Spec on UHCI_STS_USBERR: "If the TD on which the error interrupt
occurred also had its IOC bit set, both this bit and Bit 0 are set."
Make UHCI emulation do that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add ich9 controllers, Factor out properties to a separate
struct and reference it to reduce duplication.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To use as a companion controller set the masterbus property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Note this fixes 2 things in one go, first of all the device_destroy bus
op should be a device_detach bus op, as pending async packets from the
device should be cancelled on detach not on destroy.
Secondly having this as a bus op won't work with companion controllers, since
then there will be 1 bus driven by the ehci controller and thus 1 set of bus
ops, but the device being detached may be downstream of a handed over port.
Making the detach of a downstream device a port op allows the ehci controller
to forward this to the companion controller port for handed over ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This makes them consistent with the attach and detach ops, and in general
it makes sense to make portops take a port as argument. This also makes
adding support for a companion controller easier / cleaner.
[ kraxel: fix usb-musb.c build ]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cleanup / preparation patch for companion controller support. Note that
as a "side-effect" this patch also fixes the milkymist-softusb controller
not having a port_location set for its ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
expire_time must be initialited when the guest activates the
usb scheduler, not at device creation time.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds USBBusOps struct with (for now) only a single callback
which is called when a device is about to be destroyed. The USB Host
adapters are implementing this callback and use it to cancel any async
requests which might be in flight before the device actually goes away.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a usb_handle_packet function, put it into use everywhere.
Right now it just calls dev->info->handle_packet(), that will
change in future patches though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
UHCI host controller status register indicates error and
an interrupt is triggered on BABBLE and STALL errors.
Signed-off-by: Jan Vesely <jano.vesely@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a path string to USBPort. Add usb_port_location() function to set
the physical location of the usb port. Update all drivers implementing
usb ports to call it. Update the monitor commands to print it. Wind it
up in qdev.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add separate detach callback to USBPortOps, split
uhci/ohci/musb/usbhub attach functions into two.
Move common code to the usb_attach() function, only
the hardware-specific bits remain in the attach/detach
callbacks.
Keep track of the port it is attached to for each usb device.
[ v3: fix tyops in usb-musb.c ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Ports on root hub will have NULL here. This is needed to reconstruct
path from device to its root hub to build device path.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The commit 8e65b7c049 introduced
expire_time of UHCIState. But expire_time is not in vmstate, the
second uhci_frame_timer will not be fired immediately after loadvm.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
I have streaming audio devices working within qemu-kvm. This is a port
of the changes to qemu.
Streaming audio generates a series of isochronous requests that are
repetitive and time sensitive. The URBs need to be submitted in
consecutive USB frames and responses need to be handled in a timely manner.
Summary of the changes for isochronous requests:
1. The initial 'valid' value is increased to 32. It needs to be higher
than its current value of 10 since the host adds a 10 frame delay to the
scheduling of the first request; if valid is set to 10 the first
isochronous request times out and qemu cancels it. 32 was chosen as a
nice round number, and it is used in the path where a TD-async pairing
already exists.
2. The token field in the TD is *not* unique for isochronous requests,
so it is not a good choice for finding a matching async request. The
buffer (where to write the guest data) is unique, so use that value instead.
3. TD's for isochronous request need to be completed in the async
completion handler so that data is pushed to the guest as soon as it is
available. The uhci code currently attempts to process complete
isochronous TDs the next time the UHCI frame with the request is
processed. The results in lost data since the async requests will have
long since timed out based on the valid parameter. Increasing the valid
value is not acceptable as it introduces a 1+ second delay in the data
getting pushed to the guest.
4. The frame timer needs to be run on 1 msec intervals. Currently, the
expire time for the processing the next frame is computed after the
processing of each frame. This regularly causes the scheduling of frames
to shift in time. When this happens the periodic scheduling of the
requests is broken and the subsequent request is seen as a new request
by the host resulting in a 10 msec delay (first isochronous request is
scheduled for 10 frames from when the URB is submitted).
[ For what's worth a small change is needed to the guest driver to have
more outstanding URBs (at least 4 URBs with 5 packets per URB).]
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
Device names with whitespace require quoting in the shell and in the
monitor. Some of the offenders are also overly long. Some have a
more convenient alias, some don't.
The place for verbose device names is DeviceInfo member desc. The
name should be short & sweet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci.h declares some functions which aren't
defined in pci.h. Clean up moving things
to appropriate headers, and update all users.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch is preliminary for 64 bit BAR support.
Introduce dedicated type, pcibus_t, to represent pci bus address/size
instead of uint32_t.
Later this type will be changed to uint64_t.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make constants for pci base address match pci_regs.h by
renaming PCI_ADDRESS_SPACE_xxx to PCI_BASE_ADDRESS_SPACE_xxx.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
There is absolutely no need to call reset functions when initializing
devices. Since we are already registering them, calling qemu_system_reset()
should suffice. Actually, it is what happens when we reboot the machine,
and using the same process instead of a special case semantics will even
allow us to find bugs easier.
Furthermore, the fact that we initialize things like the cpu quite early,
leads to the need to introduce synchronization stuff like qemu_system_cond.
This patch removes it entirely. All we need to do is call qemu_system_reset()
only when we're already sure the system is up and running
I tested it with qemu (with and without io-thread) and qemu-kvm, and it
seems to be doing okay - although qemu-kvm uses a slightly different patch.
[ v2: user mode still needs cpu_reset, so put it in ifdef. ]
[ v3: leave qemu_system_cond for now. ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move usb code from vl.c to usb-bus.c and make it use the new data
structures added by qdev conversion. qemu usb core should be able
to handle multiple USB busses just fine now (untested though).
Kill some usb_*_init() legacy functions, use usb_create_simple()
instead.
Kill some FIXMEs added by the first qdev/usb patch.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* Add USBBus.
* Add USBDeviceInfo, move device callbacks here.
* Add usb-qdev helper functions.
* Switch drivers to qdev.
TODO:
* make the rest of qemu aware of usb busses and kill the FIXMEs
added by this patch.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I used the following command to enable debugging:
perl -p -i -e 's/^\/\/#define DEBUG/#define DEBUG/g' * */* */*/*
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The device is not reset on system reset currently.
Without this patch RHEL4.8 hangs after reboot if -usbdevice table
is in use.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This function is used to manage a PCI BAR, so make the more generic
pci_register_io_region() available to other uses.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
