Improve our braindead copy-on-read implementation. Pre-patch,
we have multiple issues:
- we create a bounce buffer and perform a write for the entire
request, even if the active image already has 99% of the
clusters occupied, and really only needs to copy-on-read the
remaining 1% of the clusters
- our bounce buffer was as large as the read request, and can
needlessly exhaust our memory by using double the memory of
the request size (the original request plus our bounce buffer),
rather than a capped maximum overhead beyond the original
- if a driver has a max_transfer limit, we are bypassing the
normal code in bdrv_aligned_preadv() that fragments to that
limit, and instead attempt to read the entire buffer from the
driver in one go, which some drivers may assert on
- a client can request a large request of nearly 2G such that
rounding the request out to cluster boundaries results in a
byte count larger than 2G. While this cannot exceed 32 bits,
it DOES have some follow-on problems:
-- the call to bdrv_driver_pread() can assert for exceeding
BDRV_REQUEST_MAX_BYTES, if the driver is old and lacks
.bdrv_co_preadv
-- if the buffer is all zeroes, the subsequent call to
bdrv_co_do_pwrite_zeroes is a no-op due to a negative size,
which means we did not actually copy on read
Fix all of these issues by breaking up the action into a loop,
where each iteration is capped to sane limits. Also, querying
the allocation status allows us to optimize: when data is
already present in the active layer, we don't need to bounce.
Note that the code has a telling comment that copy-on-read
should probably be a filter driver rather than a bolt-on hack
in io.c; but that remains a task for another day.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make it possible to inject errors on writes performed during a
read operation due to copy-on-read semantics.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Executing qemu with a terminal as stdin will temporarily alter stty
settings on that terminal (for example, disabling echo), because of
how we run both the monitor and any multiplexing with guest input.
Normally, qemu restores the original settings on exit; but if an
iotest triggers qemu to abort in the middle, we can be left with
the altered terminal setup. This can make life very annoying when
debugging an iotest failure (not everyone remembers the trick of
blind-typing 'stty sane' without echo, and some people prefer
terminal settings that are slightly different than the defaults
picked by 'stty sane').
It is possible to avoid qemu corrupting the terminal by not passing
a terminal to qemu's stdin in the first place (as in, use
'./check ... </dev/null'), but that's extra typing to have to
remember. But running 'exec </dev/null' in the harness seems like
it might be too heavy of a hammer. So I instead went the the
solution of saving and restoring the stty settings, only when the
harness detects that it is run interactively.
I tested this patch by forcing an allocation failure (I can't
guarantee that this particular limit will work on all setups, but
it shows the idea):
$ (ulimit -S -v 500000; ./check -qcow2 1)
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle a 0-length block status request up front, with a uniform
return value claiming the area is not allocated.
Most callers don't pass a length of 0 to bdrv_get_block_status()
and friends; but it definitely happens with a 0-length read when
copy-on-read is enabled. While we could audit all callers to
ensure that they never make a 0-length request, and then assert
that fact, it was just as easy to fix things to always report
success (as long as the callers are careful to not go into an
infinite loop). However, we had inconsistent behavior on whether
the status is reported as allocated or defers to the backing
layer, depending on what callbacks the driver implements, and
possibly wasting quite a few CPU cycles to get to that answer.
Consistently reporting unallocated up front doesn't really hurt
anything, and makes it easier both for callers (0-length requests
now have well-defined behavior) and for drivers (drivers don't
have to deal with 0-length requests).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make it easier to enable copy-on-read during iotests, by
exposing a new bool option to main and open.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We don't need to make any assumptions about the graph layout above the
top node of the commit operation any more. Remove the use of
bdrv_find_overlay() and related variables from the commit job code.
bdrv_drop_intermediate() doesn't use the 'active' parameter any more, so
we can just drop it.
The overlay node was previously added to the block job to get a
BLK_PERM_GRAPH_MOD. We really need to respect those permissions in
bdrv_drop_intermediate() now, but as long as we haven't figured out yet
how BLK_PERM_GRAPH_MOD is actually supposed to work, just leave a TODO
comment there.
With this change, it is now possible to perform another block job on an
overlay node without conflicts. qemu-iotests 030 is changed accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
QMP responses to certain commands can become quite long, which doesn't
only make reading them hard, but also means that the maximum line length
in patch emails can be exceeded. Allow tests to switch to QMP pretty
printing, which results in more, but shorter lines.
We also need to make sure to keep indentation in the response for this
to work as expected.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This changes the commit block job to support operation in a graph where
there is more than a single active layer that references the top node.
This involves inserting the commit filter node not only on the path
between the given active node and the top node, but between the top node
and all of its parents.
On completion, bdrv_drop_intermediate() must consider all parents for
updating the backing file link. These parents may be backing files
themselves and as such read-only; reopen them temporarily if necessary.
Previously this was achieved by the bdrv_reopen() calls in the commit
block job that made overlay_bs read-write for the whole duration of the
block job, even though write access is only needed on completion.
Now that we consider all parents, overlay_bs is meaningless. It is left
in place in this commit, but we'll remove it soon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no good reason for bdrv_drop_intermediate() to know the active
layer above the subchain it is operating on - even more so, because
the assumption that there is a single active layer above it is not
generally true.
In order to prepare removal of the active parameter, use a BdrvChildRole
callback to update the backing file string in the overlay image instead
of directly calling bdrv_change_backing_file().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
"check" is full of qemu-iotests--specific details. Separating it
from "common" does not make much sense anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The variable is almost unused, and one of the two uses is actually
uninitialized.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The variable is used in "common" but defined only after the file
is sourced.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Split "check" parts from tests part.
For the directory setup, the actual computation of directories goes
in "check", while the sanity checks go in the tests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It only provides functions used by the test programs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These are never used by "check", with one exception that does not need
$QEMU_OPTIONS. Keep them in common.rc, which will be soon included only
by the tests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of ./check failing when a binary is missing, we try each test
case now and each one fails with tons of test case diffs. Also, all the
variables were initialized by "check" prior to "common" being sourced,
and then (uselessly) checked for emptiness again in "check".
Centralize the search for programs in "common" (which will soon be
one with "check"), including the "realpath" invocation which can be done
just once in "check" rather than in the tests.
For qnio_server, move the detection to "common", simplifying
set_prog_path to stop handling the unused second argument, and
embedding the "realpath" pass.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some functions in common.rc are never used by the tests. Move
them out of that file and into common, which is already included
only by "check".
Code that actually *is* common to "check" and tests can be placed in
common.config.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This includes shell function, shell variables and command line options
(randomize.awk does not exist).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The condition of the for-loop makes sure that b is always smaller
than s->blocks, so the "if (b >= s->blocks)" statement is completely
superfluous here.
Buglink: https://bugs.launchpad.net/qemu/+bug/1715007
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all callers are using byte-based interfaces, there's no
reason for our internal hbitmap to remain with sector-based
granularity. It also simplifies our internal scaling, since we
already know that hbitmap widens requests out to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Both callers already had bytes available, but were scaling to
sectors. Move the scaling to internal code. In the case of
bdrv_aligned_pwritev(), we are now passing the exact offset
rather than a rounded sector-aligned value, but that's okay
as long as dirty bitmap widens start/bytes to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
iotests 165 was rather weak - on a default 64k-cluster image, where
bitmap granularity also defaults to 64k bytes, a single cluster of
the bitmap table thus covers (64*1024*8) bits which each cover 64k
bytes, or 32G of image space. But the test only uses a 1G image,
so it cannot trigger any more than one loop of the code in
store_bitmap_data(); and it was writing to the first cluster. In
order to test that we are properly aligning which portions of the
bitmap are being written to the file, we really want to test a case
where the first dirty bit returned by bdrv_dirty_iter_next() is not
aligned to the start of a cluster, which we can do by modifying the
test to write data that doesn't happen to fall in the first cluster
of the image.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is new code, but it is easier to read if it makes passes over
the image using bytes rather than sectors (and will get easier in
the future when bdrv_get_block_status is converted to byte-based).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some of the callers were already scaling bytes to sectors; others
can be easily converted to pass byte offsets, all in our shift
towards a consistent byte interface everywhere. Making the change
will also make it easier to write the hold-out callers to use byte
rather than sectors for their iterations; it also makes it easier
for a future dirty-bitmap patch to offload scaling over to the
internal hbitmap. Although all callers happen to pass
sector-aligned values, make the internal scaling robust to any
sub-sector requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Half the callers were already scaling bytes to sectors; the other
half can eventually be simplified to use byte iteration. Both
callers were already using the result as a bool, so make that
explicit. Making the change also makes it easier for a future
dirty-bitmap patch to offload scaling over to the internal hbitmap.
Remember, asking whether a byte is dirty is effectively asking
whether the entire granularity containing the byte is dirty, since
we only track dirtiness by granularity.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Thanks to recent cleanups, all callers were scaling a return value
of sectors into bytes; do the scaling internally instead.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Thanks to recent cleanups, most callers were scaling a return value
of sectors into bytes (the exception, in qcow2-bitmap, will be
converted to byte-based iteration later). Update the interface to
do the scaling internally instead.
In qcow2-bitmap, the code was specifically checking for an error
return of -1. To avoid a regression, we either have to make sure
we continue to return -1 (rather than a scaled -512) on error, or
we have to fix the caller to treat all negative values as error
rather than just one magic value. It's easy enough to make both
changes at the same time, even though either one in isolation
would work.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers to bdrv_dirty_iter_new() passed 0 for their initial
starting point, drop that parameter.
Most callers to bdrv_set_dirty_iter() were scaling a byte offset to
a sector number; the exception qcow2-bitmap will be converted later
to use byte rather than sector iteration. Move the scaling to occur
internally to dirty bitmap code instead, so that callers now pass
in bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the qcow2 bitmap
helper function sectors_covered_by_bitmap_cluster(), renaming it
to bytes_covered_by_bitmap_cluster() in the process.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Right now, the dirty-bitmap code exposes the fact that we use
a scale of sector granularity in the underlying hbitmap to anything
that wants to serialize a dirty bitmap. It's nicer to uniformly
expose bytes as our dirty-bitmap interface, matching the previous
change to bitmap size. The only caller to serialization is currently
qcow2-cluster.c, which becomes a bit more verbose because it is still
tracking sectors for other reasons, but a later patch will fix that
to more uniformly use byte offsets everywhere. Likewise, within
dirty-bitmap, we have to add more assertions that we are not
truncating incorrectly, which can go away once the internal hbitmap
is byte-based rather than sector-based.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are still using an internal hbitmap that tracks a size in sectors,
with the granularity scaled down accordingly, because it lets us
use a shortcut for our iterators which are currently sector-based.
But there's no reason we can't track the dirty bitmap size in bytes,
since it is (mostly) an internal-only variable (remember, the size
is how many bytes are covered by the bitmap, not how many bytes the
bitmap occupies). A later cleanup will convert dirty bitmap
internals to be entirely byte-based, eliminating the intermediate
sector rounding added here; and technically, since bdrv_getlength()
already rounds up to sectors, our use of DIV_ROUND_UP is more for
theoretical completeness than for any actual rounding.
Use is_power_of_2() while at it, instead of open-coding that.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We're already reporting bytes for bdrv_dirty_bitmap_granularity();
mixing bytes and sectors in our return values is a recipe for
confusion. A later cleanup will convert dirty bitmap internals
to be entirely byte-based, but in the meantime, we should report
the bitmap size in bytes.
The only external caller in qcow2-bitmap.c is temporarily more verbose
(because it is still using sector-based math), but will later be
switched to track progress by bytes instead of sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We've previously fixed several places where we failed to account
for possible errors from bdrv_nb_sectors(). Fix another one by
making bdrv_dirty_bitmap_truncate() take the new size from the
caller instead of querying itself; then adjust the sole caller
bdrv_truncate() to pass the size just determined by a successful
resize, or to reuse the size given to the original truncate
operation when refresh_total_sectors() was not able to confirm the
actual size (the two sizes can potentially differ according to
rounding constraints), thus avoiding sizing the bitmaps to -1.
This also fixes a bug where not all failure paths in
bdrv_truncate() would set errp.
Note that bdrv_truncate() is still a bit awkward. We may want
to revisit it later and clean up things to better guarantee that
a resize attempt either fails cleanly up front, or cannot fail
after guest-visible changes have been made (if temporary changes
are made, then they need to be cleanly rolled back). But that
is a task for another day; for now, the goal is the bare minimum
fix to ensure that just bdrv_dirty_bitmap_truncate() cannot fail.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We had several functions that no one is currently using, and which
use sector-based interfaces. I'm trying to convert towards byte-based
interfaces, so it's easier to just drop the unused functions:
bdrv_dirty_bitmap_get_meta
bdrv_dirty_bitmap_get_meta_locked
bdrv_dirty_bitmap_reset_meta
bdrv_dirty_bitmap_meta_granularity
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When subdividing a bitmap serialization, the code in hbitmap.c
enforces that start/count parameters are aligned (except that
count can end early at end-of-bitmap). We exposed this required
alignment through bdrv_dirty_bitmap_serialization_align(), but
forgot to actually check that we comply with it.
Fortunately, qcow2 is never dividing bitmap serialization smaller
than one cluster (which is a minimum of 512 bytes); so we are
always compliant with the serialization alignment (which insists
that we partition at least 64 bits per chunk) because we are doing
at least 4k bits per chunk.
Still, it's safer to add an assertion (for the unlikely case that
we'd ever support a cluster smaller than 512 bytes, or if the
hbitmap implementation changes what it considers to be aligned),
rather than leaving bdrv_dirty_bitmap_serialization_align()
without a caller.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only client of hbitmap_serialization_granularity() is dirty-bitmap's
bdrv_dirty_bitmap_serialization_align(). Keeping the two names consistent
is worthwhile, and the shorter name is more representative of what the
function returns (the required alignment to be used for start/count of
other serialization functions, where violating the alignment causes
assertion failures).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers of bdrv_img_create() pass in a size, or -1 to read the
size from the backing file. We then set that size as the QemuOpt
default, which means we will reuse that default rather than the
final parameter to qemu_opt_get_size() several lines later. But
it is rather confusing to read subsequent checks of 'size == -1'
when it looks (without seeing the full context) like size defaults
to 0; it also doesn't help that a size of 0 is valid (for some
formats).
Rework the logic to make things more legible.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
- support for IDA (indirect addressing in ccws) via ccw data stream
- support for extended TOD-Clock (z14 feature)
- various fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=0/U5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20171006' into staging
s390x changes:
- support for IDA (indirect addressing in ccws) via ccw data stream
- support for extended TOD-Clock (z14 feature)
- various fixes and improvements all over the place
# gpg: Signature made Fri 06 Oct 2017 10:52:22 BST
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20171006: (33 commits)
hw/s390x: Mark the "sclpquiesce" device with user_creatable = false
s390x/tcg: initialize machine check queue
s390x/sclp: mark sclp-cpu-hotplug as non-usercreatable
s390x/sclp: Mark the sclp device with user_creatable = false
s390/kvm: make TOD setting failures fatal for migration
s390/kvm: Support for get/set of extended TOD-Clock for guest
s390x/css: fix css migration compat handling
s390x: sort some devices into categories
s390x/tcg: make STFL store into the lowcore
s390x: introduce and use S390_MAX_CPUS
target/s390x: get rid of next_core_id
s390x/cpumodel: fix max STFL(E) bit number
s390x: raise CPU hotplug irq after really hotplugged
MAINTAINERS: use KVM s390x maintainers for kvm-stubs.c and kvm_s390x.h
s390x/3270: handle writes of arbitrary length
s390x/3270: IDA support for 3270 via CcwDataStream
Revert "s390x/ccw: create s390 phb conditionally"
s390x/tcg: make idte/ipte use the new _real mmu
s390x/tcg: make testblock use the new _real mmu
s390x/tcg: make stora(g) use the new _real mmu
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "sclpquiesce" device is just an internal device that should not be
created by the user directly. Though it currently does not seem to cause
any obvious trouble when the user instantiates an additional device, let's
better mark it with user_creatable = false to avoid unexpected behavior,
e.g. because the quiesce notifier gets registered multiple times.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1507193105-15627-1-git-send-email-thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Just as for external interrupts and I/O interrupts, we need to
initialize mchk_index during cpu reset.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
A TYPE_SCLP_CPU_HOTPLUG device for handling cpu hotplug events
is already created by the sclp event facility. Adding a second
TYPE_SCLP_CPU_HOTPLUG device via -device sclp-cpu-hotplug creates
an ambiguity in raise_irq_cpu_hotplug(), leading to a crash once
a cpu is hotplugged.
To fix this, disallow creating a sclp-cpu-hotplug device manually.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The "sclp" device is just an internal device that can not be instantiated
by the users. If they try to use it, they only get a simple error message:
$ qemu-system-s390x -nographic -device sclp
qemu-system-s390x: Option '-device s390-sclp-event-facility' cannot be
handled by this machine
Since sclp_init() tries to create a TYPE_SCLP_EVENT_FACILITY which is
a non-pluggable sysbus device, there is really no way that the "sclp"
device can be used by the user, so let's set the user_creatable = false
accordingly.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1507125199-22562-1-git-send-email-thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If we fail to set a proper TOD clock on the target system, this can
already result in some problematic cases. We print several warn messages
on source and target in that case.
If kvm fails to set a nonzero epoch index, then we must ultimately fail
the migration as this will result in a giant time leap backwards. This
patch lets the migration fail if we can not set the guest time on the
target.
On failure the guest will resume normally on the original host machine.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split failure change from epoch index change, minor fixups]
Message-Id: <20171004105751.24655-3-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Provides an interface for getting and setting the guest's extended
TOD-Clock via a single ioctl to kvm. If the ioctl fails because it
is not support by kvm, then we fall back to the old style of
retrieving the clock via two ioctls.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split failure change from epoch index change]
Message-Id: <20171004105751.24655-2-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
[some cosmetic fixes]
Commit e996583eb3 ("s390x/css: activate ChannelSubSys migration",
2017-07-11) was supposed to enable css migration for virtio-ccw
machines starting 2.10, but it ended up effectively enabling it
only for 2.10 as the registration of the appropriate VMStateDescription
happens in ccw_machine_2_10_instance_options which does not get
called for machines more recent than 2_10.
Let us move the corresponding chunk of code (which conditionally enables
the migration based on the value of the corresponding class property) to
ccw_init, which is called for each virtio-ccw machine instance.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20171004110109.16525-1-pasic@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
