Most of the calls to tcg_opt_gen_mov are preceeded by a test to check if
the source temp is a constant. Fold that into the tcg_opt_gen_mov
function.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433495958-9508-1-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Each call to tcg_opt_gen_mov is preceeded by a test to check if the
source and destination temps are copies. Fold that into the
tcg_opt_gen_mov function.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433447607-31184-4-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We can get the opcode using the TCGOp pointer. It needs to be
dereferenced, but it's anyway done a few lines below to write
the new value.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433447607-31184-3-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We can get the opcode using the TCGOp pointer. It needs to be
dereferenced, but it's anyway done a few lines below to write
the new value.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433447607-31184-2-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
When the same temp is used twice or more as an input argument to a TCG
instruction, the dead computation code doesn't recognize the second use
as a dead temp. This is because the temp is marked as live in the same
loop where dead inputs are checked.
The fix is to split the loop in two parts. This avoid emitting a move
and using a register for the movcond instruction when used as "move if
true" on x86-64. This might bring more improvements on RISC TCG targets
which don't have outputs aliased to inputs.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433447228-29425-3-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
For TCG ops with two outputs registers (add2, sub2, div2, div2u), when
the same input temp is used for the two inputs aliased to the two
outputs, and when these inputs are both dead, the register allocation
code wrongly assigned the same register to the same output.
This happens for example with sub2 t1, t2, t3, t3, t4, t5, when t3 is
not used anymore after the TCG op. In that case the same register is
used for t1, t2 and t3.
The fix is to look for already allocated aliased input when allocating
a dead aliased input and check that the register is not already
used.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1433447228-29425-2-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The addition of MO_AMASK means that places that used inverted masks
need to be changed to use positive masks, and places that failed to
mask the intended bits need updating.
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Tested-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This will be used to size the TLB when more than 8 MMU modes are
used by the target. Limitations come from the limited size of
the immediate fields (which sometimes, as in the case of Aarch64,
extend to instructions that shift the immediate).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1424436345-37924-2-git-send-email-pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
tcg-target.h does not use any QEMU-specific symbols, save for tci's usage
of CPUArchState. Pull that up to tcg/tcg.h.
This will make it possible to include tcg-target.h in cpu-defs.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
These modifiers control, on a per-memory-op basis, whether
unaligned memory accesses are allowed. The default setting
reflects the target's definition of ALIGNED_ONLY.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The extra information is not yet used but it is now available.
This requires minor changes through all of the tcg backends.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
At the tcg opcode level, not at the tcg-op.h generator level.
This requires minor changes through all of the tcg backends,
but none of the cpu translators.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
No code uses the cpu_pc_from_tb() function. Delete from tricore and
arm which each provide an unused implementation. Update the comment
in tcg.h to reflect that this is obsoleted by synchronize_from_tb.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 951c6300f7 out-of-lined the 32-bit-host versions of
tcg_gen_{ld,st}_i64, but in the process it inadvertently changed
an #ifdef HOST_WORDS_BIGENDIAN to #ifdef TCG_TARGET_WORDS_BIGENDIAN.
Since the latter doesn't get defined anywhere this meant we always
took the "LE host" codepath, and stored the two halves of the value
in the wrong order on BE hosts. This typically breaks any 64-bit
guest on a 32-bit BE host completely, and will have possibly more
subtle effects even for 32-bit guests.
Switch the ifdef back to HOST_WORDS_BIGENDIAN.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1428523029-13620-1-git-send-email-peter.maydell@linaro.org
As seen with ubuntu-5.10-live-powerpc.iso.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Pre-allocating 512 of them per TB is a waste.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This is less about improved type checking than enabling a
subsequent change to the representation of labels.
Acked-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This is improved type checking for the translators -- it's no longer
possible to accidentally swap arguments to the branch functions.
Note that the code generating backends still manipulate labels as int.
With notable exceptions, the scope of the change is just a few lines
for each target, so it's not worth building extra machinery to do this
change in per-target increments.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Anthony Green <green@moxielogic.com>
Cc: Jia Liu <proljc@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Pre-allocating 640 of them per TB is a waste.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We no longer need INDEX_op_end to terminate the list, nor do we
need 5 forms of nop, since we just remove the TCGOp instead.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rather reserving space in the op stream for optimization,
let the optimizer add ops as necessary.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
With the linked list scheme we need not leave nops in the stream
that we need to process later.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The previous setup required ops and args to be completely sequential,
and was error prone when it came to both iteration and optimization.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The method by which we count the number of ops emitted
is going to change. Abstract that away into some inlines.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Almost completely eliminates the ifdefs in this file, improving
confidence in the lesser used 32-bit builds.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Some of these functions are really quite large. We have a number of
things that ought to be circularly dependent, but we duplicated code
to break that chain for the inlines.
This saved 25% of the code size of one of the translators I examined.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Currently 'info jit' outputs half of the information to monitor and the
rest to qemu log. Dumping opcode counts to monitor as a part of 'info
jit' command doesn't sound useful. Add new monitor command 'info
opcount' that only dumps opcode counters.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Commit 9d8bf2d1 moved the softmmu slow path out of line and introduce a
regression at the same time by always calling tcg_out_tlb_load with
is_load=1. This makes impossible to run any significant code under
qemu-system-mips*.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of using structures, which imply some amount of overhead
on certain ABIs, use pointer types.
This actually reduces the size of the binaries vs a NON-debug
build on ppc64 and x86_64, due to a reduction in the number of
sign-extension insns.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The "old" qemu_ld opcode did not specify the size of the result,
and so we had to assume full register width. With the new opcodes,
we can narrow the result.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The pre-v9 ADDX/SUBX insns were renamed ADDC/SUBC for v9.
Standardizing on the v9 name makes things less confusing.
Signed-off-by: Richard Henderson <rth@twiddle.net>
On T4 and newer Sparc chips we have an add-with-carry insn
that takes its input from %xcc instead of %icc.
Signed-off-by: Richard Henderson <rth@twiddle.net>
fopen() may fail and it does not check its return vaule here,
it is better to dump op count to the normal log file.
Signed-off-by: Li Liu <john.liuli@huawei.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add back in the support for 64-bit PPC MacOSX hosts that was
broken in the recent merge of the 32-bit and 64-bit TCG backends.
Reported-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tested-by: Andreas Färber <andreas.faerber@web.de>
With rt != r0 on loads, we use rt for scratch. If we need an index
register different from base, we can't use rt, but r0 is usable.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1403843160-30332-1-git-send-email-rth@twiddle.net
Tested-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The tcg_out* and tcg_patch* functions are utility routines that may or
may not be used by a particular backend; mark them with the 'unused'
attribute to suppress spurious warnings if they aren't used.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This can significantly reduce code size for generation of (some)
64-bit constants. With the side effect that we know for a fact
that exit_tb can use the register to good effect.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
As a "utility", it only supported ppc, and in a way that other
tcg backends provided directly in tcg-target.h. Removing this
disparity is easier now that the two ppc backends are merged.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The other tcg backends that support 32- and 64-bit modes
use the 32-bit name for the port. Follow suit.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Good enough to run some instructions before things go awry.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Now passes tcg_add_target_add_op_defs assertions, but
not complete enough to function.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Just enough to compile, assuming you edit config-host.mak manually.
It will still abort at runtime, due to missing brcond2, setcond2, mulu2.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The new ELFv2 ABI, used by default on powerpc64le-linux hosts,
introduced some changes that are incompatible with code currently
generated by the ppc64 TGC target. In particular, we no longer
use function descriptors.
This patch adds support for the ELFv2 ABI in the ppc64 TGC
function call and function prologue sequences.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The correct test uses the _CALL_AIX macro, not a host-specific macro.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The calling convention reserves space for the 8 register parameters on
the stack, so using only 6*8=48 as the offset was wrong. We never saw
this bug because we don't have any helpers with more than 5 parameters.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
These values are private to tcg.c; we don't need to expose
this nonsense to the translators.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rather than using tcg_out32 and opcodes directly. This allows us
to remove LD_ADDR and CMP_L macros.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
In order to be able to use tcg_out_ld/st sensibly with scratch
registers, assert only when we'd incorrectly clobber a scratch.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Code movement only. This will allow us to make use of the
other tcg_out_* functions in tidying their implementations.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
With the "old" ldst ops we didn't know the real width of the
result of the load, but with the "new" ldst ops we do.
Signed-off-by: Richard Henderson <rth@twiddle.net>
* remotes/bonzini/softmmu-smap: (33 commits)
target-i386: cleanup x86_cpu_get_phys_page_debug
target-i386: fix protection bits in the TLB for SMEP
target-i386: support long addresses for 4MB pages (PSE-36)
target-i386: raise page fault for reserved bits in large pages
target-i386: unify reserved bits and NX bit check
target-i386: simplify pte/vaddr calculation
target-i386: raise page fault for reserved physical address bits
target-i386: test reserved PS bit on PML4Es
target-i386: set correct error code for reserved bit access
target-i386: introduce support for 1 GB pages
target-i386: introduce do_check_protect label
target-i386: tweak handling of PG_NX_MASK
target-i386: commonize checks for PAE and non-PAE
target-i386: commonize checks for 4MB and 4KB pages
target-i386: commonize checks for 2MB and 4KB pages
target-i386: fix coding standards in x86_cpu_handle_mmu_fault
target-i386: simplify SMAP handling in MMU_KSMAP_IDX
target-i386: fix kernel accesses with SMAP and CPL = 3
target-i386: move check_io helpers to seg_helper.c
target-i386: rename KSMAP to KNOSMAP
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unify pieces of cpu-all.h, exec-all.h, softmmu_exec.h and tcg/tcg.h
into a single new header file with all helpers.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We expose a generic helper "tcg_gen_extr_i64_tl" for 64bit targets, but the
same function for 32bit targets is a misnomer and refers to an invalid function
name.
Fix up the definition to point to the correct internal helper names instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Since all backends have been converted, remove the compatibility code.
Acked-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The first non-register argument isn't placed at offset 0.
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
For a 64-bit host, the high bits of a register after a 32-bit operation
are undefined. Adjust the temps mask for all 32-bit ops to reflect that.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Adjust the FDE to point to the code_buffer after we've copied it
to the image, rather than requiring that the backend set it prior.
This allows the backend to use read-only storage for its data.
Signed-off-by: Richard Henderson <rth@twiddle.net>
This will let us find all the info from the hash table.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rather than special casing them, use the standard mechanisms
for tcg helper generation.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rather than include helper.h with N values of GEN_HELPER, include a
secondary file that sets up the macros to include helper.h. This
minimizes the files that must be rebuilt when changing the macros
for file N.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
If either the high or low pair can be resolved, we can
simplify to either a constant or to a 32-bit comparison.
Signed-off-by: Richard Henderson <rth@twiddle.net>
* remotes/rth/tcg-mips: (24 commits)
tcg-mips: Enable direct chaining of TBs
tcg-mips: Simplify movcond
tcg-mips: Simplify brcond2
tcg-mips: Improve setcond eq/ne vs zeros
tcg-mips: Simplify setcond2
tcg-mips: Simplify brcond
tcg-mips: Simplify setcond
tcg-mips: Commonize opcode implementations
tcg-mips: Improve add2/sub2
tcg-mips: Hoist args loads
tcg-mips: Fix subtract immediate range
tcg-mips: Name the opcode enumeration
tcg-mips: Use EXT for AND on mips32r2
tcg-mips: Use T9 for TCG_TMP1
tcg-mips: Introduce TCG_TMP0, TCG_TMP1
tcg-mips: Rearrange register allocation
tcg-mips: Convert to new_ldst
tcg-mips: Convert to new qemu_l/st helpers
tcg-mips: Move softmmu slow path out of line
tcg-mips: Split large ldst offsets
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the code_gen_buffer is constrained to not cross 256mb
regions, we are assured that we can use J to reach another TB.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use the same table to fold comparisons as with setcond.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Emitting a single branch instead of (up to) 3, using setcond2
to generate the composite compare.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The original code results in one too many insns per zero
present in the input. And since comparing 64-bit numbers
vs zero is common...
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Using tcg_unsigned_cond and tcg_high_cond.
Also, move the function up in the file for future cleanups.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use the same table to fold comparisons as with setcond.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use a table to fold comparisons to less-than.
Also, move the function up in the file for futher simplifications.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Most opcodes fall in to one of a couple of patterns.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Since we must use ADDUI, we would generate incorrect code for -32768.
Leaving off subtract of +32768 makes things easier for a follow-on patch.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
At the same time, tidy deposit by introducing tcg_out_opc_bf.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
T0 is an argument register for the n32 and n64 abis. T9 is the call
address register for the abis, and is more directly under the control
of the backend.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use these instead of hard-coding the registers to use for temporaries.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use FP (also known as S8) as a normal call-saved register.
Include T0 in the allocation order and call-clobbered list
even though it's currently used as a TCG temporary.
Put the argument registers at the end of the allocation order.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
In addition, fill delay slots calling the helpers and tail
call to the store helpers.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
At the same time, tidy up the call helpers, avoiding a memory reference.
Split out several subroutines. Use TCGMemOp constants. Make endianness
selectable at runtime.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
For userland builds calls will normally be in range,
and for the exit_tb opcode the branch to the epilogue.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Broken since dddbb2e1e3.
Do all the rest of the things that tcg_out_op did before
and after the big switch statement.
Signed-off-by: Richard Henderson <rth@twiddle.net>
There are a variety of common cases for which we can use carry tricks to
avoid a conditional branch. On very new hardware, use LOAD ON CONDITION
instead of a conditional branch.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Elides two insns from the sequence. The resulting tlb compare
sequence is satisfyingly minimal:
risbg %r2,%r8,51,186,56
risbg %r3,%r8,61,178,0
cg %r3,904(%r10,%r2)
lg %r2,920(%r10,%r2)
jlh tlb_miss
Signed-off-by: Richard Henderson <rth@twiddle.net>
Commit af3cbfbe80 hoisted some "common"
loads of the temporary type, forgetting that the types could differ
during truncating moves. This affects the correctness of the memory
offset on big-endian hosts.
Tested-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The INDEX_op_call case has just been obsoleted; the mov and movi
cases have not been reachable for years. Attempt to document this
both in each tcg_out_op switch, and via TCG_OPF_NOT_PRESENT.
Because of the TCG_OPF_NOT_PRESENT change, this must be done for
all targets in a single commit.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The move opcodes are special in that their constraints must cover
all available registers. So instead of checking the constraints,
just use the available registers.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Avoid allocating a tcg temporary to hold the constant address,
and instead place it directly into the op_call arguments.
At the same time, convert to the newly introduced tcg_out_call
backend function, rather than invoking tcg_out_op for the call.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Now that all backends do define TCG_TARGET_INSN_UNIT_SIZE,
remove the fallback definition.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Using a 16-byte aligned structure achieves best results, both for code
cleanliness and compiled code size. However, this means that we can't
use the trick of encoding the slot number into the low 2 bits.
Thankfully, we only ever use slot2, so make that explicit in the names
of the relocation functions, and drop the code for other slots.
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Acked-by: Claudio Fontana <claudio.fontana@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
To be defined by the tcg backend based on the elemental unit of the ISA.
During the transition, allow TCG_TARGET_INSN_UNIT_SIZE to be undefined,
which allows us to default tcg_insn_unit to the current uint8_t.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
To avoid C undefined behaviour when patching generated code,
provide wrappers tcg_patch8/16/32/64 which use the usual memcpy
trick, and use them in the i386 backend.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Avoid stores to unaligned addresses in TCG code generation, by using the
usual memcpy() approach. (Using bswap.h would drag a lot of QEMU baggage
into TCG, so it's simpler just to do direct memcpy() here.)
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use TCGReg everywhere appropriate. Use int32_t for all arguments
that may be registers or immediate constants. Merge tcg_out_addi
into its only caller.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use sextract instead of raw bit shifting for the tests. Introduce
a new check_fit_ptr macro to make it clear we're looking at pointers.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Using the 32-bit SMUL is a tad more efficient than
resorting to extending and using the 64-bit MULX.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Quite a lot of effort was spent composing and decomposing 64-bit
quantities in registers, when we should just create them and leave
them as one 64-bit register.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Replace with SPARC64 define. Soon even sparcv8plus will use
64-bit register as far as TCG is concerned.
Signed-off-by: Richard Henderson <rth@twiddle.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTVthUAAoJEK0ScMxN0Ceb5OUH/0Ri4engOQim3mV1jAOr2Vca
3zg+Hl8b+UioXD0se24Iipr6s+02G1DApbbLPX7DZAnoh9jEBvDtHOdde3pNbMkQ
jcTpShTyT7OKSsklRN19ckvk0ffBch5W3Ekkw6/Hg6ys2HIvirRpEL6R58oJNlP6
xcCkQZISZVkakbv5xft8YQo1v8wnU5q2l85OaC1aaDB6g+Y6ZgoA1qkWjqlHkmQk
1asflfbC0r5ke+yx7vz6310f5xBDLSVv17dqsDUr70o1m/6bem6wQXMczwmYUfk5
99OCPiqdiCZLJyVFvIvfwSakL9Bq/nvnmywXTkrB7rovk5VZz3gc4sJkuUkL+KM=
=URV1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/tcg-next-20140422' into staging
Pull tcg 2014-04-22
# gpg: Signature made Tue 22 Apr 2014 22:00:04 BST using RSA key ID 4DD0279B
# gpg: Can't check signature: public key not found
* remotes/rth/tags/tcg-next-20140422:
tcg: Use HOST_WORDS_BIGENDIAN
tcg: Fix fallback from muls2_i64 to mulu2_i64
tcg: Use tcg_gen_mulu2_i32 in tcg_gen_muls2_i32
tcg: Relax requirement for mulu2_i32 on 32-bit hosts
tcg-s390: Remove W constraint
tcg-sparc: Use the type parameter to tcg_target_const_match
tcg-ppc64: Use the type parameter to tcg_target_const_match
tcg-aarch64: Remove w constraint
tcg: Add TCGType parameter to tcg_target_const_match
tcg: Fix out of range shift in deposit optimizations
tci: Mask shift counts to avoid undefined behavior
tcg: Mask shift quantities while folding
tcg: Use "unspecified behavior" for shifts
tcg: Fix warning (1 bit signed bitfield entry) and replace int by bool
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Brown Bag sez, don't put the fallback code into the wrong function.
Also, check for muluh_i64 and use tcg_gen_mulu2_i64 instead of raw ops.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Instead require either mulu2_i32 or muluh_i32. The code in tcg-op.h
already supports looking for both. Previous incomplete conversion?
Signed-off-by: Richard Henderson <rth@twiddle.net>
Most 64-bit targets need to be able to ignore the high bits
of a TCG_TYPE_I32 value.
Suggested-by: Stuart Brady <sdb@zubnet.me.uk>
Signed-off-by: Richard Henderson <rth@twiddle.net>
By inspection, for a deposit(x, y, 0, 64), we'd have a shift of (1<<64)
and everything else falls apart. But we can reuse the existing deposit
logic to get this right.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The TCG result would be undefined, but we can at least produce one
plausible result and avoid triggering the wrath of analysis tools.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Change the definition such that shifts are not allowed to crash
for any input.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Static code analyzers complain about signed bitfields with only a single
bit. is_ld is used as a boolean value, so make it bool.
ppc64 already used bool for the 2nd argument is_ld of the local function
add_qemu_ldst_label. Modify all other TCG targets to do follow this
example.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Still inline, but updated to the new routines. Always use the LE
helpers, reusing the bswap between the fast and slot paths.
Signed-off-by: Richard Henderson <rth@twiddle.net>
This sequencing requires 5 stop bits instead of 6, and has room left
over to pre-load the tlb addend, and bswap data prior to being stored.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The assembler seems to prefer them, perhaps we should too.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Replace aarch64_ldst_op_data with AArch64LdstType, as it wasn't encoded
for the proper shift for the field and was confusing.
Merge aarch64_ldst_op_data, AArch64LdstType, and a few stray opcode bits
into a single I3312_* argument, eliminating some magic numbers from the
helper functions.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Cleaning up the implementation of REV and REV16 at the same time.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Making the bswap conditional on the memop instead of a compile-time test.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
In some cases, a direct branch will be in range.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Some guest env are small enough to reach the tlb with only a 12-bit addition.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Combines 4 other inline functions and tidies the prologue.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
It's obviously call-clobbered, but is otherwise unused.
Repurpose it as the TCG temporary.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
A compare and branch against zero happens at the start of
every single TB.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rearrange code to put the compare and branch in the same place.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The subset of logical immediates that we support is quite quick to test,
and such constants are quite common to want to load.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
When profitable, initialize the register with MOVN instead of MOVZ,
before setting the remaining lanes with MOVK.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rather than raw constants that could mean anything.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The arm ldrd/strd insns must cause alignment traps, whereas
at least for armv7 ldr/str must handle unaligned operations.
While this is hardly the only problem facing user-only emu,
this solves one problem for i386 on armv7 emulation.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
All of the helpers with the explicit big/little endian option
require the return address as a parameter. Acquire this via
a trampoline.
Move the load of areg0 into the trampoline.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Pass address registers explicitly, rather than as indicies of args[].
It's two argument registers either way. Use more TCGReg as appropriate.
Signed-off-by: Richard Henderson <rth@twiddle.net>
We were computing the full address into %o0 and then not using it.
Adjust some of the computation to rely less on having to pull immediate
values into registers.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Cleaning up the implementation of tcg_out_movi at the same time.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Clean up multiply at the same time.
For remainder, generic code will produce mul+sub,
whereas we can implement with msub.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Also tidy the implementation of ubfm, sbfm, extr in order to share code.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Handle a simplified set of logical immediates for the moment.
The way gcc and binutils do it, with 52k worth of tables, and
a binary search depth of log2(5334) = 13, seems slow for the
most common cases.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Avoid the magic numbers in the current implementation.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
This merges the implementation of tcg_out_addi and tcg_out_subi.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Converting the add/sub (3.5.2) and logical shifted (3.5.10) instruction
groups to the new scheme.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Commit 023261ef85 failed to remove a
nop that's no longer required.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
At first glance the code appears to be using 1's compliment encoding,
a-la AArch32. Except that the constant is "off", creating a complicated
split field 2's compliment encoding.
Much clearer to just use a normal mask and shift.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
It was unused. Let's not overcomplicate things before we need them.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This reduces the code size of the function significantly.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We assert that the values for _I32 and _I64 are 0 and 1 respectively.
This will make a couple of functions declared by tcg.c cleaner.
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Removed from other targets in 56bbc2f967.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Win32 doesn't have a cpuid.h, and MacOSX may have one but without
the __cpuid() function we use, which means that commit 9d2eec20
broke the build for those platforms. Fix this by tightening up
our configure cpuid.h check to test that the functions we need
are present, and adding some missing #ifdef guards in
tcg/i386/tcg-target.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
These three-operand shift instructions do not require the shift count
to be placed into ECX. This reduces the number of mov insns required,
with the mere addition of a new register constraint.
Don't attempt to get rid of the matching constraint, as that's impossible
to manipulate with just a new constraint. In addition, constant shifts
still need the matching constraint.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Note that the optimizer cannot simplify ANDC X,Y,C to AND X,Y,~C
so we must handle constants in the implementation of andc.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
