if necessary. This patch
implements that change.
This requires a small addition to the machine state's instance_init,
so that htab_fd is initialized to -1 (telling the migration code it
needs to open it) instead of 0, which could be a valid fd.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
The HMP command "info registers" produces somewhat different information on
different ppc cpu variants. For those with a hash MMU it's supposed to
include the SDR1, DAR and DSISR registers related to the MMU. However,
the switch is missing a couple of MMU model variants, meaning we will
miss out this information on certain CPUs which should have it.
This patch corrects the oversight. (Really these MMU model IDs need a big
cleanup, but we might as well fix the bug in the interim).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
This KVM stub implementation isn't used anywhere.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
* qemu-char fixes from Daniel and Marc-André
* Bug fixes that break qemu-iotests
* Changes to fix reset from panicked state
* checkpatch false positives for designated initializers
* TLS support in the NBD servers and clients
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWw03lAAoJEL/70l94x66D/0MH/3Nctz5y1GKgAX0i6rKErV3/
hvPt6JHdWd7uBtowzO5kOy3fyOnVVST6jNHMQPAmJplUC40s6Ca0hycw9TjdJUdu
ULq0Ba7tQ1TAXowDqibtEn+iTkzSrocTJLfEglNscKzJ4y5w0vc5Bt5PgPB65mbn
oTo/YR8KyRWS6rXjyNnKb0PCaYEQziBndjuIxp9yJUsLcw1UgQJVcrUNEIiciOWu
SlWDxvJJQt5cCrTPnUXeBdjJVGaLxbcpe2llEJnIuf6Pjq4u7J0y+DJ40y0DCi9q
v3V4r16HhAGmBZNIlCtbClfhb/sRTVhONQiS9ehhROo8QCaL1psc11HWvMJ0tx0=
=CDoZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Coverity fixes for IPMI and mptsas
* qemu-char fixes from Daniel and Marc-André
* Bug fixes that break qemu-iotests
* Changes to fix reset from panicked state
* checkpatch false positives for designated initializers
* TLS support in the NBD servers and clients
# gpg: Signature made Tue 16 Feb 2016 16:27:17 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
nbd: enable use of TLS with nbd-server-start command
nbd: enable use of TLS with qemu-nbd server
nbd: enable use of TLS with NBD block driver
nbd: implement TLS support in the protocol negotiation
nbd: use "" as a default export name if none provided
nbd: always query export list in fixed new style protocol
nbd: allow setting of an export name for qemu-nbd server
nbd: make client request fixed new style if advertised
nbd: make server compliant with fixed newstyle spec
nbd: invert client logic for negotiating protocol version
nbd: convert to using I/O channels for actual socket I/O
nbd: convert blockdev NBD server to use I/O channels for connection setup
nbd: convert qemu-nbd server to use I/O channels for connection setup
nbd: convert block client to use I/O channels for connection setup
qemu-nbd: add support for --object command line arg
qom: add helpers for UserCreatable object types
ipmi: sensor number should not exceed MAX_SENSORS
mptsas: fix wrong formula
mptsas: fix memory leak
mptsas: add missing va_end
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This modifies the nbd-server-start QMP command so that it
is possible to request use of TLS. This is done by adding
a new optional parameter "tls-creds" which provides the ID
of a previously created QCryptoTLSCreds object instance.
TLS is only supported when using an IPv4/IPv6 socket listener.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-17-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This modifies the qemu-nbd program so that it is possible to
request the use of TLS with the server. It simply adds a new
command line option --tls-creds which is used to provide the
ID of a QCryptoTLSCreds object previously created via the
--object command line option.
For example
qemu-nbd --object tls-creds-x509,id=tls0,endpoint=server,\
dir=/home/berrange/security/qemutls \
--tls-creds tls0 \
--exportname default
TLS requires the new style NBD protocol, so if no export name
is set (via --export-name), then we use the default NBD protocol
export name ""
TLS is only supported when using an IPv4/IPv6 socket listener.
It is not possible to use with UNIX sockets, which includes
when connecting the NBD server to a host device.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-16-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This modifies the NBD driver so that it is possible to request
use of TLS. This is done by providing the 'tls-creds' parameter
with the ID of a previously created QCryptoTLSCreds object.
For example
$QEMU -object tls-creds-x509,id=tls0,endpoint=client,\
dir=/home/berrange/security/qemutls \
-drive driver=nbd,host=localhost,port=9000,tls-creds=tls0
The client will drop the connection if the NBD server does not
provide TLS.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-15-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This extends the NBD protocol handling code so that it is capable
of negotiating TLS support during the connection setup. This involves
requesting the STARTTLS protocol option before any other NBD options.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-14-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the user does not provide an export name and the server
is running the new style protocol, where export names are
mandatory, use "" as the default export name if the user
has not specified any. "" is defined in the NBD protocol
as the default name to use in such scenarios.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-13-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the new style protocol, the NBD client will currenetly
send NBD_OPT_EXPORT_NAME as the first (and indeed only)
option it wants. The problem is that the NBD protocol spec
does not allow for returning an error message with the
NBD_OPT_EXPORT_NAME option. So if the server mandates use
of TLS, the client will simply see an immediate connection
close after issuing NBD_OPT_EXPORT_NAME which is not user
friendly.
To improve this situation, if we have the fixed new style
protocol, we can sent NBD_OPT_LIST as the first option
to query the list of server exports. We can check for our
named export in this list and raise an error if it is not
found, instead of going ahead and sending NBD_OPT_EXPORT_NAME
with a name that we know will be rejected.
This improves the error reporting both in the case that the
server required TLS, and in the case that the client requested
export name does not exist on the server.
If the server does not support NBD_OPT_LIST, we just ignore
that and carry on with NBD_OPT_EXPORT_NAME as before.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-12-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu-nbd server currently always uses the old style protocol
since it never sets any export name. This is a problem because
future TLS support will require use of the new style protocol
negotiation.
This adds "--exportname NAME" / "-x NAME" arguments to qemu-nbd
which allow the user to set an explicit export name. When an
export name is set the server will always use the new style
NBD protocol.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-11-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the server advertises support for the fixed new style
negotiation, the client should in turn enable new style.
This will allow the client to negotiate further NBD
options besides the export name.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-10-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the client does not request the fixed new style protocol,
then we should only accept NBD_OPT_EXPORT_NAME. All other
options are only valid when fixed new style has been activated.
The qemu-nbd client doesn't currently request fixed new style
protocol, but this change won't break qemu-nbd, because it
fortunately only ever uses NBD_OPT_EXPORT_NAME, so was never
triggering the non-compliant server behaviour.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-9-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The nbd_receive_negotiate() method takes different code
paths based on whether 'name == NULL', and then checks
the expected protocol version in each branch.
This patch inverts the logic, so that it takes different
code paths based on what protocol version it receives and
then checks if name is NULL or not as needed.
This facilitates later code which allows the client to
be capable of using the new style protocol regardless
of whether an export name is listed or not.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-8-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all callers are converted to use I/O channels for
initial connection setup, it is possible to switch the core
NBD protocol handling core over to use QIOChannel APIs for
actual sockets I/O.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-7-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This converts the blockdev NBD server to use the QIOChannelSocket
class for initial listener socket setup and accepting of client
connections. Actual I/O is still being performed against the
socket file descriptor using the POSIX socket APIs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-6-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This converts the qemu-nbd server to use the QIOChannelSocket
class for initial listener socket setup and accepting of client
connections. Actual I/O is still being performed against the
socket file descriptor using the POSIX socket APIs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-5-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This converts the NBD block driver client to use the QIOChannelSocket
class for initial connection setup. The NbdClientSession struct has
two pointers, one to the master QIOChannelSocket providing the raw
data channel, and one to a QIOChannel which is the current channel
used for I/O. Initially the two point to the same object, but when
TLS support is added, they will point to different objects.
The qemu-img & qemu-io tools now need to use MODULE_INIT_QOM to
ensure the QIOChannel object classes are registered. The qemu-nbd
tool already did this.
In this initial conversion though, all I/O is still actually done
using the raw POSIX sockets APIs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1455129674-17255-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
